Dimensions for Articulated Hitches, Lift Arms, Front Levers and Rear Levers, Oscillating Rear Axle Assemblies, Buckets, and Forks{0677, 0679, 3260, 3269, 6116, 6118, 6119, 6125, 6126, 6127, 7057, 7069, 7100} Caterpillar

Integrated Toolcarrier:

IT12F (S/N: 1KF1-UP; 1SF1-UP; 4NB1-UP; 94Z1-UP)

Integrated Toolcarrier:

IT14B (S/N: 3NJ1-UP)

IT14F (S/N: 4EL1-UP)

IT14G (S/N: 8ZM1-UP; 1WN1-UP)

IT18B (S/N: 4ZD1-UP; 1DF1-UP; 2NJ1-UP)

IT18F (S/N: 6ZF1-UP; 5EJ1-UP; 8GJ1-UP)

IT24F (S/N: 4NN1-UP; 6KN1-UP)

IT28B (S/N: 5SD1-UP; 1HF1-UP; 1JK1-UP)

IT28F (S/N: 1JL1-UP; 3CL1-UP)

IT28G (S/N: 8CR1-UP; 9AR1-UP)

Wheel Loader:

902 (S/N: 7ES1-UP)

906 (S/N: 6ZS1-UP)

908 (S/N: 8BS1-UP)

910F (S/N: 1YK1-UP)

914G (S/N: 7ZM1-UP; 9WM1-UP)

916 (S/N: 2XB1-UP; 9WB1-UP; 5KC1-UP)

918F (S/N: 3TJ1-UP; 2CK1-UP; 5DL1-UP)

920 (S/N: 41J1-UP; 62K1-UP)

924F (S/N: 5NN1-UP; 6MN1-UP; 7PN1-UP)

924G (S/N: AAN1-UP; 9SW1-UP; 3PZ1-UP)

924GZ (S/N: AAB1-UP; 6YW1-UP; 3DZ1-UP)

926E (S/N: 8NB1-UP)

928F (S/N: 8AK1-UP; 2XL1-UP; 7YM1-UP)

928G (S/N: 6XR1-UP; 7SR1-UP)

930 (S/N: 41K1-UP)

930G (S/N: TWR1-UP; TFW1-UP)

Introduction

This Special Instruction outlines the basic procedures to repair worn pin bores or elongated pin bores on the following machines: compact wheel loaders, small wheel loaders and integrated toolcarriers. Repairs include adding metal to the pin bores by applying welds to the bores and machining the bores to the correct dimensions.

This special instruction also lists the dimensions for the following assemblies: articulated hitches, pin bores, lift arms, levers, oscillating rear axle assemblies and bearings for buckets and forks. The assemblies in this publication are used on the following machines: small wheel loaders, compact wheel loaders and integrated toolcarriers.

Use the dimensions in this publication to ensure that the parts are within specifications. The dimensions can also be used in order to repair minor damage.

Note: All of the dimensions are used in order to manufacture the parts. The dimensions are also used to recondition the parts. Repair is encouraged to reduce replacement of the assemblies. However, the extent of the repair should determine the need for replacement.

For Disassembly and Assembly instructions, refer to your machine's Service Manual, Parts Manual, and the Operations and Maintenance Manual. For welding information, refer to the bulletin from the Caterpillar Service Technology Group (CSTG), NEHS0513.

Do not perform any procedure in this publication until you understand the information that is contained in this document.

In the following illustrations, dimensions will be indicated by letters. D stands for diameter. S stands for the spacing between items. T stands for the thickness of an object. W stands for width. L stands for length. R stands for the radius.

Preparing the Pin Bores for Repair

Show/hide table

Personal injury can result from flame cutting or welding on painted areas. The effect of gasses from burned paint is a hazard to the person doing the cutting or welding. Do not flame cut or weld on painted areas.

Remove paint, rust, dirt, and scale with a wire brush or by buffing or grinding. Remove any oil or grease with an approved Caterpillar solvent.

All grease, water, paint, and other foreign material must be removed from the pin bore prior to welding. Any of these materials will discharge gas which will cause porosity in the weld deposit. Water and rust will cause hydrogen embrittlement. Hydrogen embrittlement causes cracks in the weld deposit.

Cover all surfaces, bores, and threads which are not selected for repair. Remove the covers only when the repair work is finished.

Inspection of the Pin Bores

1. Clean the areas around the pin bores.

2. Inspect all the pin bores.

3. If a pin bore is worn or elongated, remove the part from the machine. Refer to your machine's Service Manual for disassembly instructions.

4. Once the part is removed from the machine, clean the pin bores. Refer to the ""Preparing the Pin Bores for Repair" " section of this publication.

5. Inspect the pin bores.

   Pin bores must be inspected prior to any machining or welding. Cracks will occur in the thinner sections around the pin bores. For a quality repair, all cracks must be removed prior to machining.

   To locate cracks in a pin bore, use a dye penetrant or a magnetic particle inspection process. Surfaces should be cleaned and any surface irregularities must be removed before you inspect the parts.

