Engine Oil Cooler - Disassemble
拆解步骤
开始:
- 拆下发动机机油冷却器。 请参阅拆解和组装, "发动机机油冷却器 - 拆卸"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用 3.17 mm (0.125 in) 直径的直杆清洁发动机机油冷却器的各个管。
- 从机油冷却器旁通体 (3) 上卸下盖子 (1) 。
注: 将识别标记置于发动机机油冷却器和阀帽上，以便在装配过程中正确对齐。
Show/hide table
 | |
| 图 1 | g00770734 |
Show/hide table
 | |
| 图 2 | g00770920 |
Show/hide table
 |
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 从机油冷却器旁通体 (3) 上卸下弹簧 (2) 和旁通阀 (4) 。
- 从机油冷却器旁通体 (3) 上卸下弯头 (5) 和管 (6) 。
Show/hide table
 | |
| 图 3 | g00770809 |
- 从管 (6) 上卸下弯头 (5) 。
Caterpillar Information System:
2001/02/19 The Booklet, SENR9620, "Improving Fuel System Durability" Is Available {1250}
2001/02/01 Corrections to Operation and Maintenance Manual, SEBU7252-03, "3500B High Displacement Generator Set Engines" {1000, 1900, 7500, 7595, 7595}
C-9 Engines for Caterpillar Built Machines Lubrication System
PM3516 Power Modules Fuel Transfer System - Prime
3126B and 3126E On-highway Engines Wait To Start Lamp Circuit - Test
3126B and 3126E On-highway Engines Engine Oil Pressure Sensor - Remove and Install
3406E and C15 Marine Engines Engine Oil Cooler - Install
C-9 Engines for Caterpillar Built Machines Fuel System
3126B and 3126E On-highway Engines Injection Actuation Pressure Sensor - Remove and Install
3406E Marine Engine Engine Oil Cooler - Remove
3408E and 3412E Engines for Caterpillar Built Machines Poor Acceleration or Response
C11 and C13 Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
3500B and 3500B High Displacement Engines for Caterpillar Built Generator Sets Engine Speed/Timing Sensor - Calibrate
3126B and 3126E On-highway Engines Service Brake Pedal Position (Switch 2) Circuit - Test
3500B and 3500B High Displacement Engines for Caterpillar Built Generator Sets Electronic Display Module
3306B-XQ200 Rental Generator Set Engine Enclosure - Inspect
3406E Marine Engine Engine Oil Cooler - Assemble
3126B and 3126E On-highway Engines Boost Pressure Sensor - Remove and Install
C-9 Engines for Caterpillar Built Machines General Information
3126B and 3126E On-highway Engines Engine Oil Temperature Sensor - Remove and Install
315C Excavator Boom and Stick Linkage - Lubricate
3406E Marine Engine Marine Transmission Oil Cooler Core - Remove and Install
3126B and 3126E On-highway Engines Speed/Timing Sensor - Remove and Install
3306B-XQ200 Rental Generator Set Engine Engine Oil Level - Check