Control Valve (Work Tool) - Disassemble
开始:
- 拆下控制阀。 请参阅拆解和装配, "控制阀(作业机具)- 拆卸"。
- 拆下电磁阀 (1)。 拆下接头 (2)。 拆下接头 (3)。
Show/hide table
图 2 g00902740 - 拆下 O 形密封圈 (4)。 拆下 O 形密封圈 (5)。 从电磁阀 (1) 上拆下 O 形密封圈 (6)。
Show/hide table
图 3 g00902556 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下螺塞 (7) 和 O 形密封圈。
Show/hide table
图 4 g00902725 - 拆下弹簧 (9)。 拆下单向阀 (8)。
- 对其余的螺塞重复步骤 3 至 4。
Show/hide table
图 5 g00902568 注: 观察接头和蓄能器的方位。
- 拆下接头 (10)。 卸下接头 (11)。 拆下适配器 (12)。 拆下接头和蓄能器 (13)。
Show/hide table
图 6 g00902570 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下螺塞 (14) 和 O 形密封圈。
Show/hide table
图 7 g00902622 - 卸下弹簧 (15)。
- 对其余的螺塞重复步骤 7 至 8。
Show/hide table
图 8 g00902652 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下盖 (16) 和 O 形密封圈。
Show/hide table
图 9 g01067199 - 拆下安全阀 (17)。
Show/hide table
图 10 g01067200 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下螺塞 (17A) 和 O 形密封圈。
Show/hide table
图 11 g00902889 - 卸下弹簧 (18)。 拆下滤网和垫圈 (19)。
Show/hide table
图 12 g00902977 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下滑阀 (20)。 拆下螺塞、O 形密封圈和弹簧 (21)。
Show/hide table
图 13 g00902978 - 拆下滑阀 (22)。
Show/hide table
图 14 g00902979 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下盖 (23) 和 O 形密封圈。
Show/hide table
图 15 g00902980 - 拆下弹簧 (24)。
Show/hide table
图 16 g00902985 - 拆下接头 (25)。 拆下安全阀 (26)。 拆下滑阀 (27)。
Show/hide table
图 17 g00902884 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 加热螺栓 (31)。 拆下螺栓 (31)。 拆下垫圈 (30)。 拆下弹簧 (29)。 拆下垫圈 (28)。
Show/hide table
图 18 g00902987 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 拆下盖 (32) 和 O 形密封圈。
Show/hide table
图 19 g00902988 - 拆下弹簧 (33)。 拆下单向阀 (34)。
Show/hide table
图 1 | g00902554 |
Caterpillar Information System:
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0623 - FMI 03
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Remove
16H Motor Grader Power Train Wheel and Tire (Rear) - Remove and Install
267B, 277B and 287B Multi Terrain Loaders Machine Systems Gear Motor - Install
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center General Information
12M Motor Grader Backup Alarm
2004/04/19 Special Instruction, REHS2144, "Installation of Heavy Duty Brakes" Is Available {3278, 4251}
R1300G Load Haul Dump 3306 Engine Supplement Radiator - Install
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
Bench Test Procedure for Hydraulic Piston Pumps {3203} Bench Test Procedure for Hydraulic Piston Pumps {3203}
Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197} Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197}
16H Motor Grader Power Train Drive Chain - Remove
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center Visual Inspection
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Lift Arm
AS2251 and AS2301 Asphalt Screed Fuel Pump Control
16H Motor Grader Power Train Drive Chain - Install
C27 and C32 Generator Set Engines Engine Design
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Control Valve (Work Tool) - Assemble
16H Motor Grader Power Train Service Brake (Wheel Spindle) - Remove
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 03
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 04
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 08