Blade Lift
Show/hide table
 | |
| Illustration 1 | g03597836 |
Show/hide table
| Specification for 261-8536 Blade Lift Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 288-0735 Bolt | Torque to 50 ± 10 N·m (36.87800 ± 7.37560 lb ft). |
| 2 | As required, use the thrust washers to obtain minimum gap between lift arm and frame center shift plates. Note: First shim shall be placed in rear of the joint. For any additional shims being used, split between the front and rear as best as possible. |
||
| 2 | 8D-4336 Thrust Washer | Thickness of one thrust washer is 1.90 ± 0.18 mm (0.075 ± 0.007 inch). |
|
| 4 | As required, use the shims to obtain maximum end play of 0.25 mm (0.010 inch). So yoke assembly (3) will rotate without binding. |
||
| 8 | 7D-8879 Shim | Thickness of one shim is 0.13 mm (0.005 inch). |
|
| 6 | 7D-8881 Shim | Thickness of one shim is 0.25 mm (0.010 inch). |
|
| 2 | 7D-8882 Shim | Thickness of one shim is 0.51 mm (0.020 inch). |
|
| 5 | 1 | 8X-5107 Pin | Diameter is 60.26 ± 0.03 mm (2.372 ± 0.001 inch). |
Show/hide table
 | |
| Illustration 2 | g03597856 |
View of area C | |
Show/hide table
| Item | Qty | Part | Specification Description |
| - | Do not use impact type driver to assemble bearings. | ||
| 6 | 1 | 7D-8889 Bearing | Diameter is 76.352 ± 0.050 mm (3.0060 ± 0.0020 inch). |
| 7 | 1 | 8D-8168 Bearing | Diameter is 63.65 ± 0.05 mm (2.506 ± 0.002 inch). |
Caterpillar Information System:
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Left Drag Conveyor and Right Auger Conveyor) - Install
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Assemble
2005/02/07 A Correction to A New Engine Coolant Heater Is Available {1383}
793D Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve - Install
793D Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve - Remove
793D Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Install
793D Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Remove
PM-201 Cold Planer Belt - Inspect/Adjust/Replace
2005/06/13 The Load Control Valve (Drift Reduction Valve) for the Boom Is Improved {5067, 5117, 5147, 5811}
PM-201 Cold Planer Belt Tensioner (Rotor Drive) Pulley - Lubricate
R2900G Load Haul Dump Braking System Solenoid Valve (Parking Brake) - Test
R2900G Load Haul Dump Lubricant Viscosities
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Fuel Tank - Remove
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 2119 - FMI 03
14L Motor Grader Machine Systems Circle
120M, 12M, 140M and 160M Motor Graders Machine Systems Front Axle
120M, 12M, 140M and 160M Motor Graders Machine Systems Step Group
120M, 12M, 140M and 160M Motor Graders Machine Systems Governor (Air Compressor) - Test and Adjust
PM-201 Cold Planer Circuit Breakers - Reset
2005/02/07 The Sleeve Bearings That Are Used In Some Idler Gears, Cluster Gears, Cage Assemblies, And Adapter Assemblies Are Now Available For Parts Service {1206, 7551}
2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
C11 and C15 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
793D Off-Highway Truck/Tractor Electronic Control Module (Road Analysis Control) - Remove and Install
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Remove