Fuel Tank - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 4     |
开始:
- 连接转向机架锁。 请参阅拆解和组装, "转向机架锁 - 分离和连接"。
- 拆卸前车桥防护罩。 请参阅拆解和组装, "车桥防护罩(前)- 拆卸和安装"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将燃油箱中的油排入适当的容器中,以便保存或处理。 燃油箱的容量为 724 L (191 US gal)。
- 拆下中间盖 (1) 。
Show/hide table
图 1 | g01141031 |
- 拆下左侧盖 (2) 。 对右侧盖重复此过程。
- 拆下盖 (3) 。
Show/hide table
图 2 | g01141033 |
- 拆下卡箍 (4) 。
Show/hide table
图 3 | g01141051 |
- 将螺栓 (6) 从盖组件 (5) 上拆下。
Show/hide table
图 4 | g01141052 |
- 将工具 (A) 和适当的起吊设备连接到盖组件 (5) 上。 拆下盖 (5) 。 盖 (5) 的重量约为 70 kg (155 lb)。
Show/hide table
图 5 | g01141053 |
- 连接软管组件 (7) 和 (8) 。
Show/hide table
图 6 | g01141054 |
- 断开软管组件 (9) 和 (10) 。
Show/hide table
图 7 | g01141055 |
- 断开线束组件 (11) 。
- 将工具 (A) 和适当的起吊设备安装到安装板 (12) 上。 拆下螺栓 (13) 。 拆下安装板 (12) 。 安装板 (12) 的重量约为 127 kg (280 lb)。
Show/hide table
图 8 | g01141056 |
- 拆卸螺栓 (14) 和 (15) 。
Show/hide table
图 9 | g01141057 |
- 断开线束组件 (16) 。
- 拆下螺栓 (18) 。 由两人拆下中央防护罩 (17) 。 中央防护罩 (17) 的重量约为 19 kg (42 lb)。
Show/hide table
图 10 | g01141061 |
- 拆下螺栓 (19) 。 由两人拆下左防护罩组件 (20) 。 左防护罩组件 (20) 的重量约为 41 kg (90 lb)。 对右防护罩组件重复此过程。
Show/hide table
图 11 | g01141063 |
- 将螺栓 (22) 从燃油箱 (21) 上拆下。 对另一侧重复此操作。
Show/hide table
图 12 | g01141065 |
前侧左视图 |
- 将阀 (23) 转到闭合位置。
Show/hide table
图 13 | g01141066 |
- 拆下螺栓 (25) 和夹子。 断开软管组件 (24) 。
- 拆下螺栓 (26) 。 对另一侧重复此操作。
Show/hide table
图 14 | g01141069 |
- 将工具 (A) 和适当的起吊设备安装到燃油箱 (21) 的顶部。 拆下燃油箱 (21) 。 燃油箱 (21) 的重量约为 387 kg (855 lb)。
Show/hide table
图 15 | g01141072 |
Caterpillar Information System:
120M, 12M, 140M and 160M Motor Graders Machine Systems Blade Lift
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Left Drag Conveyor and Right Auger Conveyor) - Install
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Assemble
2005/02/07 A Correction to A New Engine Coolant Heater Is Available {1383}
793D Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve - Install
793D Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve - Remove
793D Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Install
793D Off-Highway Truck Power Train Oil Filter and Base (Transmission Charging) - Remove
PM-201 Cold Planer Belt - Inspect/Adjust/Replace
2005/06/13 The Load Control Valve (Drift Reduction Valve) for the Boom Is Improved {5067, 5117, 5147, 5811}
PM-201 Cold Planer Belt Tensioner (Rotor Drive) Pulley - Lubricate
R2900G Load Haul Dump Braking System Solenoid Valve (Parking Brake) - Test
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 2119 - FMI 03
14L Motor Grader Machine Systems Circle
120M, 12M, 140M and 160M Motor Graders Machine Systems Front Axle
120M, 12M, 140M and 160M Motor Graders Machine Systems Step Group
120M, 12M, 140M and 160M Motor Graders Machine Systems Governor (Air Compressor) - Test and Adjust
PM-201 Cold Planer Circuit Breakers - Reset
2005/02/07 The Sleeve Bearings That Are Used In Some Idler Gears, Cluster Gears, Cage Assemblies, And Adapter Assemblies Are Now Available For Parts Service {1206, 7551}
2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
C11 and C15 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
793D Off-Highway Truck/Tractor Electronic Control Module (Road Analysis Control) - Remove and Install
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Remove
PM-201 Cold Planer Compressed Air System - Inspect