Water Temperature Regulator - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
- 断开软管组件 (1) 。
Show/hide table
图 1 | g00770364 |
- 从调节器壳 (6) 上断开管组件 (3) 。
Show/hide table
图 2 | g00770365 |
- 拆下螺栓 (4) 。 拆下螺栓 (5) 和板。 拆下弯头 (2) 。
- 拆下螺栓 (8) 和弯头 (7) 。
Show/hide table
图 3 | g00770366 |
- 松开软管卡箍 (10) ,然后断开线束组件 (9) 。
Show/hide table
图 4 | g00770367 |
- 拆下螺栓 (11) 。
Show/hide table
图 5 | g00770368 |
- 拆下调节器壳和衬垫。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将新衬垫和调节器壳放到位。 安装螺栓 (11) 。
Show/hide table
图 6 | g00770368 |
- 连接线束组件 (9) 并拧紧软管卡箍 (10) 。
Show/hide table
图 7 | g00770367 |
- 安装弯头 (7) 和螺栓 (8) 。
Show/hide table
图 8 | g00770366 |
- 安装弯头 (2) 。 安装板和螺栓 (5) 。 安装螺栓 (4) 。
Show/hide table
图 9 | g00770365 |
- 将管组件 (3) 连接到调节器壳 (6) 。
- 连接软管组件 (1) 。
Show/hide table
图 10 | g00770364 |
- 向冷却系统再次加注冷却液。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
Caterpillar Information System:
PM3500 Power Modules Parallel Operation
3126B and 3126E On-highway Engines Fast Idle Enable Circuit - Test
2001/03/01 The Booklet, SENR9620, "Improving Fuel System Durability" Is Available {1250}
3406E and C15 Marine Engines Electronic Control Module - Remove and Install
3406E Marine Engine Fuel Transfer Pump - Install
3406E and C15 Marine Engines Fuel Transfer Pump - Remove
3524B Engines for 797 and 797B Off-Highway Trucks Flywheel - Inspect
795F and 795F Series AC Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Disassemble
3406E and C15 Marine Engines Fuel Filter Base - Remove and Install
3406E Marine Engine Fuel Priming Pump - Remove and Install
3306B-XQ200 Rental Generator Set Engine Before Starting Engine
3406E Engine Turbocharger - Install
PM3500 Power Modules Voltage Regulators
3126B and 3126E On-highway Engines Coolant Temperature Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
3408E and 3412E Engines for Caterpillar Built Machines Poor Acceleration or Response
3406E Marine Engine Engine Oil Cooler - Remove
3126B and 3126E On-highway Engines Injection Actuation Pressure Sensor - Remove and Install
C-9 Engines for Caterpillar Built Machines Fuel System
3406E and C15 Marine Engines Engine Oil Cooler - Install
3126B and 3126E On-highway Engines Engine Oil Pressure Sensor - Remove and Install
3126B and 3126E On-highway Engines Wait To Start Lamp Circuit - Test
PM3516 Power Modules Fuel Transfer System - Prime
C-9 Engines for Caterpillar Built Machines Lubrication System