6. Cut out defects to a depth of 6 mm (0.24 inch) beyond the bottom of the defect. Refer to ""Machining Elongated Bores" " in this publication.

Machining Elongated Bores

Metal to metal contact of the pin bore to any frame member can result in material deformation. Machining prior to welding results in a concentric bore. Machining also stabilizes the base material for welding.

A vertical or horizontal mill can be used for machining the bores. Single point tooling is normally used for cutting the bores to specified dimensions. Caterpillar recommends the use of the following carbide cutting tools:

• C5 for a rough cut

• C7 for a smooth surface finish

Set the speed of the spindle between 380 rpm to 600 rpm. The speed of the spindle must not exceed 600 rpm. The feed rate for the spindle is 0.15 to 0.25 mm (0.006 to 0.01 inch).

For doing repairs in the field, Caterpillar recommends the use of 1U-8660 Boring Bar . The hydraulic boring bar is equipped with several attachments. The attachments are needed in order to machine the pin bores to the correct dimensions.

The 1U-8660 Boring Bar can be set up in order to allow machining and welding without adjusting the 1U-8660 Boring Bar .

Applying Welds to a Pin Bore

Once the machining is finished, the metal must be prepared for welding. Follow the instructions below in order to correctly apply welds to the pin bores.

Welding Procedures

Show/hide table

Personal injury or death can result from fumes, gases and ultraviolet rays from the weld arc. Welding can cause fumes, burn skin and produce ultraviolet rays. Keep your head out of the fumes. Use ventilation, exhaust at the arc, or both, to keep fumes and gases from your breathing area. Wear eye, ear and body protection before working. Protect yourself and others; read and understand this warning. Fumes and gases can be dangerous to your health. Ultraviolet rays from the weld arc can injure eyes and burn skin. Electric shock can cause death. Read and understand the manufacturer's instructions and your employer's safety practices. Do not touch live electrical parts. See "American National Standard Z49.1, Safety in Welding and Cutting" published by the American Welding Society. American Welding Society 2501 N.W. 7th Street Miami, Florida 33125 See "OSHA Safety and Health Standards, 29 CFR 1910", available from U.S. Department of Labor. U.S. Department of Labor Washington, D.C. 20210

1. Clean the pin bore. The area around the pin bore must also be cleaned. Refer to ""Preparing the Pin Bores for Repair" " in this publication.

2. Inspect the pin bore. If a defect is found, remove the fault by cutting or machining. Refer to ""Machining Elongated Bores" " for instructions in order to eliminate the fault.

3. Preheat the base metal of the pin bore to a temperature of 95° ± 10°C (203° ± 18°F). Preheating the metal will prevent cracking of the base metal. Preheating will also reduce the chances of hydrogen embrittlement.

4. Use an automated 1U-9600 Welding Group in order to correctly build up a pin bore with welds. Automated welding will result in clean, even metal deposition.

   The 1U-9600 Welding Group offers improved performance over SMAW and GMAW welding systems.

   If the 1U-9600 Welding Group is not available, you can use an E7018 SMAW electrode. The E7018 SMAW electrode has a diameter of 3.18 mm (0.13 inch).

   If an E7018 SMAW electrode cannot be found, you can also use a 1U-5232 Welding Rod or GMAW welding.

   Refer to Table 1 for welding parameters.

   Show/hide table

   Table 1

   Parameters for Welding the Pin Bores
   Welding Wire	Wire Diameter	Feed Speed	Amperage	Volts
   1U-5367	0.89 mm (0.035 inch)	76 to 106 mm/sec (180 to 280 in/min)	75 to 140	18 to 22
   1U-5368	1.14 mm (0.045 inch)	55 to 84 mm/sec (130 to 200 in/min)	150 to 180	18 to 22
   1U-6701	1.14 mm (0.045 inch)	63 to 88 mm/sec (149 to 208 in/min)	160 to 200	17 to 18
   1U-6722	0.89 mm (0.035 inch)	56 to 97 mm/sec (132 to 228 in/min)	100 to 160	15 to 18

   Note: The 1U-9600 Welding Group (60 Hz) is not sold in Europe. The 1U-9601 Welding Group (50 Hz) is sold in Europe only. The 1U-9601 Welding Group (50 Hz) can replace the 1U-9600 Welding Group (60 Hz) .

Show/hide table



Illustration 1	g00612358
Outline the pin bores with welds (A). Apply transverse welds (B) to the bores. The transverse welds should connect the welds which outline the pin bores.

5. Apply a weld (A) to each opening of the pin bore. Refer to Illustration 1.

   Note: Before you begin to weld on the pin bore, preheat the metal to 95 °C (203 °F).

6. Apply multiple welds (B) to the length of the pin bore. The welds must connect the welds which outline the pin bore. Refer to Illustration 1.

   Note: Allow the welds to slowly cool. Repair any welds by removing the existing weld. Apply a weld to the area which is being repaired. Before you begin welding again, you must preheat the pin bore.

