Fuel Filter Base - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 185-3630     | 带式扳手组件     | 1     |
Show/hide table
失火会造成人身伤害或死亡。 渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 要擦净所有泄漏或喷溅的燃油。 对燃油系统进行工作时不要吸烟。 更换燃油滤清器时,要将断路开关转到“断开”位置或断开蓄电池。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 把供油开关转到"关闭"位置。
- 断开线束组件并拆下燃油压力传感器。 从燃油压力传感器上拆下 O 形密封圈。
- 使用工具 (A) ,从燃油滤清器底座 (3) 上拆下燃油滤清器。
Show/hide table
图 1 | g01026897 |
- 断开软管组件 (2) 。
- 拆下螺栓 (1) 。 拆下燃油滤清器底座 (3) 。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将燃油滤清器底座 (3) 安置在发动机上。 安装螺栓 (1) 。
Show/hide table
图 2 | g01026897 |
- 连接软管组件 (2) 。
- 将燃油滤清器安装到燃油滤清器底座 (3) 上。
- 将 O 形密封圈安装到燃油压力传感器上。 将燃油压力传感器安装到燃油滤清器底座上,并拧紧至扭矩为 10 ± 2 N·m (90 ± 18 lb in)。
- 连接燃油压力传感器的线束组件。
- 将供油开关置于"接通"位置。
- 排出系统中的空气。 请参阅测试与调整, "燃油系统 - 预注"。
Caterpillar Information System:
3406E Marine Engine Fuel Priming Pump - Remove and Install
3306B-XQ200 Rental Generator Set Engine Before Starting Engine
3406E Engine Turbocharger - Install
C-15 and C-16 Industrial Engines Air Compressor - Remove and Install
C-15 and C-16 Industrial Engines Crankshaft - Install
C-15 and C-16 Industrial Engines Engine Oil Pan - Remove and Install
3306B-XQ200 Rental Generator Set Engine Generator Identification
Air Compressor Installation Instructions{1803} Air Compressor Installation Instructions{1803}
SPP101 Skid Mounted Pumper S·O·S Oil Analysis
3516B Generator Set Engines with Dynamic Gas Blending Engine Oil Pressure - Test
C-9 Industrial Engine Engine Description
3406E Engine Flywheel Housing - Remove and Install
795F and 795F Series AC Off-Highway Truck Power Train Final Drive, Brake and Wheel (Rear) - Disassemble
3524B Engines for 797 and 797B Off-Highway Trucks Flywheel - Inspect
3406E and C15 Marine Engines Fuel Transfer Pump - Remove
3406E Marine Engine Fuel Transfer Pump - Install
3406E and C15 Marine Engines Electronic Control Module - Remove and Install
2001/03/01 The Booklet, SENR9620, "Improving Fuel System Durability" Is Available {1250}
3126B and 3126E On-highway Engines Fast Idle Enable Circuit - Test
PM3500 Power Modules Parallel Operation
3406E Marine Engine Water Temperature Regulator - Remove and Install
PM3500 Power Modules Voltage Regulators
3126B and 3126E On-highway Engines Coolant Temperature Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle