Engine Oil Filter Base - Remove - 3054 Engine
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 185-3630     | Strap Wrench Assembly     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Use Tool (A) in order to remove engine oil filter (3) from the engine oil filter base (2) .
Show/hide table
Illustration 1 | g00843430 |
- Loosen the hose clamps (4) for the engine oil cooler. Remove the oil cooler lines.
- Remove four bolts (1) that secure the engine oil filter base (2) to the cylinder block.
- Remove the engine oil filter base (2) from the cylinder block. Remove the gasket and plug all openings immediately.
- If equipped, remove the oil supply line for the turbocharger.
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Remove
2001/12/01 Recommended Setting Of The Oil Mist Detector Alarm Changed {1336}
3126 Truck Engine Military Inlet Manifold - Remove
Electronic Modular Control Panel II (EMCP II) Engine Setpoint Verification OP9
Electronic Modular Control Panel II (EMCP II) Spare Input/Output Programming OP6
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Upper Bearing - Remove and Install
3408E and 3412E Industrial Engines Diagnostic Flash Code Retrieval
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 02 (for EUI Engines)
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Lower Bearing - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Travel Brake Valve - Install
3054 and 3056 Industrial and Generator Set Engines Engine Oil Cooler - Inspect
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3054 Engine
3126 Truck Engine Military Inlet Manifold - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3056 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3056 Engine
Electronic Modular Control Panel II (EMCP II) SP Fault Code
Electronic Modular Control Panel II (EMCP II) Charging System
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Remove
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler - Remove and Install - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble
3054 and 3056 Marine Generator Set Engines Water Pump - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Assemble