7. Machine the welds to the correct dimensions. Dimensions for most pin bores are found in this publication.

Protecting the Welds

New welds must be painted. Paint will protect the welds against rusting. Paint the welds with an authorized Caterpillar paint. The paint will help prevent rust from forming on the new welds. Refer to the following instructions for preparing the welds for painting and for painting the welds.

Finishing the Welds and Painting the Welds

1. Protect all finished bores. Cover the bores in order to prevent paint and other material from entering the bores.

2. Grind all the welds to a smooth finish.

3. Remove any spatter from the surrounding areas around the welds.

4. Shot blast the welds and surrounding areas prior to painting.

5. Paint the welds with a paint that is approved by Caterpillar.

6. Remove all protective outer coverings from the bores.

7. Inspect the grease passages for obstructions before you install new bearings. If the grease passages become blocked, the grease which is used to lubricate the bearings will not reach the bearings. Failure to lubricate the bearings will result in damage to the bearings.

Hitches

902, 906, and 908

Illustration 2	g00590836
The illustration is a graphic representation of the hitch assemblies which are used on the machines. Some differences may exist.

Table 2

The Dimensions for the Hitches
Location	Model
	902/906	908
R1	0.8 ± 0.2 mm (0.032 ± 0.008 inch)
S1	102 ± 1 mm (4.02 ± 0.04 inch)
S2	72 ± 1 mm (2.84 ± 0.04 inch)
S3	48.4 ± 0.04 mm (1.91 ± 0.002 inch)	61.2 ± 1.5 mm (2.41 ± 0.0591 inch)
S4	63 ± 1 mm (2.48 ± 0.04 inch)	89.9 ± 1.0 mm (3.54 ± 0.0394 inch)
S5	198 ± 1 mm (7.80 ± 0.04 inch)	214 ± 2 mm (8.43 ± 0.0787 inch)
S6	62.00 + 0.05 mm, - 0.25 mm (2.44 + 0.002 inch, - 0.01 inch)
S7	66.65 + 0.35 mm, - 0.00 (2.62 + 0.014 inch, - 0.00 inch)
S8	33 ± 1 mm (1.30 ± 0.04 inch)
S9	54 ± 1 mm (2.13 ± 0.04 inch)
D1	69.90 + 0.04 mm, - 0.00 (2.7520 + 0.0016 inch, - 0.00 inch)
D2	38.20 ± 0.04 mm (1.50 ± 0.002 inch)
D3	31.87 ± 0.04 mm (1.25 ± 0.002 inch)	38.22 ± 0.04 mm (1.505 ± 0.0016 inch)
D4	62.25 ± 0.04 mm (2.45 ± 0.002 inch)
D5	50.08 ± 0.04 mm (1.97 ± 0.002 inch)
D6	50.9 ± 0.04 mm (2.00 ± 0.002 inch)	64.99 ± 0.04 mm (2.559 ± 0.002 inch)
D7	90.46 ± 0.02 mm (3.561 ± 0.001 inch)
D8	73.0 ± 0.5 mm (2.87 ± 0.02 inch)
D9	95.27 ± 0.03 mm (3.751 ± 0.001 inch)
D10	61.86 ± 0.10 mm (2.435 ± 0.004 inch)
D11	47.83 ± 0.03 mm (1.883 ± 0.001 inch)
D12	32.00 ± 0.04 mm (1.260 ± 0.002 inch)
D13	57.25 ± 0.04 mm (2.250 ± 0.002 inch)	64.99 ± 0.04 mm (2.559 ± 0.002 inch)
D14	50.80 ± 0.04 mm (2.0000 ± 0.0016 inch)

IT12B, IT18B, IT28B, 910E, and 910F

Illustration 3	g00606413
(AA) Rear frame assembly for the IT12B, 910E, and 910F (BB) Rear frame assembly for the IT18B and the IT28B (CC) Front frame assembly for the IT12B, 910E, and 910F (DD) Front frame assembly for the IT18B and the IT28B

