Crankshaft Rear Seal - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 9U-6205 | Rear Seal Installer | 1 |
1P-0510 | Driver Group | 1 | |
B | FT-2806 | Alignment Tool | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Engines with 14 Bolt Housing Assembly
- Inspect the condition of the gasket. Replace the gasket, if necessary.
- Clean the areas of the parts that will contact each other.
Show/hide table
Illustration 1 g00804647 - Use Tooling (A) and a suitable press to install the crankshaft rear seal into the housing.
- Lubricate the components with clean engine oil. Install Tooling (A) onto the crankshaft flange.
- Position the new gasket on the dowels in the cylinder block.
Show/hide table
Illustration 2 g00606404 Typical example - Place housing (3) and crankshaft rear seal (4) over Tooling (A).
- Position housing (3) on the dowels in the cylinder block.
- Remove Tooling (A).
Show/hide table
Illustration 3 g00632744 The flywheel housing has been removed for photographic purposes only. - Install socket head bolts (2) onto housing (3).
- Install bolts (1) in order to fasten housing (3) to the cylinder block. Tighten all of the bolts to a torque of
22 N·m (16 lb ft) .
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the plastic sleeve after the housing assembly is installed.
- Place Tooling (B) over housing assembly (3). This will center the housing assembly onto the crankshaft flange.
Show/hide table
Illustration 5 g00830867 - Install the bolts with Tooling (B) in position in order to fasten housing assembly (3) to the cylinder block. Tighten bolts 1 and 2 to a torque of
22 N·m (16 lb ft) . - Remove Tooling (B). Tighten the remaining bolts in sequence to a torque of
22 N·m (16 lb ft) .
Show/hide table
Illustration 4 | g00831176 |
Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the crankshaft flange before installation.
End By:
- Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar Information System:
345B, 345B Series II and W345B Series II Excavators Machine Systems Cab Lighting - Remove and Install
C-9 Engines for Caterpillar Built Machines Unit Injector
M318 and M320 Excavators Machine Electronic Control System Implement Activation
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove
SR500 Generators Bearing (Spherical Roller) - Lubricate
307B Excavator Machine System Specifications Lines (Front) - Common Piping
307B Excavator Hydraulic System Pilot Hydraulic System
777D HAA Off-Highway Truck Engine Components - Clean/Inspect, Rebuild/Install Reman, Install New
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
307B Excavator Machine System Specifications Lines (Front) - Single Action (1 Pump)
345B, 345B Series II and W345B Series II Excavators Machine Systems Lighting (Chassis) - Remove and Install
325B Excavator Machine Systems Water Valve (Cab Heater) - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Sprocket - Remove and Install
345B, 345B Series II and W345B Series II Excavators Machine Systems Final Drive and Travel Motor - Remove
345B, 345B Series II and W345B Series II Excavators Machine Systems Final Drive and Travel Motor - Install
5230 Excavator Service Hour Meter
307B Excavator Electrical And Electronic System General Information
C-9 Engines for Caterpillar Built Machines Front Housing and Covers
345B, 345B Series II and W345B Series II Excavators Machine Systems Travel Motor - Remove - Series I
SR500 Generators Insulation - Test
307B Excavator Electrical And Electronic System Service Tools
C9 Engine For Caterpillar Built Machines Camshaft Gear - Remove and Install