The Sleeve Bearings That Are Used In Some Idler Gears, Cluster Gears, Cage Assemblies, And Adapter Assemblies Are Now Available For Parts Service {1206, 7551}
- Off-Highway Truck/Tractor:
- 785C (S/N: 1HW1-UP; APX1-UP; 5AZ1-UP)
- 789C (S/N: 2BW1-UP)
- 793B (S/N: 1HL1-UP)
- 793C (S/N: 4AR1-UP; ATY1-UP; 4GZ1-UP)
- 797 (S/N: 5YW1-UP)
The sleeve bearings that are used in the gears, the cages, and the adapters that are in the front gear groups and accessory drive groups on the engines in the above machines are now available for parts service. The table identifies the components and the applicable sleeve bearings. The inside diameter of the installed sleeve bearing is also provided in the table.
Note: After a sleeve bearing is installed, some machining may be needed in order to achieve the inside diameter that is required. The inside diameter that is required is identified in the table.
Show/hide table
Component     | Bearing     | Inside Diameter of the Installed Bearing     | Max Ra of the Bearing     | Machine     |
---|---|---|---|---|
136-3234 Idler Gear (1)     | 136-3244     | 112.142 ± 0.010 mm (4.4150 ± 0.0004 inch)     |
0.8 micrometer (32 microinch)     |
797     |
137-8336 Idler Gear (2)     | 137-8338     | 137.872 ± 0.063 mm (5.4280 ± 0.0025 inch)     |
||
146-7393 Cluster Gear Assembly (2)     | 146-7395     | 120.009 ± 0.063 mm (4.7248 ± 0.0025 inch)     |
||
146-7404 Cage As (2)     | 146-7411     | 63.539 ± 0.036 mm (2.5015 ± 0.0014 inch)     |
||
146-7408 Adapter (2)     | 146-7411     | 63.539 ± 0.036 mm (2.5015 ± 0.0014 inch)     |
||
163-2600 Cage As (3)     | 137-8298     | 63.500 ± 0.038 mm (2.5000 ± 0.0015 inch)     |
785C, 789C, 793B, 793C | |
141-7120 Cage As (4)     | 137-8298     | 63.500 ± 0.038 mm (2.5000 ± 0.0015 inch)     |
||
141-7130 Adapter (5)     | 137-8299     | 63.500 ± 0.038 mm (2.5000 ± 0.0015 inch)     |
Show/hide table
( 1 ) | This idler gear is used in the 136-3230 Front Gear Gp and the 164-7710 Accessory Drive Gp . |
( 2 ) | This component is part of the 137-8335 Accessory Drive Gp . |
( 3 ) | This cage assembly is used in several accessory drive groups. |
( 4 ) | This cage assembly is used in the 121-5710 Accessory Drive Gp . |
( 5 ) | This adapter is used in several accessory drive groups. |
Caterpillar Information System:
PM-201 Cold Planer Circuit Breakers - Reset
120M, 12M, 140M and 160M Motor Graders Machine Systems Governor (Air Compressor) - Test and Adjust
120M, 12M, 140M and 160M Motor Graders Machine Systems Step Group
120M, 12M, 140M and 160M Motor Graders Machine Systems Front Axle
14L Motor Grader Machine Systems Circle
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 2119 - FMI 03
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Fuel Tank - Remove
120M, 12M, 140M and 160M Motor Graders Machine Systems Blade Lift
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Left Drag Conveyor and Right Auger Conveyor) - Install
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Assemble
2005/02/07 A Correction to A New Engine Coolant Heater Is Available {1383}
793D Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve - Install
2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
C11 and C15 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
793D Off-Highway Truck/Tractor Electronic Control Module (Road Analysis Control) - Remove and Install
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Feeder Drive Shaft Group - Remove
PM-201 Cold Planer Compressed Air System - Inspect
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Fuel Tank - Install
PM-201 Cold Planer Compressed Air System Air Filter Element - Clean/Replace
PM-201 Cold Planer Compressed Air System Lubricator Oil Level - Check
PM-201 Cold Planer Conveyor Swing Cylinder Pins - Lubricate
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Final Drive - Assemble
793D Off-Highway Truck/Tractor Electronic Control Module (VIMS Main Module) - Remove and Install
PM-201 Cold Planer Engine Oil Level - Check