3126B and 3126E On-highway Engines Caterpillar


Engine Oil Pressure Sensor - Remove and Install

Usage:

3126B 1AJ

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01104210

  1. Disconnect harness assembly (1) from engine oil pressure sensor (2).

  2. Remove engine oil pressure sensor (2).

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01104210

  1. Install engine oil pressure sensor (2). Tighten the engine oil pressure sensor to a torque of 10 ± 2 N·m (90 ± 18 lb in).

  2. Connect harness assembly (1) to engine oil pressure sensor (2).

Caterpillar Information System:

3406E and C15 Marine Engines Engine Oil Cooler - Install
C-9 Engines for Caterpillar Built Machines Fuel System
3126B and 3126E On-highway Engines Injection Actuation Pressure Sensor - Remove and Install
3406E Marine Engine Engine Oil Cooler - Remove
3408E and 3412E Engines for Caterpillar Built Machines Poor Acceleration or Response
C11 and C13 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
3126B and 3126E On-highway Engines Coolant Temperature Sensor - Remove and Install
PM3500 Power Modules Voltage Regulators
3406E Marine Engine Water Temperature Regulator - Remove and Install
PM3500 Power Modules Parallel Operation
3126B and 3126E On-highway Engines Fast Idle Enable Circuit - Test
2001/03/01 The Booklet, SENR9620, "Improving Fuel System Durability" Is Available {1250}
3126B and 3126E On-highway Engines Wait To Start Lamp Circuit - Test
PM3516 Power Modules Fuel Transfer System - Prime
C-9 Engines for Caterpillar Built Machines Lubrication System
2001/02/01 Corrections to Operation and Maintenance Manual, SEBU7252-03, "3500B High Displacement Generator Set Engines" {1000, 1900, 7500, 7595, 7595}
2001/02/19 The Booklet, SENR9620, "Improving Fuel System Durability" Is Available {1250}
3406E and C15 Marine Engines Engine Oil Cooler - Disassemble
3500B and 3500B High Displacement Engines for Caterpillar Built Generator Sets Engine Speed/Timing Sensor - Calibrate
3126B and 3126E On-highway Engines Service Brake Pedal Position (Switch 2) Circuit - Test
3500B and 3500B High Displacement Engines for Caterpillar Built Generator Sets Electronic Display Module
3306B-XQ200 Rental Generator Set Engine Enclosure - Inspect
3406E Marine Engine Engine Oil Cooler - Assemble
3126B and 3126E On-highway Engines Boost Pressure Sensor - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.