Table 3

The Dimensions for the Hitches
Location	Model
	IT12B	IT18B	IT28B	910E	910F
S1	53.20 ± 0.25 mm (2.10 ± 0.01 inch) (1)	104.0 ± 2.0 mm (4.09 ± 0.08 inch)	104.0 ± 2.0 mm (4.09 ± 0.08 inch)	53.20 ± 0.25 mm (2.10 ± 0.01 inch) (1)	53.20 ± 0.25 mm (2.10 ± 0.01 inch) (1)
S2		52.0 ± 0.5 mm (2.05 ± 0.02 inch)	52.0 ± 0.5 mm (2.05 ± 0.02 inch)
S3/T1	53.20 ± 0.25 mm (2.10 ± 0.01 inch)	74.68 ± 0.25 mm (2.94 ± 0.01 inch)	74.68 ± 0.25 mm (2.94 ± 0.01 inch)	53.20 ± 0.25 mm (2.10 ± 0.01 inch)	53.20 ± 0.25 mm (2.10 ± 0.01 inch)
S4	113.0 ± 0.5 mm (4.45 ± 0.02 inch)	105.0 ± 0.5 mm (4.02 ± 0.02 inch)	114.0 ± 0.5 mm (4.49 ± 0.02 inch)	54.0 ± 0.5 mm (2.13 ± 0.02 inch)	108.0 ± 0.5 mm (4.25 ± 0.02 inch)
S5	80.0 ± 0.5 mm (3.15 ± 0.02 inch)	84.0 ± 0.5 mm (3.31 ± 0.02 inch)	84.0 ± 0.5 mm (3.31 ± 0.02 inch)	105.5 ± 0.5 mm (4.1535 ± 0.0197 inch)	87 ± 1 mm (3.43 ± 0.04 inch)
S6/T6	82.0 ± 0.5 mm (3.23 ± 0.02 inch) (2)	52.0 ± 0.5 mm (2.05 ± 0.02 inch)	52.0 ± 0.5 mm (2.05 ± 0.02 inch)	82.0 ± 0.5 mm (3.23 ± 0.02 inch) (2)	82.0 ± 0.5 mm (3.23 ± 0.02 inch) (2)
S7		50.0 ± 0.5 mm (1.97 ± 0.02 inch)	50.0 ± 0.5 mm (1.97 ± 0.02 inch)
S8	82.0 ± 0.5 mm (3.23 ± 0.02 inch)	125.0 ± 0.5 mm (4.92 ± 0.02 inch)	146.0 ± 0.5 mm (5.75 ± 0.02 inch)	82.0 ± 0.5 mm (3.23 ± 0.02 inch)	82.0 ± 0.5 mm (3.23 ± 0.02 inch)
S9	55.0 ± 0.5 mm (2.17 ± 0.02 inch)	148.0 ± 0.5 mm (5.83 ± 0.02 inch)	147.0 ± 0.5 mm (5.79 ± 0.02 inch)	54.0 ± 0.5 mm (2.13 ± 0.02 inch)	108.0 ± 0.5 mm (4.25 ± 0.02 inch)
S10					90 ± 1 mm (3.54 ± 0.04 inch)
D1	71.400 ± 0.025 mm (2.8110 ± 0.001 inch)	83.000 ± 0.025 mm (3.2677 ± 0.001 inch)	83.000 ± 0.025 mm (3.2677 ± 0.001 inch)	71.400 ± 0.025 mm (2.8110 ± 0.001 inch)	71.400 ± 0.025 mm (2.8110 ± 0.001 inch)
D2		83.000 ± 0.025 mm (3.2677 ± 0.001 inch)	83.000 ± 0.025 mm (3.2677 ± 0.001 inch)
D3	53.34 ± 0.13 mm (2.10 ± 0.005 inch) (3)	38.175 ± 0.040 mm (1.500 ± 0.002 inch)	38.175 ± 0.040 mm (1.500 ± 0.002 inch)	53.34 ± 0.13 mm (2.100 ± 0.005 inch) (3)	53.34 ± 0.13 mm (2.100 ± 0.005 inch) (3)
D4	71.400 ± 0.025 mm (2.810 ± 0.001 inch)	112.74 ± 0.03 mm (4.440 ± 0.001 inch)	122.200 ± 0.025 mm (4.810 ± 0.001 inch)	71.400 ± 0.025 mm (2.810 ± 0.001 inch)	71.400 ± 0.025 mm (2.810 ± 0.001 inch)
D5	63.6 ± 0.5 mm (2.50 ± 0.02 inch)	63.6 ± 0.5 mm (2.50 ± 0.02 inch)	69.9 ± 0.5 mm (2.75 ± 0.02 inch)	38.18 ± 0.04 mm (1.50 ± 0.002 inch)	63.6 ± 0.5 mm (2.50 ± 0.02 inch)
D6	50.9 ± 0.5 mm (2.00 ± 0.02 inch)	50.9 ± 0.5 mm (2.00 ± 0.02 inch)	50.9 ± 0.5 mm (2.00 ± 0.02 inch)	50.9 ± 0.5 mm (2.00 ± 0.02 inch)
D7	44.37 ± 0.05 mm (1.750 ± 0.002 inch)	82.500 ± 0.025 mm (3.250 ± 0.001 inch)	82.500 ± 0.025 mm (3.250 ± 0.001 inch)	44.37 ± 0.05 mm (1.750 ± 0.002 inch)	44.37 ± 0.05 mm (1.750 ± 0.002 inch)
D8	56.50 ± 0.13 mm (2.22 ± 0.005 inch) (3)	38.175 ± .04 mm (1.50 ± 0.002 inch)	38.175 ± .04 mm (1.50 ± 0.002 inch)	56.50 ± 0.13 mm (2.22 ± 0.005 inch) (3)	56.50 ± 0.13 mm (2.22 ± 0.005 inch) (3)
D9	44.37 ± 0.05 mm (1.75 ± 0.002 inch)	57.2 ± 0.05 mm (2.25 ± 0.002 inch)	66.7 ± 0.04 mm (2.63 ± 0.002 inch)	44.37 ± 0.05 mm (1.75 ± 0.002 inch)	44.37 ± 0.05 mm (1.75 ± 0.002 inch)
D10	44.37 ± 0.05 mm (1.750 ± 0.002 inch)	76.20 ± 0.05 mm (3.000 ± 0.002 inch)	85.70 ± 0.04 mm (3.370 ± 0.002 inch)	44.37 ± 0.05 mm (1.750 ± 0.002 inch)	44.37 ± 0.05 mm (1.750 ± 0.002 inch)
D11	50.9 ± 0.5 mm (2.00 ± 0.02 inch)	57.20± 0.05 mm (2.25 ± 0.002 inch)	57.20 ± 0.05 mm (2.25 ± 0.002 inch)	50.90 ± 0.5 mm (2.00 ± 0.02 inch)	50.90 ± 0.5 mm (2.00 ± 0.02 inch)
D12					57.24 ± 0.04 mm (2.25 ± 0.002 inch)

