Compactor Wheel - Remove
Removal Procedure for the 825H Soil Compactor
Start By:
- Connect the steering frame lock.
- Release the hydraulic system pressure.
- Remove the front fenders.
- Remove the rear cleaner bar.
Note: The following procedure is for the removal of one front wheel.
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A(1) | 9U-7536 | Lift Stand | 2 |
447-0910 | Electric Hydraulic Pump (115 V) | 1 | |
447-0911 | Electric Hydraulic Pump (230 V) | 1 | |
9U-7531 | Tube As | 1 | |
OR | |||
A1 | 504-9791 | Lift Gp (60Hz)(2) | 2 |
504-9793 | Lift Gp (50Hz)(3) | 2 |
Show/hide table
(1) | Use Tooling (A) or (A1) based on requirements. |
(2) | Operating-voltage (480V - 240V) |
(3) | Operating-voltage (400V - 200V) |
- Place wood blocks in front of the rear tires and behind the rear tires.
Show/hide table
Illustration 1 g01084950 - Place a wood block between the top of the rear axle and the frame, as shown.
Show/hide table
Illustration 2 g01084932 - Attach a suitable lifting device to the push arm. The weight of the push arm and the tilt cylinder is approximately
474 kg (1045 lb) . Remove bolts (1). Remove cap (2). Disconnect the rod end of cylinder (3) from the blade. Remove bolts (6) and remove pin (7). Disconnect hose assemblies (4) and (5).Show/hide tableIllustration 3 g01084939 - Remove bolts (10), cap (9), and shims (8) from the rear of the push arm. Remove the push arm.
Show/hide table
Illustration 4 g06393759 For Tooling (A) - Use Tooling (A) to raise the front of the machine until the wheels are off the ground.
Show/hide table
Illustration 5 g06393764 For Tooling (A1) - Use Tooling (A1) to raise the front of the machine until the wheels are off the ground. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
- Attach a suitable lifting device to the wheel and the rim. The combined weight of the wheel and the rim for the 825H Soil Compactor is approximately
1978 kg (4360 lb) . Remove bolts (12) and the washers from the rim. - Remove wheel (11) and the rim as a unit.
- Place a wood block between the top of the rear axle and the frame, as shown.
- Place Tooling (A) (not shown) or (A1) ( not shown) under the rear frame of the machine. Use Tooling (A) or (A1) to raise the machine until the wheel is off the ground. Lock Tooling (A) in position with a locking ring. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Show/hide table
Illustration 7 g00537508 - Attach a suitable lifting device to the wheel and the rim. The combined weight of the wheel and the rim for the 825H Soil Compactor is approximately
1978 kg (4360 lb) . - Remove nuts (1) from the wheel.
Show/hide table
Illustration 8 g00537516 The 826H Landfill Compactor is shown. - Remove the wheel and the rim (2) from the machine.
Show/hide table
Illustration 6 | g01084950 |
Removal Procedure for the 826H Landfill Compactor
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A(1) | 9U-7536 | Lift Stand | 2 |
447-0910 | Electric Hydraulic Pump (115 V) | 1 | |
447-0911 | Electric Hydraulic Pump (230 V) | 1 | |
9U-7531 | Tube As | 1 | |
A1 | OR | ||
504-9791 | Lift Gp (60Hz)(2) | 2 | |
504-9793 | Lift Gp (50Hz)(3) | 2 |
Show/hide table
(1) | Use Tooling (A) or (A1) based on requirements. |
(2) | Operating-voltage (480V - 240V) |
(3) | Operating-voltage (400V - 200V) |
Note: The following procedure is for the removal of one front wheel.
- Place wood blocks in front of the wheels and behind the wheels that are not being removed.
Show/hide table
Illustration 9 g01084950 - Place a wood block between the top of the rear axle and the frame, as shown.
- Place Tooling (A) (not shown) or (A1) (not shown) under the loader frame of the machine. Use Tooling (A) or (A1) to raise the machine until the wheel is off the ground. Lock Tooling (A) in position with a locking ring. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Show/hide table
Illustration 10 g00537508 - Attach a suitable lifting device to the wheel and the rim. The combined weight of the wheel and the rim for the 826H Landfill Compactor can weigh as much as
2753 kg (6070 lb) . - Remove nuts (1) from the wheel.
Show/hide table
Illustration 11 g00537516 - Remove wheel (2) from the machine.
Caterpillar Information System:
AP-800D and BG-230D Asphalt Pavers Equipment Lowering with Engine Stopped
2004/06/28 Revised Special Instruction, REHS1634, "Reworking of Latching Transmission to Nonlatching Transmission" is Available {3030}
TH580B Telehandler Hydraulic System Boom Chain - Clean/Inspect/Lubricate
834H Wheel Dozer and 836H Landfill Compactor Power Train Torque Converter Stall - Test
834H Wheel Dozer and 836H Landfill Compactor Power Train Torque Converter Lockup Clutch Pressure - Test
834H Wheel Dozer and 836H Landfill Compactor Power Train Torque Converter Impeller Clutch Pressure - Test
446D Backhoe Loader Machine Systems Pump Drive - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Power Train Fill Time for the Transmission Clutch (Electronic Technician) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Power Train Engagement Pressure for the Transmission Clutch (Electronic Technician) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Power Train Engagement Pressure for the Lockup Clutch of the Torque Converter (Electronic Technician) - Calibrate
834H Wheel Dozer and 836H Landfill Compactor Power Train Position Sensor (Left Brake Pedal) (Electronic Technician) - Calibrate
PS-150C Pneumatic Compactor Propel System Parking Brake - Test
446D Backhoe Loader Machine Systems Hoe Bucket - Remove and Install
2004/10/25 New Plates that Eliminate Interference Problems on Machines with a Grapple Bucket are Available {5498, 6704}
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train Compactor Wheel - Install
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
TK370, TK371, TK380 and TK381 Wheel Feller Bunchers Machine Systems Winch
PS-360C Paving Compactor Indicators and Gauges - Test
AP-800D and BG-230D Asphalt Pavers Machine Systems Machine Preparation for Troubleshooting
AP-800D and BG-230D Asphalt Pavers Hydraulic Screed Counterbalance System
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train Cleaner Bar - Remove
PS-150C Pneumatic Compactor Propel System Parking Brake Release Pressure - Test
CB-334E and CB-335E Vibratory Compactors Machine Systems Front Frame and Rear Frame - Connect