Heat Exchanger - Install - 3056 Engine
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Put the heat exchanger into position and install bolt (8) onto support brackets.
Show/hide table
 | |
| Illustration 1 | g00743960 |
- Install two bolts (9) at the front of the heat exchanger to the support bracket.
Note: If the brackets have been removed, apply Loctite 603 to the bolts that attach the brackets to the cylinder block.
- Install water temperature regulator housing (7) onto the heat exchanger. Slide hose (2) into position and tighten the hose clamps. Slide hose (4) into position and tighten the hose clamps.
Show/hide table
 | |
| Illustration 2 | g00758463 |
- Slide hose (3) into position and tighten the hose clamps.
- Slide hose (1) into position and tighten the hose clamps.
- Install hose (5) and hose (6) onto the heat exchanger. Tighten the hose clamps.
- Install the drain plug for the engine coolant. Install the drain plug for the sea water circuit.
- Fill the cooling system. If the engine uses diesel engine antifreeze/coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses extended life coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Open the valve for the sea water inlet.
- Connect the battery. Run the engine for two minutes and check for leaks. Check the coolant level in the expansion tank.
Caterpillar Information System:
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Remove - 3056 Engine
Electronic Modular Control Panel II (EMCP II) Indicator for Emergency Stop (for EUI Engines)
2014/02/07 The 127-2450 Cylinder Head Kit Includes A New Cylinder Head Group {1100}
3054 and 3056 Marine Generator Set Engines Water Pump - Install - 3054 Engine
3054 and 3056 Industrial and Generator Set Engines Water Pump - Inspect
Electronic Modular Control Panel II (EMCP II) Pulse Width Modulated Sensor
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Assemble
3054 and 3056 Marine Generator Set Engines Water Pump - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler - Remove and Install - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Remove
Electronic Modular Control Panel II (EMCP II) Indicator for Emergency Stop (for MUI Engines)
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Remove - 3054 Engine
2002/06/01 A New Valve Adjusting Screw Is Available {1123}
Electronic Modular Control Panel II (EMCP II) Indicator for High Water Temperature
Electronic Modular Control Panel II (EMCP II) Indicator for Low Oil Pressure
EMCPII+ for Gas Engines Indicator for Overcrank
Electronic Modular Control Panel II (EMCP II) Typical Generator Abbreviations
3054 and 3056 Industrial and Generator Set Engines Automatic Timing Advance Unit - Test
Power Module Switchgear (Low Voltage and Medium Voltage) Alarm Modules
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 02 (for MUI Engines)
Electronic Modular Control Panel II (EMCP II) GSC CID 0110 - FMI 02 (for MUI Engines)
2001/12/10 A New Kit is Available for use on Turbocharged 3054 Engines for C Series and D Series Backhoe Loaders. {1058}