Oscillating Axle (Rear) and Trunnion Support - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1U-7505 | 液压千斤顶 | 1 |
Show/hide table
 |
机器突然动作，会招致人员伤亡。 在调整传动系统时，机器可能会在前进或倒退方向上突然移动。 为了避免机器移动，确保把机器完全升离地面并进行适当地支撑。 确认测试和调整过程中工作区内无人和设备。 |
- 安装止推垫圈 (18) 、O 形密封圈 (17) 和套筒轴承 (16) 。
Show/hide table
 | |
| 图 1 | g00495708 |
Show/hide table
 | |
| 图 2 | g00495661 |
- 利用工具 (A) 和适当的起吊设备将摆动桥 (5) 移向机器。
- 将摆动桥 (5) 安装到机器上。 摆动桥的重量约为 658 kg (1450 lb)。
- 将螺栓 (15) 安装到耳轴上，如图所示。 将螺栓 (15) 上紧到 300 ± 40 N·m (221 ± 30 lb ft) 的扭矩。
Show/hide table
 | |
| 图 3 | g01062220 |
- 将螺栓 (14) 安装到机器上。 将螺栓 (14) 上紧到 300 ± 40 N·m (221 ± 30 lb ft) 的扭矩。
- 安装垫圈 (13) 和螺栓 (12) ，以便将摆动桥固定到机器上。
Show/hide table
 | |
| 图 4 | g00495678 |
- 连接黄油嘴 (11) 。
Show/hide table
 | |
| 图 5 | g00495671 |
- 安装止推垫圈 (10) 和 O 形密封圈 (9) 。
Show/hide table
 | |
| 图 6 | g00495665 |
- 安装板 (8) 、垫圈 (7) 和螺栓 (6) 。
Show/hide table
 | |
| 图 7 | g00495663 |
- 将适当的起吊设备固定到摆动桥的每侧上。
Show/hide table
| | |
| 图 8 | g00495661 |
- 利用工具 (A) 固定摆动桥 (5) 。
- 将适当的起吊设备固定到挡泥板的每侧上。 在起吊设备上施加稍许拉力。 挡泥板的重量约为 45 kg (100 lb)。
Show/hide table
 | |
| 图 9 | g00495637 |
Show/hide table
 | |
| 图 10 | g01055752 |
- 将螺栓 (3) 安装到挡泥板 (4) 上。
- 将螺栓 (1) 安装到挡泥板 (2) 上。
- 对于另一侧，重复步骤12 至14。
End By:
- 安装轮胎和轮缘。 请参阅 拆解和组装, "轮胎和轮辋 - 拆卸和安装"。
- 安装活塞马达。 请参阅 拆解和组装, "活塞马达（静液压）- 安装"。
Caterpillar Information System:
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Oscillating Axle (Rear) and Trunnion Support - Remove
2004/03/01 Improved Gasket for the Engine Oil Cooler {1378, 7555}
2004/03/08 Improved Gasket for the Engine Oil Cooler {1378, 7555}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Limited Slip Differential - Assemble - If Equipped
2004/03/15 Addition to Operation and Maintenance Manual , "Every 500 Service Hours or 3 Months" {4251}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Limited Slip Differential - Disassemble - If Equipped
CB-334E and CB-335E Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Wheel Propel) - Test
AP-655C and BG-2255C Asphalt Pavers Machine Systems Footshaft - Install
AP555E and BG555E Asphalt Pavers Machine Systems Footshaft - Assemble
AP555E and BG555E Asphalt Pavers Machine Systems Footshaft - Disassemble
AP-655C and BG-2255C Asphalt Pavers Machine Systems Footshaft - Remove
C13, C15, and C18 Generator Set Engines Engine Pressure Sensor Open or Short Circuit - Test
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Hydraulic Tank
2004/06/14 A New Hoist Pump Is Now Available {5083}
AP-1055B and BG-2455C Asphalt Pavers Equipment Lowering with Engine Stopped
AP-1000B and BG-260C Asphalt Pavers Equipment Lowering with Engine Stopped
966H and 972H Wheel Loaders Automatic Lubrication Grease Tank - Fill - Autolube - If Equipped
247B and 257B Multi Terrain Loaders Machine Systems Pilot Hydraulic System
3412E Engine for Caterpillar Built Machines CID 0190 FMI 02 Loss of Engine Speed Signal
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Fixed Axle (Front) - Remove
C13, C15, and C18 Generator Set Engines Engine Speed/Timing Sensor Circuit - Test
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Fixed Axle (Front) - Install
3412E Engine for Caterpillar Built Machines CID 0190 FMI 03 Engine Speed open/short to + batt
3412E Engine for Caterpillar Built Machines CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs