Final Drive and Wheel - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 155-3597     | 车轮锲块     | 4     |
B     | 4C-5809     | 电动液压泵总成     | 1     |
9U-7536 | 起吊台     | 2     | |
C     | 138-7575     | 连杆支架     | 2     |
D     | -     | 顶出螺钉 5/8 - 11 x 4 in     |
2     |
E     | 138-7574     | 连杆支架     | 1     |
F     | 180-3033     | 千斤顶支座     | 2     |
G     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
138-7575 | 连杆支架     | 1     | |
H     | 140-7742     | 套筒     | 1     |
开始:
- 拆卸传动系防护罩。 请参阅拆解和组装, "变速箱传动系防护罩 - 拆卸和安装"。
- 卸下半轴。 请参阅拆解和组装, "半轴 - 拆卸"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 使用工具 (A) ,塞住前轮。
Show/hide table
图 1 | g01100962 |
- 使用工具 (B) ,将轮胎升离地面。
Show/hide table
图 2 | g01289664 |
- 分离停车制动器。
Show/hide table
图 3 | g01289665 |
- 从松紧调整器 (1) 上卸下销 (4) 。
- 松开螺栓 (3) 。 转动螺栓 (2) ,向下移动松紧张紧器 (1) 。
- 将适当的起吊设备连接在车桥 (5) 上。 半轴 (5) 的重量约为 70 kg (155 lb)。 如图所示,将半轴 (5) 安置在行星齿轮托架 (6) 中。
注: 半轴 (5) 提供平衡作用。
Show/hide table
图 4 | g01285893 |
- 将工具 (C) 和适当的起吊设备安装在行星齿轮托架 (6) 上。 行星齿轮托架 (6) 和半轴 (5) 的重量约为 433 kg (955 lb)。
Show/hide table
图 5 | g01289675 |
Show/hide table
图 6 | g01289676 |
- 拆下螺栓 (7) 。
- 使用工具 (D) ,卸下行星齿轮托架 (6) 和半轴 (5) 。
- 如图所示,将行星齿轮托架 (6) 和半轴 (5) 安置在工具 (F) 上。
Show/hide table
图 7 | g01289681 |
- 使用工具 (E) ,从半轴 (5) 上卸下行星齿轮托架 (6) 。 行星齿轮托架 (6) 的重量约为 363 kg (800 lb)。
- 卸下 O 形密封圈 (8) 。
Show/hide table
图 8 | g01285897 |
- 安装工具 (G) ,在轮毂的拆卸过程中固定车轮到位。
Show/hide table
图 9 | g01289696 |
- 将工具 (C) 、工具 (H) 和适当的起吊设备安装在齿圈和轮毂 (12) 上。 齿圈和轮毂 (12) 的重量约为 172 kg (380 lb)。
Show/hide table
图 10 | g01289699 |
- 卸下螺栓 (9) 、护圈 (10) 和垫片组 (11) (图上未显示)。
- 卸下齿圈和轮毂 (12) 。
Caterpillar Information System:
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller
657G Wheel Scraper Power Train Power Train Guard (Transmission) - Remove and Install
2006/07/31 Bearing Inserts Are Now Used in Frame Steering Bracket {7051, 7073}
Underground Articulated Trucks Truck Payload Measurement System Service Tools
D7G Series 2 and D7G Series II Track-Type Tractors Condenser (Refrigerant) - Clean
D7G Series 2 and D7G Series II Track-Type Tractors Emissions Certification Film
D7G Series 2 and D7G Series II Track-Type Tractors Fuel Tank Cap and Strainer - Clean
Installation Instructions for the 291-1184 Secondary Steering Group (Kit) {4300} Installation Instructions for the 291-1184 Secondary Steering Group (Kit) {4300}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Power Train Guard (Transmission) - Remove and Install
953D Track-Type Loader Machine Systems Cab - Install
953D Track-Type Loader Machine Systems Cab - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Fuel Tank Water and Sediment - Drain
657G Wheel Scraper Power Train Final Drive and Wheel - Install
D11R Starter Solenoid Connections{1467} D11R Starter Solenoid Connections{1467}
Load Haul Dump Machine Machining & Welding Information Consumables
Machining and Welding Information for Underground Articulated Trucks Rear Frame
Machining and Welding Information for Underground Articulated Trucks Front Frame
953D Track-Type Loader Machine Systems Lift Cylinder - Remove and Install
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Remove
953D Track-Type Loader Machine Systems Piston Pump (Implement) - Install
953D Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove
D7G Series 2 and D7G Series II Track-Type Tractors Cutting Edges and End Bits - Inspect/Replace
D7G Series 2 and D7G Series II Track-Type Tractors Battery Disconnect Switch
657G Wheel Tractor-Scraper Machine Systems Steering Control Valve - Remove