Inlet Manifold - Install
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 125-2588     | Allen Wrench     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install new O-ring seals on the six plugs. Install the six plugs in the inlet manifold.
- Install air temperature sensor (3) in inlet manifold (9) .
- Install the wiring harness to the inlet manifold with new wire straps. Attach the wiring harness connector to the engine inlet manifold with tool (A). Tighten the screw to a torque of 9 ± .1 N·m (79 ± 1 lb in).
Note: Do not overtighten the screw.
- Install engine inlet manifold (9) to the cylinder head assembly with a new gasket and 18 bolts (4) .
- Install six wiring harness connectors (2) to the fuel injector pumps.
- Connect tube assembly (6) to inlet manifold (9) .
- Secure the wiring harness to the engine with new straps (8) .
- Install injection actuation pressure sensor (7) to the engine.
- Install the wiring harness connectors to the two speed-timing sensors.
- Connect coolant temperature sensor (1) to the wiring harness. Use new straps and secure the coolant temperature sensor to inlet manifold (9) .
End By:
- Install the air inlet heater solenoid. Refer to Disassembly and Assembly, "Air Inlet Heater Solenoid - Remove and Install".
- Install the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater - Remove and Install".
- Install the rocker arm assemblies and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Caterpillar Information System:
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3054 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Remove
2001/12/01 Recommended Setting Of The Oil Mist Detector Alarm Changed {1336}
3126 Truck Engine Military Inlet Manifold - Remove
Electronic Modular Control Panel II (EMCP II) Engine Setpoint Verification OP9
Electronic Modular Control Panel II (EMCP II) Spare Input/Output Programming OP6
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Upper Bearing - Remove and Install
3408E and 3412E Industrial Engines Diagnostic Flash Code Retrieval
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 02 (for EUI Engines)
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Lower Bearing - Remove and Install
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3056 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3056 Engine
Electronic Modular Control Panel II (EMCP II) SP Fault Code
Electronic Modular Control Panel II (EMCP II) Charging System
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Remove
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler - Remove and Install - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble
3054 and 3056 Marine Generator Set Engines Water Pump - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Assemble
Electronic Modular Control Panel II (EMCP II) Pulse Width Modulated Sensor
3054 and 3056 Industrial and Generator Set Engines Water Pump - Inspect