Brake Accumulator - Install
安装步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 4C-8358 | 吊环螺栓 | 1 |
- 将工具 (A) 安装到制动蓄能器 (4) 的螺纹孔中。
Show/hide table
 | |
| 图 1 | g00341761 |
- 将适当的起吊设备和适当的吊索连接到工具 (A) 。 制动蓄能器 (4) 的重量约为 45 kg (100 lb)。
- 使用适当的起吊设备，小心地安装制动蓄能器 (4) 。
Show/hide table
 | |
| 图 2 | g00341755 |
- 安装卡箍螺栓 (5) 。
- 安装螺栓 (9) 。
Show/hide table
 | |
| 图 3 | g01448050 |
Show/hide table
 | |
| 图 4 | g01448045 |
- 将适配器 (8) 安装到制动蓄能器 (4) 的底部。
- 连接软管组件 (6) 和 (7) 。
- 将防尘盖 (3) 安装到制动蓄能器顶部。
Show/hide table
 | |
| 图 5 | g00341754 |
- 安装驾驶室左侧的盖板 (2) 。
Show/hide table
 | |
| 图 6 | g00341752 |
Show/hide table
 | |
| 图 7 | g00341753 |
- 加注转向系统和制动系统的液压油箱。 关于正确的程序，请参阅您机器的操作和保养手册。
- 检查制动蓄能器的充注。 关于正确的程序，请参阅您机器的操作和保养手册。
Show/hide table
 |
干燥氮气是唯一被认可用来给蓄能器充气的气体。 对蓄能器充氧气会引起爆炸。 使用带有标准 CGA（压缩气体产业协会，Compressed Gas Association, Inc.） 580 号接头的氮气罐可避免发生爆炸。 订购氮气罐时，务必订购带有 CGA 580 号接头的氮气罐。 不要依赖颜色代码或其它标识方法来区别氮气罐与氧气罐。 在任何情况下，都不能用同一个适配器把充氮总成连接到氮气、氧气或其它气体罐共用的阀出口上。 确保使用的是干燥氮气（纯度 99.8%）。 |
- 起动发动机并检查是否渗漏。 检查制动系统是否正常工作。
End By: 分离转向机架锁。 请参考 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
854K Wheel Dozer Machine Systems Brake Accumulator - Remove
Troubleshooting for 930G Wheel Loaders that Exhibit Dead Implement Functions{4320, 5050, 5057} Troubleshooting for 930G Wheel Loaders that Exhibit Dead Implement Functions{4320, 5050, 5057}
993K Wheel Loader Steering System Piston Pump (Steering) Margin Pressure - Test and Adjust
992K Wheel Loader Electrohydraulic System Pressure Reducing Valve Pressure for Dead Engine Pilot Supply (Engine OFF) - Test and Adjust
992K Wheel Loader and 854K Wheel Dozer Power Train Differential and Bevel Gear - Install
993K Wheel Loader Steering System General Information (Steering)
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0600 - FMI 04
Installation Instructions for the 301-6925 Joystick Control Gp (2-Function) and the 301-6926 Joystick Control Gp (3-Function) both with a transmission direction control switch{5063, 5705} Installation Instructions for the 301-6925 Joystick Control Gp (2-Function) and the 301-6926 Joystick Control Gp (3-Function) both with a transmission direction control switch{5063, 5705}
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0600 - FMI 03
Installation Instructions for the 301-6928 Secondary Steering Ar (Kit){4300, 4304, 4324, 4334, 5927} Installation Instructions for the 301-6928 Secondary Steering Ar (Kit){4300, 4304, 4324, 4334, 5927}
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0590 - FMI 09
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0590 - FMI 02
992K Wheel Loader Electrohydraulic System Pilot Control Actuator Pressure - Check
992K Wheel Loader Electrohydraulic System Electrical Input Components
992K Wheel Loader and 854K Wheel Dozer Power Train Differential and Bevel Gear - Disassemble
993K Wheel Loader Machine Systems Hydraulic Tank (Implement, Hydraulic Fan) - Disassemble
992K Wheel Loader Electrohydraulic System Electrical Output Components
854K Wheel Dozer Machine Systems Brake Control Valve (Service) - Remove and Install
992K Wheel Loader Electrohydraulic System Ride Control Signal Pressure - Check
IT38H Integrated Toolcarrier and 938H Wheel Loader Axle Oscillation Bearings - Lubricate
Planetary Final Drives for Wheel Loaders, Wheel Tractors, Compactors, Underground Articulated Trucks {4011, 4050, 4051} Planetary Final Drives for Wheel Loaders, Wheel Tractors, Compactors, Underground Articulated Trucks {4011, 4050, 4051}
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0623 - FMI 03
IT38H Integrated Toolcarrier and 938H Wheel Loader Belt - Inspect/Adjust/Replace
IT38H Integrated Toolcarrier and 938H Wheel Loader Transmission Electronic Control System MID 081 - CID 0672 - FMI 08