( 1 )	This is the thickness for this model.
( 2 )	This is the space between the parts for this model.
( 3 )	This is a tapered bore.

916 and 926

Illustration 4	g00590820
The illustration is a representation of the hitch assemblies which are used on the machines. Some differences may exist.

Table 4

The Dimensions for the Hitches
Location	Model
	916	926E
S1	104.0 ± 0.5 mm (4.09 ± 0.02 inch)	104.0 ± 0.5 mm (4.09 ± 0.02 inch)
S2	52 ± 0.5 mm (2.05 ± 0.02 inch)	52 ± 0.5 mm (2.05 ± 0.02 inch)
T3	74.6 ± 0.5 mm (2.94 ± 0.02 inch)	87.4 ± 0.5 mm (3.44 ± 0.02 inch)
S4	102.0 ± 0.5 mm (4.02 ± 0.02 inch)	114.0 ± 0.5 mm (4.49 ± 0.02 inch)
S5	98.0 ± 0.5 mm (3.86 ± 0.02 inch)	100.0 ± 0.5 mm (3.94 ± 0.02 inch)
T6	5.0 ± 0.5 mm (2.05 ± 0.02 inch)	52.0 ± 0.5 mm (2.05 ± 0.02 inch)
S7	50.0 ± 0.5 mm (1.97 ± 0.02 inch)	50.0 ± 0.5 mm (1.97 ± 0.02 inch)
S8	125.0 ± 0.5 mm (4.92 ± 0.02 inch)	146.0 ± 0.5 mm (5.75 ± 0.02 inch)
S9	110.0 ± 0.5 mm (4.33 ± 0.02 inch)	147.0 ± 0.5 mm (5.79 ± 0.02 inch)
D1	83.000 ± 0.025 mm (3.2677± 0.001 inch)	83.000 ± 0.025 mm (3.2677± 0.001 inch)
D2	83.000 ± 0.025 mm (3.2677± 0.001 inch)	83.000 ± 0.025 mm (3.2677± 0.001 inch)
D3	38.20 ± 0.04 mm (1.500 ± 0.002 inch)	38.20 ± 0.04 mm (1.500 ± 0.002 inch)
D4	112.70 ± 0.04 mm (4.440 ± 0.002 inch)	122.20 ± 0.025 mm (4.810 ± 0.001 inch)
D5	63.60 ± 0.04 mm (2.500 ± 0.002 inch)	69.90 ± 0.05 mm (2.750 ± 0.002 inch)
D6	57.20 ± 0.04 mm (2.250 ± 0.002 inch)	63.60 ± 0.04 mm (2.500 ± 0.002 inch)
D7	82.50 ± 0.04 mm (3.250 ± 0.002 inch)	82.5 ± 0.04 mm (3.250 ± 0.002 inch)
D8	38.20 ± 0.04 mm (1.500 ± 0.002 inch)	38.20 ± 0.04 mm (1.500 ± 0.002 inch)
D9	57.20 ± 0.04 mm (2.250 ± 0.002 inch)	66.70 ± 0.04 mm (2.630 ± 0.002 inch)
D10	76.20 ± 0.04 mm (3.000 ± 0.002 inch)	85.80 ± 0.04 mm (3.380 ± 0.002 inch)
D11	50.90 ± 0.04 mm (2.000 ± 0.002 inch)	57.20 ± 0.04 mm (2.250 ± 0.002 inch)

924G and 930G

Illustration 5	g01134268
The illustration is a representation of the hitch assembly which is used on the machine. Some differences may exist.

