Comfort Seat Air Suspension with System Air - Assemble
组装步骤
- 安装螺栓 (43) 以便把弹簧组件 (34) 连接到交叉式臂架组件 (18) 上。 把软管组件 (42) 连接到弹簧组件 (34) 上。
Show/hide table
图 1 | g01109843 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装轴 (40) 以便把肘节组件 (41) 连接到交叉式臂架组件 (18) 上。 把轴 (40) 上的 2 个螺母拧紧至扭矩为 15 ± 3 N·m (11 ± 2 lb ft)。
Show/hide table
图 2 | g01109794 |
- 安装轴组件 (38) 和 (39) ,以便将栓系带 (37) 和交叉式臂架组件 (18) 连接到壳体组件 (22) 上。 把轴组件 (38) 和 (39) 的螺母拧紧至扭矩为 20 ± 5 N·m (15 ± 4 lb ft)。 安装止块,以防止交叉式臂架组件 (18) 倒下。
Show/hide table
图 3 | g01109838 |
- 安装螺钉 (36) 以便把壳体组件 (22) 连接到弹簧组件 (34) 上。
Show/hide table
图 4 | g01109837 |
Show/hide table
图 5 | g01109778 |
- 安装轴 (33) 以便把肘节组件 (35) 连接到交叉式臂架组件 (18) 上。 把轴 (33) 上 2 个螺母拧紧至扭矩为 15 ± 3 N·m (11 ± 2 lb ft)。
- 将轴承 (27) 和 (30) 安装到减振器 (20) 上。
Show/hide table
图 6 | g01109816 |
Show/hide table
图 7 | g01109812 |
Show/hide table
图 8 | g01109763 |
- 安装螺栓 (24) 和卡箍 (23) 以便将支架 (25) 和电缆组件 (11) 连接到减振器 (20) 上。
- 安装防松垫圈 (26) 和垫圈 (31) 。 安装螺栓 (19) 和 (21) ,以便将减振器 (20) 连接到交叉式臂架组件 (18) 和壳体组件 (22) 上。 安装螺母 (29) 和锁紧螺母 (32) 。 取下止块。
- 将软管组件 (17) 连接到气阀 (8) 上。
Show/hide table
图 9 | g01109755 |
- 把气阀 (8) 安置在上部壳体组件 (16) 上。 把上部壳体组件 (16) 在座椅上定位。
Show/hide table
图 10 | g01109803 |
- 安装轴组件 (15) 。 把轴组件 (15) 的螺母拧紧至扭矩为 20 ± 5 N·m (15 ± 4 lb ft)。
Show/hide table
图 11 | g01109900 |
- 安装螺栓 (9) 以连接支架 (10) 。
Show/hide table
图 12 | g00896818 |
- 安装螺栓 (13) 以将杆 (14) 固定到支架 (10) 上。
- 安装螺栓 (12) 以便把电缆组件 (11) 固定到杆 (14) 上。
- 把板件 (5) 在座椅上定位。 安装防松垫圈 (6) 和螺母 (7) ,使气阀 (8) 在座椅上固定。 拧紧调整按钮 (1) 的调整螺钉, 使调整按钮 (1) 固定在气阀 (8) 上。
Show/hide table
图 13 | g00896809 |
- 安装螺栓 (3) 以将接头 (4) 固定到座椅上。
- 把座圈 (2) 装到座椅上。
Show/hide table
图 14 | g00896756 |
Caterpillar Information System:
TK370, TK371, TK380 and TK381 Wheel Feller Bunchers Machine Systems Gear Pump (Hydraulic Oil Cooler)
Caterpillar Comfort Series Seat with Three-Point Operator Restraint Comfort Seat Air Suspension with System Air - Disassemble
Comfort Series Seat For Caterpillar Machines Comfort Seat with Front Controls - Assemble
Comfort Series Seat For Caterpillar Machines Comfort Seat with Front Controls - Disassemble
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper - Check
CB-434D and CB-434D Series XW Vibratory Compactors Engine Supplement Alternator - Remove and Install
THP10 Series II and THP24S Series II Access Platform for Series B Telehandlers Guards - Operator Protection
Reworking Bores on 797, 797B and 797F Truck Frames, Bodies, and Axle Housings{3260, 3260, 7000, 7000, 7050, 7050, 7051, 7051, 7258, 7258} Reworking Bores on 797, 797B and 797F Truck Frames, Bodies, and Axle Housings{3260, 3260, 7000, 7000, 7050, 7050, 7051, 7051, 7258, 7258}
Procedure to Update the All Wheel Drive Pressure Sensor On Tier I and Tier II Motor Graders{4352} Procedure to Update the All Wheel Drive Pressure Sensor On Tier I and Tier II Motor Graders{4352}
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Test
797 Off-Highway Truck Safety Messages
CB-434D and CB-434D Series XW Vibratory Compactors Engine Supplement Air Cleaner - Remove and Install
2004/07/26 Special Instructions Are No Longer Announced In the Service Magazine {1000, 7000}
CB-434D and CB-434D Series XW Vibratory Compactors Engine Supplement Electric Starting Motor - Remove and Install
CB-434D and CB-434D Series XW Vibratory Compactors Engine Supplement Engine Enclosure - Remove and Install
R2900G Load Haul Dump Power Train Oscillating Axle (Rear) - Remove
THP10 Series II and THP24S Series II Access Platform for Series B Telehandlers Equipment Lowering with Loss of Hydraulic Power
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0817 - FMI 04
797B Off-Highway Truck Brake Accumulator (Service) - Disassemble
797B Off-Highway Truck Brake Accumulator (Service) - Assemble
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 1639 - FMI 02
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 1639 - FMI 09
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 1960 - FMI 09
Installation of Conventional Duo-Cone Seals{7561} Installation of Conventional Duo-Cone Seals{7561}