Final Drive - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7574     | Link Bracket     | 2     |
B     | 9U-5343     | Guide Stud M24 x 3     | 2     |
- Install Tooling (B) into final drive (1A). Tooling (B) should be installed 180 degrees from each other. Install a suitable lifting device with Tooling (A) and install the final drive, as shown. The weight of the final drive with the travel motor is approximately 576 (1270 lb).
Show/hide table
Illustration 1 | g01019812 |
- Install eighteen mounting bolts (7). Remove Tooling (B) and install the last two mounting bolts (7). Tighten the mounting bolts to a torque of 900 ± 100 N·m (660 ± 75 lb ft).
Show/hide table
Illustration 2 | g01019813 |
- Connect hose assemblies (3), (4), (5), and (6) to the travel motor.
Show/hide table
Illustration 3 | g01019385 |
- Install cover (2). Use two people in order to install the cover. The weight of cover (2) is approximately 41 kg (90 lb). Install bolts (1) .
Show/hide table
Illustration 4 | g01019383 |
End By: Connect the track assembly. Refer to Disassembly and Assembly, "Track - Connect".
Caterpillar Information System:
988H and 988K Wheel Loaders Power Train Transmission Planetary - Assemble
2005/02/21 Information Release Memo, PELJ0481 , "Product Line Expansion for Caterpillar Low and Medium Pressure Hose and Coupling Products" {5057}
3054E Engines for Caterpillar Built Machines Lubrication System
3054E Engines for Caterpillar Built Machines Cooling System
120M, 12M, 140M and 160M Motor Graders Machine Systems Drawbar
C15 and C18 Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
R2900G Load Haul Dump Steering System Relief Valve (Pilot)
C11 and C15 Engines for Caterpillar Built Machines Electrical Power Supply Circuit - Test
3126B Engines Engine Oil Pressure - Test
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 1964 - FMI 00
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Final Drive - Remove
PM-201 Cold Planer Towing the Machine
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Final Drive - Disassemble
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201} Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
793D Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 1964 - FMI 01
793D Off-Highway Truck Power Train Drive Shaft Guard (Front) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Power Train Transmission, Input Transfer Gears and Output Transfer Gears - Remove
C11 and C15 Engines for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test
793D Off-Highway Truck Power Train Drive Shaft Guard (Rear) - Remove and Install
793D Off-Highway Truck Power Train Relief Valve (Torque Converter Outlet) - Remove and Install
267B, 277B and 287B Multi Terrain Loaders Power Train Piston Pump (Hydrostatic) - Remove
267B, 277B and 287B Multi Terrain Loaders Power Train Piston Pump (Hydrostatic) - Install
C11 and C15 Engines for Caterpillar Built Machines Digital Sensor Supply Circuit - Test