Coolant Temperature Sensor - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检查, 保养, 测试, 调整 and 维修发动机时,务必留心,确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将冷却液从冷却系统中排出,直到液位在冷却液温度传感器以下。 有关正确的排放步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 1 g03361008 - 将锁片 (2) 滑入解锁位置。 将线束组件 (3) 从冷却液温度传感器 (1) 上断开。
- 用深孔套筒将冷却液温度传感器 (1) 从缸盖上拆下。
- 将 O 形密封圈 (4) 从冷却液温度传感器 (1) 上拆下。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将一个新 O 形密封圈 (4) 安装到冷却液温度传感器 (1) 上。
注: 不要润滑 O 形密封圈。
- 用深孔套筒将冷却液温度传感器 (1) 安装到缸盖上。 将冷却液温度传感器拧紧至扭矩为
20 N·m (177 lb in) 。 - 将线束组件 (3) 连接到冷却液温度传感器 (1) 上。 将锁片 (2) 滑动到锁定位置。
- 加注冷却系统至正确液位。 有关正确的加注步骤,请参阅操作和保养手册, "冷却系统冷却液液位 - 检查"和操作和保养手册, "冷却系统冷却液 - 测试 / 添加"。
Show/hide table
图 2 | g03361008 |
Caterpillar Information System:
C7.1 Engines Connecting Rod Bearings - Remove - Connecting rods in position
C7.1 Engines Connecting Rod Bearings - Install - Connecting rods in position
C7.1 Engines Camshaft Gear - Remove and Install
C7.1 Engines Camshaft Bearings - Remove and Install
C7.1 Engines Camshaft - Remove and Install
C7.1 Engines Boost Pressure Sensor - Remove and Install
C7.1 Engines Alternator Belt - Remove and Install
C7.1 Engines Alternator - Remove
C7.1 Engines Alternator - Install
C7.1 Engines Air Compressor - Remove and Install - Twin Cylinder Air Compressor
C7.1 Engines Air Compressor - Remove and Install - Single Cylinder Air Compressor
C7.1 Engines Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C7.1 Engines Crankcase Breather - Install - Filtered Breather
C7.1 Engines Crankcase Breather - Remove - Filtered Breather
C7.1 Engines Crankcase Breather - Install - Unfiltered Breather
C7.1 Engines Crankcase Breather - Remove - Unfiltered Breather
C7.1 Engines Crankshaft - Install
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft Front Seal - Remove and Install
C7.1 Engines Crankshaft Gear - Remove and Install
C7.1 Engines Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 Engines Crankshaft Position Sensor - Remove and Install
C7.1 Engines Crankshaft Rear Seal - Install