Sprocket - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-6486     | Stand     | 2     |
8S-7611 | Tube     | 2     | |
8S-7615 | Pin     | 2     | |
B     | 132-8223     | Hydraulic Pump and Motor Gp     | 1     |
1U-6221 | Hydraulic Torque Wrench Gp     | 1     | |
132-8154 | Wrench Link     | 1     |
Start By:
- Separate the track assembly. Refer to Disassembly and Assembly, "Track - Separate".
Note: The procedure to remove the right hand final drive sprocket and the procedure to remove the left hand sprocket is identical. The procedure that follows is for one of the sprockets.
- Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Show/hide table
Illustration 1 | g00594968 |
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the sprocket and the track links for the removal of the sprocket from the final drive.
- Use Tooling (B) to remove bolts (1) and the washers that fasten the sprocket to the final drive.
Show/hide table
Illustration 2 | g00595219 |
- Remove cork plugs (2). Use two M24x3.0mm forcing screws to separate the sprocket from the final drive.
Show/hide table
Illustration 3 | g00595234 |
- Attach a suitable lifting device to sprocket (3), as shown. Remove sprocket (3). The weight of sprocket (3) is approximately 75 kg (165 lb).
Show/hide table
Illustration 4 | g00595254 |
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-6486     | Stand     | 2     |
8S-7611 | Tube     | 2     | |
8S-7615 | Pin     | 2     | |
B     | 132-8223     | Hydraulic Pump and Motor Gp     | 1     |
1U-6221 | Hydraulic Torque Wrench Gp     | 1     | |
132-8154 | Wrench Link     | 1     | |
C     | 9S-3263     | Thread Lock Compound     |     |
Note: The procedure to install the right hand sprocket and the procedure to install the left hand sprocket is identical. The procedure that follows is for one of the sprockets.
- Thoroughly clean the mating surfaces of the sprocket and the final drive.
- Attach a suitable lifting device to sprocket (3). The weight of sprocket (3) is approximately 75 kg (165 lb). Position sprocket (3) on the final drive, as shown.
Show/hide table
Illustration 5 | g00595254 |
- Install cork plugs (2) .
Show/hide table
Illustration 6 | g00595234 |
- Apply Tooling (C) to bolts (1). Install bolts (1). Use Tooling (B) to tighten bolts (1) in a crisscross sequence to a torque of 900 ± 100 N·m (660 ± 75 lb ft).
Show/hide table
Illustration 7 | g00595219 |
- Lift the side of the machine in order to remove Tooling (A). Lower the machine to the ground.
Show/hide table
Illustration 8 | g00594968 |
End By: Connect the track assembly. Refer to Disassembly and Assembly, "Track - Connect".
Caterpillar Information System:
325B Excavator Machine Systems Water Valve (Cab Heater) - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Lighting (Chassis) - Remove and Install
3056 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Cab Lighting - Remove and Install
C-9 Engines for Caterpillar Built Machines Unit Injector
M318 and M320 Excavators Machine Electronic Control System Implement Activation
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove
SR500 Generators Bearing (Spherical Roller) - Lubricate
307B Excavator Machine System Specifications Lines (Front) - Common Piping
307B Excavator Hydraulic System Pilot Hydraulic System
345B, 345B Series II and W345B Series II Excavators Machine Systems Final Drive and Travel Motor - Remove
345B, 345B Series II and W345B Series II Excavators Machine Systems Final Drive and Travel Motor - Install
5230 Excavator Service Hour Meter
307B Excavator Electrical And Electronic System General Information
C-9 Engines for Caterpillar Built Machines Front Housing and Covers
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Remove - Series I
SR500 Generators Insulation - Test
307B Excavator Electrical And Electronic System Service Tools
C9 Engine For Caterpillar Built Machines Camshaft Gear - Remove and Install
C9.3 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Install - Series I
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Disassemble - Series I