General Information
Show/hide table
机器突然移动或释放气压或油压,可能对机器上或机器附近的人员造成伤亡。 为避免可能造成的伤亡,在测试和调整液压系统之前,遵照以下程序。 |
注: 机器上仅允许停留一位操作员。 让其他所有人员远离车辆或离开操作人员的视野。
- 把机器开到平整水平的地方。 把机器开到远离其他机器的地方。 把机器开到远离其他人员的地方。
- 将变速箱操纵杆移入空档位置。 关闭发动机。
- 启动停车制动器。
- 车轮前后都塞上车轮挡块。 请参阅拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
- 如有必要抬起卡车的卸载车斗,将固定电缆与卡车后部连接。 请参阅拆解和组装, "卡车车斗固定电缆 - 拆卸和安装"。
Show/hide table
图 1 | g01083655 |
与卸载车斗连接的固定电缆。 |
- 确保变速箱操纵装置处于空档位置。
- 在任何接头、软管或者部件上工作之前,确保释放所有机油压力。
目视检查是故障诊断与排除的第一步。 目视检查会确定可以快速修正的故障。
由于可能难以进行故障诊断与排除,所以在维修手册上列出了可能故障的列表。 为了维修某个故障,请参阅测试和调整, "故障诊断与排除部分"所列出的故障和可能原因。
故障和可能原因的列表只提供了可能存在的故障的位置和可能需要进行的修理。 有时还有除了列表之外的更多维修或其他需要的维修作业。 请记住:一个故障通常不会仅仅由单个零件引发。 一个故障通常是一个零件和其他零件关联产生。 该列表不能提供所有可能的故障和所有可能的原因。 维修人员必须要找到故障所在和故障源头。 维修人员必须进行必要的维修。
Caterpillar Information System:
12M Motor Grader Backup Alarm
2004/04/19 Special Instruction, REHS2144, "Installation of Heavy Duty Brakes" Is Available {3278, 4251}
R1300G Load Haul Dump 3306 Engine Supplement Radiator - Install
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
Bench Test Procedure for Hydraulic Piston Pumps {3203} Bench Test Procedure for Hydraulic Piston Pumps {3203}
Bench Test Procedure for Hydraulic Piston Pumps {3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps {3203, 5070}
267B, 277B and 287B Multi Terrain Loaders Machine Systems Gear Motor - Remove
2004/04/19 A New Valve Cover Seal and New Valve Cover Fasteners are Now Available {1107}
267B, 277B and 287B Multi Terrain Loaders Machine Systems Refrigerant Condenser and Mounting - Remove and Install
CB-214E, CB-224E and CB-225E Vibratory Compactors Propel System Piston Motors (Drum Propel and Wheel Propel)
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 08
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 04
267B, 277B and 287B Multi Terrain Loaders Machine Systems Gear Motor - Install
16H Motor Grader Power Train Wheel and Tire (Rear) - Remove and Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Remove
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0623 - FMI 03
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Heater Coil - Install
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Control Valve (Work Tool) - Disassemble
Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197} Installation and Removal of SystemOne Clamp Master {0729, 4157, 4170, 4197}
16H Motor Grader Power Train Drive Chain - Remove
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center Visual Inspection
416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Lift Arm
AS2251 and AS2301 Asphalt Screed Fuel Pump Control