Engine Oil Cooler - Remove and Install - 3054 Engine
Removal Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Loosen hose clamps (4) for the coolant lines. Remove the coolant lines.
Show/hide table
 | |
| Illustration 1 | g00843575 |
- Remove engine oil cooler adapter bolt (3) from engine oil cooler (2). Remove engine oil cooler (2) from the engine oil filter base (1) .
Installation Procedure
- Clean the mating surfaces of the oil cooler (6) and the oil filter base (3) .
Show/hide table
| | |
| Illustration 2 | g00843575 |
Show/hide table
 | |
| Illustration 3 | g00792970 |
- Position a new rubber O-ring seal on the engine oil cooler (2). Install engine oil cooler (2) onto engine oil filter base (1) .
- Install engine oil cooler adapter bolt (3) on oil filter base (1) and tighten to a torque of 37 N·m (27 lb ft).
- Install coolant hoses onto engine oil cooler (2). Tighten hose clamps (4) .
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Remove
Electronic Modular Control Panel II (EMCP II) Charging System
Electronic Modular Control Panel II (EMCP II) SP Fault Code
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3056 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3056 Engine
3126 Truck Engine Military Inlet Manifold - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Install - 3054 Engine
3054 and 3056 Marine Generator Set Engines Engine Oil Filter Base - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swing Gear and Bearing - Remove
2001/12/01 Recommended Setting Of The Oil Mist Detector Alarm Changed {1336}
3126 Truck Engine Military Inlet Manifold - Remove
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble
3054 and 3056 Marine Generator Set Engines Water Pump - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Assemble
Electronic Modular Control Panel II (EMCP II) Pulse Width Modulated Sensor
3054 and 3056 Industrial and Generator Set Engines Water Pump - Inspect
3054 and 3056 Marine Generator Set Engines Water Pump - Install - 3054 Engine
2014/02/07 The 127-2450 Cylinder Head Kit Includes A New Cylinder Head Group {1100}
Electronic Modular Control Panel II (EMCP II) Indicator for Emergency Stop (for EUI Engines)
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Remove - 3056 Engine
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Install - 3056 Engine
Electronic Modular Control Panel II (EMCP II) Indicator for Emergency Stop (for MUI Engines)