Torque Converter and Transmission Oil Level - Check
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照本地法规和指令处置所有液体。 |
在启动发动机前,应检查油位。
- 把机器停放在水平地面上。 接合停泊制动器,降下倾卸车箱。
- 升起发动机罩。 请参阅操作和保养手册, "发动机罩控制器" 。
- 擦净加油盖 (1) 和加油管 (2) 。
注: 油尺与变速箱加油盖是一体的。 变矩器和变速箱油的加油管 (2) 位于机器的左侧靠近空气滤清器。
Show/hide table
图 1 | g01134715 |
- 转动油尺上的手柄,以便卸下油尺。 卸下油尺。
- 用干净的抹布擦净油尺。
- 完全装入油尺。
- 拔出油标尺。
- 检查在油尺的"冷安全启动(COLD SAFE START)" 部位的油位。
如果各处的油在阴影区内,则发动机能启动。 如果油位接近 "冷安全启动(COLD SAFE START)"阴影区的底部,则不要加油。 各处的油位在这一范围内是正常的。
Show/hide table
图 2 | g00788077 |
注: 油尺上标记 "冷安全启动(COLD SAFE START)" 和" 热低怠速(HOT LOW IDLE)"。
- 将油尺插入到加油管中,转动油尺上的手柄,以使加油管和加油盖之间密封。
- 降下发动机罩。
- 启动发动机。 运转机器,直到油温达到正常工作温度。
- 把机器停放在水平地面上。 接合停泊制动器。 使发动机低怠速运转。
- 升起发动机罩。 请参阅操作和保养手册, "发动机罩控制器" 。 转动油尺上的手柄,以便卸下油尺。 油位在油尺上标记"热低怠速(HOT LOW IDLE)"处表明变速箱油位正确。 请参看图2。
- 擦净油尺。
- 完全装入油尺。
- 卸下油尺,检查油位。
- 检查油尺"热低怠速(HOT LOW IDLE)" 部位的油位。 保持油位在油尺的阴影区内。 必要时,通过加油管 (2) 添注油。 参阅操作和保养手册, "润滑剂粘度"。
- 将油尺插入到加油管中,转动油尺上的手柄,以使加油管和加油盖之间密封。
- 关闭发动机,关闭发动机罩。
Caterpillar Information System:
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Remove
725 and 730 Articulated Trucks Brake Accumulator (Service) - Check
789C Off-Highway Truck/Tractor Water Lines (Coolers)
793D Off-Highway Truck Backup Alarm - Test
966H and 972H Wheel Loaders Circuit Breakers - Reset
988H Wheel Loader Machine Systems Demand Fan Valve - Assemble
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Axle Oscillation Bearings - Lubricate
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
988H Wheel Loader Machine Systems Demand Fan Valve - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
735 and 740 Articulated Trucks Torque Converter and Transmission Oil Sample - Obtain
R2900G Load Haul Dump Steering System Wheel Steering System
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
TK741, TK751 and TK752 Track Feller Bunchers Engine Supplement Engine Oil Pump - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
C11 and C15 Engines for Caterpillar Built Machines System Configuration Parameters
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Disassemble
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Assemble
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Gear Pump (Conveyor System Charge, Vibratory) - Install
793C Off-Highway Truck Machine Systems Tire and Rim (Front) - Remove
793C Off-Highway Truck Machine Systems Tire and Rim (Front) - Install
793D Off-Highway Truck Belts - Inspect/Adjust/Replace