Gear Pump (Conveyor System Charge, Vibratory) - Assemble
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. |
- Install O-ring seal (15) onto the pump.
Show/hide table
Illustration 2 g01012708 - Install seal (13) and seal (14) onto plate (12).
Show/hide table
Illustration 3 g01012706 - Install plate (12) onto pump (6).
Show/hide table
Illustration 4 g01012705 - Install gear (10) and gear (11) onto pump (6).
Show/hide table
Illustration 5 g01012704 - Install seal (8) and seal (9) onto plate (7).
Show/hide table
Illustration 6 g01012703 - Install plate (7) onto pump (6).
Show/hide table
Illustration 7 g01012702 - Install housing (4) onto pump (6).
Show/hide table
Illustration 8 g01012701 - Install O-ring seal (5) onto cover (3).
Show/hide table
Illustration 9 g01012699 - Position cover (3) onto housing (4).
- Install bolts (2) into cover (3).
Show/hide table
Illustration 10 g01012697 - Install clip (1) onto the shaft.
Show/hide table
| |
| Illustration 1 | g01012709 |
End By:
- Install the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Conveyor System Charge) - Install".
Caterpillar Information System:
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Disassemble
C11 and C15 Engines for Caterpillar Built Machines System Configuration Parameters
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
TK741, TK751 and TK752 Track Feller Bunchers Engine Supplement Engine Oil Pump - Remove and Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
R2900G Load Haul Dump Steering System Wheel Steering System
735 and 740 Articulated Trucks Torque Converter and Transmission Oil Sample - Obtain
735 and 740 Articulated Trucks Torque Converter and Transmission Oil Level - Check
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Remove
725 and 730 Articulated Trucks Brake Accumulator (Service) - Check
789C Off-Highway Truck/Tractor Water Lines (Coolers)
793D Off-Highway Truck Backup Alarm - Test
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Install
793C Off-Highway Truck Machine Systems Tire and Rim (Front) - Remove
793C Off-Highway Truck Machine Systems Tire and Rim (Front) - Install
793D Off-Highway Truck Belts - Inspect/Adjust/Replace
RM-300 Reclaimer Mixer Power Train Wheel Hub - Non-powered Axle
C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install
583T Pipelayer Power Train Brake Control Valve - Disassemble
2005/01/10 Use Thread Lock Compound on the Bolts of the Fan Drive {1359, 7553}
583T Pipelayer Power Train Brake Control Valve - Assemble
2013/09/02 A New Strainer Assembly For the Hydraulic Tank Is Now Available {5056, 5068}
TK741, TK751 and TK752 Track Feller Bunchers Engine Supplement Engine - Remove
C11 and C15 Engines for Caterpillar Built Machines E096 High Fuel Pressure