Table 5

The Dimensions for the Assembly for the Non-Engine End Frame
Location	Model
	924G	930G
D1	89.25 ± 0.05 mm (3.514 ± 0.002 inch)
D2	104.70 ± 0.05 mm (4.122 ± 0.002 inch)	89.05 ± 0.05 mm (3.506 ± 0.002 inch)
D3	122.200 ± 0.035 mm (4.811 ± 0.001 inch)
D4	82.500 ± 0.035 mm (3.248 ± 0.001 inch)
D5	63.64 ± 0.04 mm (2.506 ± 0.002 inch)	76.4 ± 0.5 mm (3.01 ± 0.02 inch)
D6	80 ± 1 mm (3.15 ± 0.04 inch)	57.09 ± 0.03 mm (2.248 ± 0.001 inch)
D7	30.0 ± 0.05 mm (1.181 ± 0.002 inch)
T2	87 ± 0.5 mm (3.43 ± 0.02 inch)	92.0 ± 0.5 mm (3.622 ± 0.020 inch)
T3	52.0 ± 0.5 mm (2.05 ± 0.02 inch)
S4	546.5 ± 1.0 mm (21.52 ± 0.04 inch)	672.5 ± 1.0 mm (26.48 ± 0.04 inch)

924GZ

Illustration 6	g01134340
148-7700 Loader Frame Group The illustration is a representation of the hitch assembly which is used on the machine. Some differences may exist.

Table 6

The Dimensions for the Assembly of the Non-Engine End Frame
Location	Model
	924GZ
D1	63.62 ± 0.04 mm (2.505 ± 0.002 inch)
D2	69.97 ± 0.04 mm (2.755 ± 0.002 inch)
D3	63.62 ± 0.04 mm (2.505 ± 0.002 inch)
D4	82.500 ± 0.035 mm (3.248 ± 0.001 inch)
D5	122.200 ± 0.03 mm (4.811 ± 0.001 inch)
D6	30 ± 1 mm (1.18 ± 0.04 inch)
D7	57.09 ± 0.03 mm (2.248 ± 0.001 inch)
D8	80 ± 1 mm (3.15 ± 0.04 inch)
S1	118 ± 3 mm (4.65 ± 0.12 inch)
S2	104 ± 1 mm (4.09 ± 0.04 inch)
S4	546.5 ± 1.0 mm (21.52 ± 0.04 inch)
T1	87 ± 0.5 mm (3.43 ± 0.02 inch)
T2	52 ± 0.5 mm (2.05 ± 0.02 inch)

924G, 924GZ, and 930G

Illustration 7	g01134275
The illustration is a representation of the hitch assembly which is used on the machines. Some differences may exist.

Table 7

The Dimensions for the Assembly of the Engine End Frame
Location	Model
	924G, 924GZ, and 930G
D1	30 ± 1 mm (1.18 ± 0.04 inch)
D2	50.83 ± 0.03 mm (2.001 ± 0.001 inch)
D3	66.715 ± 0.040 mm (2.627 ± 0.002 inch)
D4	85.765 ± 0.040 mm (3.377 ± 0.002 inch)
S1	149 ± 1 mm (5.87 ± 0.04 inch)
S2	108 ± 2 mm (4.25 ± 0.08 inch)

920 and 930

Illustration 8	g00590830
The illustration is a representation of the hitch assemblies which are used on the machines. Some differences may exist.

Table 8

The Dimensions for the Hitches
Location	Model
	920	930
S1	122.63 ± 0.50 mm (4.83 ± 0.02 inch)	126.9 ± 0.5 mm (5.00 ± 0.02 inch)
S2	45.2 ± 0.25 mm (1.78 ± 0.01 inch)	45.2 ± 0.25 mm (1.78 ± 0.01 inch)
T3	74.7 ± 0.5 mm (2.94 ± 0.02 inch)	87.4 ±0.25 mm (3.44 ± 0.01 inch)
S4	65.0 ± 0.5 mm (2.56 ± 0.02 inch)	65.0 ± 0.5 mm (2.56 ± 0.02 inch)
S5	71.6 ± 0.5 mm (2.82 ± 0.02 inch)	71.6 ± 0.5 mm (2.82 ± 0.02 inch)
T6	101.9 ± 2.5 mm (4.01 ± 0.10 inch)	101.9 ± 2.5 mm (4.01 ± 0.10 inch)
S7	50.8 ± 0.5 mm (2.00 ± 0.02 inch)	50.8 ± 0.5 mm (2.00 ± 0.02 inch)
S8	124.5 ± 0.5 mm (4.90 ± 0.02 inch)	146 ± 0.5 mm (5.75 ± 0.02 inch)
S9	142.75 ± 0.5 mm (5.62 ± 0.02 inch)	142.75 ± 0.5 mm (5.62 ± 0.02 inch)
D1	82.60 ± .025 mm (3.25 ± 0.001 inch)	95.30 ± 0.025 mm (3.7520 ± 0.001 inch)
D2	82.600 ± 0.025 mm (3.2520 ± 0.001 inch)	95.300 ± 0.025 mm (3.7520 ± 0.001 inch)
D3	38.100 ± 0.025 mm (1.50 ± 0.001 inch) (3)	38.100 ± 0.025 mm (1.50 ± 0.001 inch) (3)
D4	112.700 ± 0.025 mm (4.4370 ± 0.001 inch)	122.200 ± 0.025 mm (4.8110 ± 0.001 inch)
D5	63.60 ± 0.05 mm (2.50 ± 0.002 inch)	69.95 ± 0.05 mm (2.75± 0.002 inch)
D6	50.9 ± 0.5 mm (2.00 ± 0.02 inch)	50.9 ± 0.5 mm (2.00 ± 0.02 inch)
D7	76.200 ± 0.025 mm (3.00 ± 0.001 inch)	88.400 ± 0.025 mm (3.4803 ± 0.001 inch)
D8	38.10 ± 0.05 mm (1.50 ± 0.002 inch)	38.10 ± 0.05 mm (1.50 ± 0.002 inch)
D9	57.200 ± 0.025 mm (2.2520 ± 0.001 inch)	66.700 ± 0.025 mm (2.6260 ± 0.001 inch)
D10	76.200 ± 0.025 mm (3.00 ± 0.001 inch)	85.750 ± 0.025 mm (3.3760 ± 0.001 inch)
D11	57.20 ± 0.05 mm (2.25 ± 0.002 inch)	63.60 ± 0.05 mm (2.50 ± 0.002 inch)

