Final Drive and Travel Motor - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 132-8223     | Power Pack     | 1     |
1U-6221 | Hydraulic Torque Wrench Assembly     | 1     | |
132-8154 | 3/4 inch Square Drive Link     | 1     |
Note: The procedure to install the right hand final drive and the procedure to install the left hand final drive is identical. The procedure that follows is for one of the final drives.
- Attach two lifting straps and a hoist to final drive (1) , as shown. The combined weight of the final drive and the travel motor is 714 kg (1575 lb). It may be necessary to adjust the lifting straps for correct balance of the final drive. Position the final drive and the travel motor on the track roller frame, as shown.
Show/hide table
Illustration 1 | g00595681 |
- Apply 9S-3263 Thread Lock Compound on the threads of bolts (4) . Install the washers and bolts (4) . Use Tooling (A) to tighten bolts (4) to a torque of 800 ± 100 N·m (590 ± 75 lb ft).
Show/hide table
Illustration 2 | g00633042 |
Show/hide table
Illustration 3 | g00594077 |
- Connect hose assembly (2) and hose assembly (3) to the travel motor.
Show/hide table
Illustration 4 | g00633039 |
Show/hide table
NOTICE |
---|
To avoid system damage, make sure that the hydraulic motor is properly filled with hydraulic oil before start-up. |
End By:
- Install the travel brake valve. Refer to Disassembly and Assembly, "Counterbalance Valve (Travel) - Install" in this manual.
- Install the final drive sprocket. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install" in this manual.
Caterpillar Information System:
345B, 345B Series II and W345B Series II Excavators Machine Systems Final Drive and Travel Motor - Remove
345B, 345B Series II and W345B Series II Excavators Machine Systems Sprocket - Remove and Install
325B Excavator Machine Systems Water Valve (Cab Heater) - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Lighting (Chassis) - Remove and Install
3056 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Cab Lighting - Remove and Install
C-9 Engines for Caterpillar Built Machines Unit Injector
M318 and M320 Excavators Machine Electronic Control System Implement Activation
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove
SR500 Generators Bearing (Spherical Roller) - Lubricate
5230 Excavator Service Hour Meter
307B Excavator Electrical And Electronic System General Information
C-9 Engines for Caterpillar Built Machines Front Housing and Covers
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Remove - Series I
SR500 Generators Insulation - Test
307B Excavator Electrical And Electronic System Service Tools
C9 Engine For Caterpillar Built Machines Camshaft Gear - Remove and Install
C9.3 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Install - Series I
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Disassemble - Series I
307B Excavator Electrical And Electronic System Monitor - Disassemble
5130B Excavator Heating and Air Conditioning Control