There may be several specific symbols on the UPS. The descriptions of the symbols are reviewed in this section. Become familiar with all of the symbols.
Ensure that all of the symbols are legible. Clean the symbols or replace the symbols if the words cannot be read or if the illustrations are not visible. Use a cloth, water, and soap to clean the symbols. Do not use solvents, gasoline, or other harsh chemicals. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the symbols. The symbols that are loosened could drop off the UPS.
Replace any symbol that is damaged or missing. If a symbol was attached to part of the UPS that was replaced, install a new symbol on the replacement part. Your Caterpillar dealer can provide new symbols.
Show/hide table
| Conductor (grounding) for wiring (field) |
Show/hide table
| Point (bonding) for internal bonding of equipment parts to ground |
Show/hide table
| Caution - Refer to the manual for more information. |
Show/hide table
| Risk of electric shock |
Show/hide table
| Input |
Show/hide table
| Output |
Show/hide table
| Alternating Current |
Show/hide table
| Phase |
Show/hide table
| Neutral |
Show/hide table
| Caution - Refer to the Service Manual. |
Show/hide table
| No Service |
Show/hide table
| Read Service Manual |
Show/hide table
| No Connection (Telephone) - This is not a connection for a telecommunication network. |
Show/hide table
| High Leakage Current - A connection to earth ground is essential before connecting the supply. |
Show/hide table
| Lithium Battery - There is danger of explosion if the battery is incorrectly replaced. Replace the battery with the same type of battery or replace the battery with an equivalent battery. Dispose of the batteries according to the manufacture's instructions. |
Show/hide table
| The heat sink or the bracket is not grounded - Test before touching. |
Show/hide table
| Safety - Extra Low Voltage connections only |
Show/hide table
| Wait for five minutes after disconnecting all sources of power before the removal of covers or panels. |
Show/hide table
|
|
|
Illustration 1 | g00873924 |
Connect to the UPS with Specified Cable Only. |
Show/hide table
|
|
|
Illustration 2 | g00873941 |
DC Output |
Show/hide table
|
|
|
Illustration 3 | g00785175 |
This Module Is Part Of The Series 300 System. |
Show/hide table
|
|
|
Illustration 4 | g00785184 |
Bypass Input |
Show/hide table
|
|
|
Illustration 5 | g00785185 |
This System is for use with a Three-Wire Grounded Wye Star Service. |
Show/hide table
|
|
|
Illustration 6 | g00785207 |
This System is for use with a Delta Service. |
Show/hide table
|
|
|
Illustration 7 | g00785208 |
This System is for use with a Impedance Grounded Service. |
Show/hide table
|
|
|
Illustration 8 | g00785210 |
This System is for use with a Four-Wire Grounded Wye Star Service. |
Show/hide table
|
|
|
Illustration 9 | g00785211 |
MMU Modules Are Connected In Parallel. The Input Isolation Switches And Output Isolation Switches Must Be Switched To The Off Position Prior To Servicing The MMU. |
Show/hide table
|
|
|
Illustration 10 | g00785212 |
The UPS Receives Power From Multiple Sources. |
Show/hide table
|
|
|
Illustration 11 | g00785214 |
The MMU Modules Are Connected In Parallel. Voltage May Be Present At The Output Of This Module When The Input Power Has Been Removed. |
Show/hide table
|
|
|
Illustration 12 | g00785215 |
Bypass Switch |
Show/hide table
|
|
|
Illustration 13 | g00785216 |
Input Isolation Switch |
Show/hide table
|
|
|
Illustration 14 | g00785218 |
Output Isolation Switch |
Show/hide table
|
|
|
Illustration 15 | g00785219 |
Disconnect Switch for the MMU |
Show/hide table
|
|
|
Illustration 16 | g00785220 |
Input Switches for the MMU |
Show/hide table
|
|
|
Illustration 17 | g00785221 |
Output Switches for the MMU |
Show/hide table
|
|
|
Illustration 18 | g00785222 |
"ON" Symbol |
Show/hide table
|
|
|
Illustration 19 | g00785223 |
"OFF" Symbol |
Show/hide table
|
|
|
Illustration 20 | g00920799 |
"Do Not Switch" Symbol |