( 3 )

This is a tapered bore.

IT18F, IT24F, IT28F, 918F, 924F, and 928F

Illustration 9	g01859043
(A) The articulated hitch on the engine end frame (B) The articulated hitch on the front frame assembly for the 918F, 924F, and 928F Wheel Loaders (C) The articulated hitch on the front frame assembly for the IT18F, IT24F, and IT28F Integrated Toolcarriers

Table 9

Dimensions for the Hitches
Location	Model
	IT18F	IT24F	IT28F	918F	924F	928F
S1	95.0 ± 0.5 mm (3.74 ± 0.02 inch)		52.0 ± 0.5 mm (2.05 ± 0.02 inch)	95.0 ± 0.5 mm (3.74 ± 0.02 inch)		52.0 ± 0.5 mm (2.05 ± 0.02 inch)
S2	95.0 ± 0.5 mm (3.74 ± 0.02 inch)		87.0 ± 0.5 mm (3.43 ± 0.02 inch)	95.0 ± 0.5 mm (3.74 ± 0.02 inch)		87.0 ± 0.5 mm (3.43 ± 0.02 inch)
S3	538 ± 1 mm (21.2 ± 0.04 inch)		618.8 ± 1.0 mm (24.4 ± 0.04 inch)	538 ± 1 mm (21.2 ± 0.04 inch)		618.8 ± 1.0 mm (24.4 ± 0.04 inch)
S4		100 ± 1 mm (3.94 ± 0.04 inch)	127 ± 3 mm (5.00 ± 0.12 inch)	107.5 ± 1.0 mm (4.23 ± 0.04 inch)		121 ± 3 mm (4.76 ± 0.12 inch)
S5				104 ± 1 mm (4.09 ± 0.04 inch)		104 ± 1 mm (4.09 ± 0.04 inch)
S6	109 ± 3 mm (4.29 ± 0.12 inch)		112 ± 3 mm (4.41 ± 0.12 inch)	90 ± 3 mm (3.54 ± 0.12 inch)		200 ± 3 mm (7.87 ± 0.12 inch)
S7	57 ± 1 mm (2.24 ± 0.04 inch)
S8	124 ± 1 mm (4.88 ± 0.04 inch)	125 ± 1 mm (4.92 ± 0.04 inch)	151.5 ± 1.0 mm (5.96 ± 0.04 inch)	125 ± 1 mm (4.92 ± 0.04 inch)		147.2 ± 1.5 mm (5.79 ± 0.06 inch)
S9	136 ± 2 mm (5.35 ± 0.08 inch)		106 ± 2 mm (4.17 ± 0.08 inch)	136 ± 2 mm (5.35 ± 0.08 inch)		106 ± 2 mm (4.17 ± 0.08 inch)
D1	100.005 ± 0.018 mm (3.9372 ± 0.0007 inch)		82.500 ± 0.035 mm (3.2480 ± 0.0014 inch)	100.005 ± 0.018 mm (3.9372 ± 0.0007 inch)		82.500 ± 0.035 mm (3.2480 ± 0.0014 inch)
D2	100.005 ± 0.018 mm (3.9372 ± 0.0007 inch)		122.200 ± 0.035 mm (4.8110 ± 0.0014 inch)	100.005 ± 0.018 mm (3.9372 ± 0.0007 inch)		122.200 ± 0.035 mm (4.8110 ± 0.0014 inch)
D3	44.53 ± 0.04 mm (1.753 ± 0.002 inch)
D4	69.94 ± 0.04 mm (2.754 ± 0.002 inch)			63.59 ± 0.04 mm (2.504 ± 0.002 inch)		69.94 ± 0.04 mm (2.754 ± 0.002 inch)
D5	50.89 ± 0.04 mm (2.004 ± 0.002 inch)			57.24 ± 0.04 mm (2.254 ± 0.002 inch)		63.59 ± 0.04 mm (2.504 ± 0.002 inch)
D6	57.24 ± 0.04 mm (2.254 ± 0.002 inch)			50.89 ± 0.04 mm (2.004 ± 0.002 inch)		57.24 ± 0.04 mm (2.254 ± 0.002 inch)
D7	44.53 ± 0.04 mm (1.753 ± 0.002 inch)
D8	76.44 ± 0.04 mm (3.009 ± 0.002 inch)		85.765 ± 0.040 mm (3.37657 ± 0.0016 inch)	76.44 ± 0.04 mm (3.009 ± 0.002 inch)		85.765 ± 0.040 mm (3.37657 ± 0.0016 inch)
D9	57.175 ± 0.040 mm (2.2510 ± 0.0016 inch)		66.715 ± 0.040 mm (2.62657 ± 0.0016 inch)	57.175 ± 0.040 mm (2.2510 ± 0.0016 inch)		66.715 ± 0.040 mm (2.6266 ± 0.0016 inch)
D10	57.175 ± 0.040 mm (2.2510 ± 0.0016 inch)		50.83 ± 0.03 mm (2.001 ± 0.001 inch)	57.175 ± 0.040 mm (2.2510 ± 0.0016 inch)		50.83 ± 0.03 mm (2.001 ± 0.001 inch)
D11	83.000 ± 0.300 mm (3.2677 ± 0.0118 inch)		N/A	83.000 ± 0.300 mm (3.2677 ± 0.0118 inch)		N/A
D12	84.000 ± 0.300 mm (3.3071 ± 0.0118 inch)		N/A	84.000 ± 0.300 mm (3.3071 ± 0.0118 inch)		N/A
D13	95.280 ± 0.030 mm (3.7512 ± 0.0012 inch)		N/A	95.280 ± 0.030 mm (3.7512 ± 0.0012 inch)		N/A
D14	96.800 ± 0.500 mm (3.8110 ± 0.0197 inch)		N/A	96.800 ± 0.500 mm (3.8110 ± 0.0197 inch)		N/A

