Heater Coil - Remove
拆卸步骤
开始:
- 拆下座椅。 请参考拆解和装配, "座椅 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
 |
在工作温度下，发动机冷却液是热的，并且带有压力。 蒸汽还会引起人身伤害。 只有在发动机已关闭且加注口盖冷却到可徒手触摸后，才能检查冷却液液位。 缓慢卸下加注口盖，释放其中压力。 冷却系统添加剂含碱。 应避免皮肤和眼睛与其接触，以防造成人身伤害。 |
注: 为便于安装，在所有管路、软管、导线和管子上做出识别标记。 插接所有管路、软管和管子。 这将有助于防止液体泄漏和污染物进入系统。
- 从冷却系统将冷却液排入合适的容器中。
- 拆下固定盖 (2) 的螺钉 (1) 。
Show/hide table
 | |
| 图 1 | g00284950 |
- 抬起盖 (2) 。 断开线束组件 (3) 。 拆下罩盖 (2) 。
Show/hide table
 | |
| 图 2 | g00460918 |
- 将橡胶垫 (4) 和绝缘层从驾驶室地板上拆下。
- 卸下螺栓 (5) 。 拆下盖 (6) 。
Show/hide table
 | |
| 图 3 | g01067156 |
- 拆下盖 (7) 。
Show/hide table
 | |
| 图 4 | g00284954 |
- 拆下控制旋钮 (8) 和空气滤清器 (9) 。
Show/hide table
 | |
| 图 5 | g00284955 |
- 拆下螺栓和螺钉 (11) 。 拆下盖 (10) 。
Show/hide table
 | |
| 图 6 | g00284956 |
- 拆下密封垫 (12) 。
Show/hide table
 | |
| 图 7 | g00284959 |
- 将毛细管 (15) 从蒸发器线圈 (13) 拉出。 小心地重新安置毛细管 (15) ，使其远离线圈组件。
Show/hide table
 | |
| 图 8 | g00460919 |
- 断开软管组件 (14) 。
- 将密封件 (17) 和螺栓 (18) 从线圈组件的两端拆下。
Show/hide table
 | |
| 图 9 | g00460920 |
- 拆下加热器线圈组件 (16) 。
Caterpillar Information System:
16H Motor Grader Power Train Wheel and Tire (Rear) - Remove and Install
267B, 277B and 287B Multi Terrain Loaders Machine Systems Gear Motor - Install
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center General Information
12M Motor Grader Backup Alarm
2004/04/19 Special Instruction, REHS2144, "Installation of Heavy Duty Brakes" Is Available {3278, 4251}
R1300G Load Haul Dump 3306 Engine Supplement Radiator - Install
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
Bench Test Procedure for Hydraulic Piston Pumps {3203} Bench Test Procedure for Hydraulic Piston Pumps {3203}
Bench Test Procedure for Hydraulic Piston Pumps {3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps {3203, 5070}
267B, 277B and 287B Multi Terrain Loaders Machine Systems Gear Motor - Remove
2004/04/19 A New Valve Cover Seal and New Valve Cover Fasteners are Now Available {1107}
267B, 277B and 287B Multi Terrain Loaders Machine Systems Refrigerant Condenser and Mounting - Remove and Install
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0623 - FMI 03
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Install
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Control Valve (Work Tool) - Disassemble
Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197} Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197}
16H Motor Grader Power Train Drive Chain - Remove
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center Visual Inspection
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Lift Arm
AS2251 and AS2301 Asphalt Screed Fuel Pump Control
16H Motor Grader Power Train Drive Chain - Install
C27 and C32 Generator Set Engines Engine Design
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Control Valve (Work Tool) - Assemble