16H Motor Grader Power Train Caterpillar

Wheel and Tire (Rear) - Remove and Install

Usage:

16H ATS

Removal Procedure

Show/hide table

Table 1
Required Tools
Tool	Part Number	Part Description	Qty
A	283-1495	Stand Assembly	2
A	8S-7611	Tube	2
B⁽¹⁾	9U-7536	Lift Stand	1
B⁽¹⁾	4C-5749	Pump Dolly	1
B1	OR
	504-9791	Lift Gp (60Hz)⁽²⁾	1
	504-9793	Lift Gp (50Hz)⁽³⁾	1
C	425-0952	Chock	4

Show/hide table

⁽¹⁾	Use Tooling (B) or (B1) based on requirements.
⁽²⁾	Operating Voltage (240 - 480V)
⁽³⁾	Operating Voltage (200 - 400V)

Show/hide table

Follow the recommended procedure for removal and installation of tires and or wheel assemblies.
Ensure that the machine and tire and or wheel assembly are properly supported at all times.

Improper procedures that are used to remove and install tires and or wheel assemblies can result in personal injury or death.

Install the frame lock pin. Refer to Operation and Maintenance Manual, "Steering Frame Lock".
Show/hide table

Illustration 1 g01067157
Block the front wheels with Tooling (C).
Show/hide table

Illustration 2 g00924073

For Tooling (B).
Use Tooling (B) (not shown) to raise the rear wheels off the ground. Install Tooling (A) under the case. Repeat this step for the opposite side.
Show/hide table

Illustration 3 g00924073

For Tooling (B1).
Use Tooling (B1) (not shown) to raise the rear wheels off the ground. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (B1). Install Tooling (A) under the case. Repeat this step for the opposite side.
Show/hide table

Illustration 4 g01067178
Attach a suitable lifting device to wheel (1). The weight of wheel (1) is approximately 725 kg (1600 lb). Remove bolts (2) and wheel (1).

Installation Procedure

Show/hide table

Table 2
Required Tools
Tool	Part Number	Part Description	Qty
A	283-1495	Stand Assembly	2
A	8S-7611	Tube	2
B⁽¹⁾	9U-7536	Lift Stand	1
B⁽¹⁾	4C-5749	Pump Dolly	1
B1	OR
	504-9791	Lift Gp (60Hz)⁽²⁾	1
	504-9793	Lift Gp (50Hz)⁽³⁾	1
C	425-0952	Chock	4

Show/hide table

⁽¹⁾	Use Tooling (B) or (B1) based on requirements.
⁽²⁾	Operating Voltage (240 - 480V)
⁽³⁾	Operating Voltage (200 - 400V)

Show/hide table




Illustration 5	g01067178

Attach a suitable lifting device to wheel (1). The weight of wheel (1) is approximately 725 kg (1600 lb). Install wheel (1) and bolts (2). Tighten bolts (2) to a torque of 1455 ± 90 N·m (1073 ± 66 lb ft).
Show/hide table

Illustration 6 g00924073

For Tooling (B1)
Use Tooling (B1) (not shown) to raise the rear wheels off the ground. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (B1). Remove Tooling (A) under the case. Use Tooling (B1) to lower the rear wheels to the ground. Remove Tooling (B1). Repeat this step for the opposite side.
Show/hide table

Illustration 7 g00924073

For Tooling (B).
Use Tooling (B) (not shown) to raise the rear wheels off the ground. Remove Tooling (A) under the case. Use Tooling (B) to lower the rear wheels to the ground. Remove Tooling (B). Repeat this step for the opposite side.
Show/hide table

Illustration 8 g01067157
Remove Tooling (C).