Usage:
FLUID SPILLAGE CONTAINMENT
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates.
1. Remove eight bolts(1) and remove guard (2).
2. Loosen bolts (3) and remove belt (4) from pulley (5) of the raw water pump.
3. Loosen hose clamps and disconnect hose (6). Remove two bolts (7) and remove the raw water pump.
NOTE: Install in the reverse order.
Disassemble Raw Water Pump
NOTE: This is Typical Example of a Raw Water Pump Disassembly and Assembly.
Start By:
a. remove raw water pump
1. Loosen bolt (2) and remove pulley (1) and the key from the pump shaft.
2. Remove bracket (3), nipple (5), elbows (4), (6) and (7) from the raw water pump body.
3. Remove screws (8), cover (9) and the gasket.
4. Remove spacer (10) and impeller assembly (11) from the pump.
5. Remove screw (12) to remove cam (13) from body assembly (14).
6. Remove plate (15) from body assembly (14).
7. Turn the pump assembly over and remove seal (17). Use Tool (A) to remove ring (16).
8. Turn the pump assembly over and use a press to remove the shaft assembly and bearing from body assembly (14).
9. Use Tool (B) and remove the ring that holds bearing (19) to shaft assembly (18). Use Tool (C) and a press to push shaft assembly (18) out of bearing (19) as shown. Do notremove the bronze bushing that is fastened to the shaft.
10. Remove seal (20) from body assembly (14).
11. Remove the ceramic seal and grommet of seal assembly (21). Use Tool group (D) and a press to push the carbon half of seal assembly (21) out of body assembly (14) toward the drive end as shown.
Assemble Raw Water Pump
1. Put a small amount of clean grease on the lip of inner bearing seal (20) and install it in body assembly (14). Make sure the lip of the seal is away from the bearing bore as shown.
2. Use Tool (C) as support for the inner race of bearing (19) and use a press to push shaft assembly (18) in the bearing.
3. Use Tool (B) to install the ring that holds bearing (19) in position. Make sure the flat side of the ring is toward the bearing.
4. Use a press and a piece of pipe 44.5 mm (1.75 in) Diameter x 101.6 mm (4.00 in) Longto install bearing (19) and the shaft assembly in body assembly (14) as shown.
5. Use Tool (A) to install ring (16) in body assembly (14) with the flat side of the ring toward the bearing.
6. Make sure the rubber grommet is in position in ceramic seal seat (22). Put clean water on the grommet and install seat (22) on the pump shaft with the grommet toward the bearing.
7. Install seal (23) on the pump shaft with the carbon face toward seat (22).
8. Use Tool (E) and a press to install seal (23) and seat (22) until seal (23) is even with the bottom of the impeller bore in body assembly (14).
9. Make an alignment of the opening (slot) in plate (15) with the dowel in body assembly (14) and install plate in the body assembly.
10. Put Permatex on the top of cam (13) and on the threads of screw (12). Put cam (13) in position and install screw (12).
11. Put a small amount of 5P-0960 Multipurpose Type Greaseon the end surfaces of impeller (11) and on the impeller bore in the body assembly. Push down and turn to install impeller (11) in the body assembly. Install spacer (10).
12. Put the gasket and cover (9) on the body assembly and install screws (8).
13. Put a small amount of clean grease on the lip of seal (17). Install seal (17) until it is even with the surface of body assembly (14). Make sure the lip of the seal is toward the outside.
14. Install elbows (4), (6) and (7), nipple (5) and bracket (3) on the pump body.
15. Put the key and pulley (1) in position on the pump shaft and tighten screw (2).
End By:
a. install raw water pump