Control Valve (Work Tool) - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件名称 | 数量 |
A | 155-0695 | 螺纹锁固胶 | 1 |
- 安装单向阀 (34)。 安装弹簧 (33)。
Show/hide table
图 2 g00902987 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装盖 (32) 和 O 形密封圈。 拧紧盖至扭矩为
25 ± 3 N·m (18 ± 2 lb ft) 。Show/hide table图 3 g00902884 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装垫圈 (28)。 安装弹簧 (29)。 安装垫圈 (30)。 将工具 (A) 涂抹到螺栓 (31) 的螺纹上。 安装螺栓 (31)。 将螺栓 (31) 拧紧至扭矩为
10 ± 1 N·m (89 ± 9 lb in) 。Show/hide table图 4 g00902985 - 安装滑阀 (27)。 安装安全阀 (26)。 将安全阀拧紧至扭矩为
10 ± 1 N·m (7 ± 1 lb ft) 。 安装接头 (25)。Show/hide table图 5 g00902980 - 安装弹簧 (24)。
Show/hide table
图 6 g00902979 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装盖 (23) 和 O 形密封圈。 拧紧盖至扭矩为
122 ± 12 N·m (90 ± 9 lb ft) 。Show/hide table图 7 g00902978 - 安装滑阀 (22)。
Show/hide table
图 8 g00902977 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装螺塞、O 形密封圈和弹簧 (21)。 拧紧螺塞至扭矩为
65 ± 7 N·m (48 ± 5 lb ft) 。 安装滑阀 (20)。Show/hide table图 9 g00902889 - 安装滤网和垫圈 (19)。 安装弹簧 (18)。
Show/hide table
图 10 g01067199 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装螺塞 (17A) 和 O 形密封圈。 拧紧螺塞至扭矩为
65 ± 7 N·m (48 ± 5 lb ft) 。Show/hide table图 11 g01067200 - 安装安全阀 (17A)。 拧紧安全阀至扭矩为
45 ± 5 N·m (33 ± 4 lb ft) 。Show/hide table图 12 g00902652 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装盖 (16) 和 O 形密封圈 (16)。 拧紧盖至扭矩为
122 ± 12 N·m (90 ± 9 lb ft) 。Show/hide table图 13 g00902622 - 安装弹簧 (15)。
Show/hide table
图 14 g00902570 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装螺塞 (14) 和 O 形密封圈。 拧紧螺塞至扭矩为
65 ± 7 N·m (48 ± 5 lb ft) 。Show/hide table图 15 g00902568 注: 观察接头和蓄能器的方位。
- 安装接头和蓄能器 (13)。 安装接头 (12)。 拧紧接头至扭矩为
150 ± 15 N·m (111 ± 11 lb ft) 。 安装接头 (11)。 拧紧接头 (11) 至扭矩为150 ± 15 N·m (111 ± 11 lb ft) 。 安装接头 (10)。Show/hide table图 16 g00902725 - 安装单向阀 (8)。 安装弹簧 (9)。
Show/hide table
图 17 g00902556 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装螺塞和 O 形密封圈 (7)。 拧紧螺塞至扭矩为
65 ± 7 N·m (48 ± 5 lb ft) 。 - 对其余的螺塞重复步骤 16 至 17。
Show/hide table
图 18 g00902740 - 安装 O 形密封圈 (4)。 安装 O 形密封圈 (5)。 将 O 形密封圈 (6) 安装到电磁阀 (1) 上。
Show/hide table
图 19 g00902554 - 安装接头 (3)。 安装接头 (2)。 安装电磁阀 (1)。 拧紧电磁阀至扭矩为
39 ± 4 N·m (29 ± 3 lb ft) 。
Show/hide table
图 1 | g00902988 |
结束:
- 安装控制阀。 请参阅拆解和装配, "控制阀(作业机具)- 安装"。
Caterpillar Information System:
C27 and C32 Generator Set Engines Engine Design
16H Motor Grader Power Train Drive Chain - Install
AS2251 and AS2301 Asphalt Screed Fuel Pump Control
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Lift Arm
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center Visual Inspection
16H Motor Grader Power Train Drive Chain - Remove
Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197} Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197}
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Control Valve (Work Tool) - Disassemble
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0623 - FMI 03
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Remove
16H Motor Grader Power Train Service Brake (Wheel Spindle) - Remove
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 03
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 04
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1957 - FMI 08
120M and 12M Motor Graders Steering Frame Lock
SCJ and 8SC Series Alternators Alternator - Assemble
2004/04/26 Accelerator Hinge Pin Instructions Are Now Included with Parts Kit {1276}
16H Motor Grader Power Train Service Brake (Wheel Spindle) - Install
267B, 277B and 287B Multi Terrain Loaders Machine Systems Fuel Tank - Remove and Install
12M Motor Grader Seat
10-20B and 8-16B EXTEND A MAT SCREEDS Deflector Plate Adjustment (Strike-Off)
2004/05/03 New Transmission Solenoid Valve Groups Are Now Being Used {3174}