Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
- Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release".
Show/hide table
|
NOTICE |
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
|
Show/hide table
|
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
|
Show/hide table
|
|
|
Illustration 1 | g00842935 |
- Remove nuts (1) and the washers.
Show/hide table
|
|
|
Illustration 2 | g00842937 |
- Remove bolts (2) and the washers.
Show/hide table
|
|
|
Illustration 3 | g00842944 |
- Remove bolts (3) and the washers.
Show/hide table
|
|
|
Illustration 4 | g00842948 |
- Remove nuts (4) and the washers.
- Remove guard (5) .
Show/hide table
|
|
|
Illustration 5 | g00842953 |
- Remove bolts (7) and the washers. Place block assembly (6) aside.
Show/hide table
|
|
|
Illustration 6 | g00842956 |
- Remove brackets (9) from steering cylinder (8) .
Show/hide table
|
|
|
Illustration 7 | g00842963 |
- Disconnect grease line (11) .
- Remove bolt (10), the washer, and pin (12) from the head end of steering cylinder (8) .
Show/hide table
|
|
|
Illustration 8 | g00842969 |
- Disconnect grease line (15) .
- Remove bolt (14), the washer, and pin (13) from the rod end of steering cylinder (8) .
- Use two persons in order to carefully remove steering cylinder (8). The weight of steering cylinder (8) is approximately 34 kg (75 lb).
Disassembly and Assembly Information
Show/hide table
Table 1
Required Tools     |
Tool     |
Part Number     |
Part Description     |
Qty     |
A     |
127-4904     |
Repair Stand     |
1     |
B     |
7M-7456     |
Bearing Mount Compound     |
1     |
C     |
1P-1833     |
Adapter     |
1     |
4C-9633 |
Puller Stud     |
1     |
1A-1935 |
Full Nut     |
1     |
6V-3160 |
Double Acting Cylinder     |
1     |
9S-5565 |
Pin Puller Sleeve As     |
1     |
3S-6224 |
Electric Hydraulic Pump Gp     |
1     |
D     |
1P-0808     |
Multipurpose Grease     |
1     |
E     |
1P-0510     |
Driver Gp     |
1     |
F     |
9U-7868     |
Spanner Wrench     |
1     |
127-8064 |
Adjustable Plate     |
1     |
G     |
195-4609     |
Seal Pick     |
1     |
Show/hide table
|
|
|
Illustration 9 | g00951818 |
The callouts in this graphic reference each of the following steps. |
(1) Apply Tooling (B) to the seal groove prior to assembling the wiper seal.
(2) Lubricate sealing lips with a thin covering of the lubricant that is being sealed.
(3) Torque for head ... 600 ± 130 N·m (440 ± 95 lb ft)
(4) Use a 46 mm socket to remove the bolt.
Note: Apply Tooling (D) to the threads.
The bottom face includes both ends of the articulation cylinders. Install the bearings to Depth (X) from the bottom face.
- Dimension (X) ... 7.14 ± 0.25 mm (0.281 ± 0.010 inch)
Note: Do not use an impact type driver to install the bearings.
Installation Procedure
Show/hide table
|
|
|
Illustration 10 | g00842969 |
- Use two people in order to install steering cylinder (8). The weight of steering cylinder (8) is approximately 34 kg (75 lb).
- Install pin (13), bolt (14), and the washer to the rod end of steering cylinder (8) .
- Connect grease line (15) .
Show/hide table
|
|
|
Illustration 11 | g00842963 |
- Install pin (10), bolt (12), and the washer to the head end of steering cylinder (8) .
- Connect grease line (11) .
Show/hide table
|
|
|
Illustration 12 | g00842956 |
- Install brackets (9) to steering cylinder (8) .
Show/hide table
|
|
|
Illustration 13 | g00842953 |
- Install block assembly (6). Install bolts (7) and the washers.
Show/hide table
|
|
|
Illustration 14 | g00842948 |
- Install guard (5) .
- Install nuts (4) and the washers.
Show/hide table
|
|
|
Illustration 15 | g00842944 |
- Install bolts (3) and the washers.
Show/hide table
|
|
|
Illustration 16 | g00842937 |
- Install bolts (2) and the washers.
Show/hide table
|
|
|
Illustration 17 | g00842935 |
- Install nuts (1) and the washers.
End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".