IT14G, IT28G, 914G, and 928G

Illustration 10	g00590834
(D) The articulated hitch on the engine end frame (E) The hitch assembly on the front frame assembly for the IT14G and IT28G (F) The hitch assembly on the front frame assembly for the 914G and 928G

Table 10

Dimensions for the Hitches
Location	Model
	IT14G	914G	IT28G	928G
S1	127 ± 1 mm (5.00 ± 0.04 inch)		150 ± 2 mm (5.91 ± 0.08 inch)
S2	50 ± 2 mm (1.97 ± 0.08 inch)		48 ± 2 mm (1.89 ± 0.08 inch)
S3	100 ± 2 mm (3.94 ± 0.08 inch)		108 ± 2 mm (4.25 ± 0.08 inch)
S4	108 ± 2 mm (4.25 ± 0.08 inch)	116 ± 2 mm (4.57 ± 0.08 inch)	129 ± 3 mm (5.08 ± 0.12 inch)	132 ± 3 mm (5.20 ± 0.12 inch)
S5		84 ± 2 mm (3.31 ± 0.08 inch)	120 ± 3 mm (4.72 ± 0.12 inch)
S6	91 ± 2 mm (3.58 ± 0.08 inch)		87 ± 2 mm (3.43 ± 0.08 inch)
S7	62 ± 2 mm (2.44 ± 0.08 inch)		52 ± 2 mm (2.05 ± 0.08 inch)
S8		92 ± 2 mm (3.62 ± 0.08 inch)		130 ± 2 mm (5.12 ± 0.08 inch)
D1	26.00 ± 0.04 mm (1.0236 ± 0.0016 inch)		30.00 ± 0.04 mm (1.1811 ± 0.0016 inch)
D2	76.24 ± 0.04 mm (3.0016 ± 0.0016 inch)		85.80 ± 0.04 mm (3.3779 ± 0.0016 inch)
D3	57.20 ± 0.04 mm (2.25 ± 0.002 inch)		66.7 ± 0.04 mm (2.63 ± 0.002 inch)
D4	38.20 ± 0.04 mm (1.50 ± 0.002 inch)		44.50 ± 0.04 mm (1.750 ± 0.002 inch)
D5	50.80 ± 0.04 mm (2.000 ± 0.002 inch)
D6	63.50 ± 0.04 mm (2.50 ± 0.002 inch)		76.30 ± 0.04 mm (3.00 ± 0.002 inch)
D7	57.24 ± 0.04 mm (2.250 ± 0.002 inch)	50.90 ± 0.04 mm (2.000 ± 0.002 inch)	63.60 ± 0.04 mm (2.500 ± 0.002 inch)
D8	50.90 ± 0.04 mm (2.000 ± 0.002 inch)		63.60 ± 0.04 mm (2.500 ± 0.002 inch)
D9	80.932 ± 0.018 mm (3.1863 ± 0.0007 inch)		82.500 ± 0.035 mm (3.2480 ± 0.0014 inch)
D10			30.00 ± 0.04 mm (1.180 ± 0.0012 inch)
D11	100.005 ± 0.018 mm (3.9372 ± 0.0007 inch)		122.200 ± 0.035 mm (4.8110 ± 0.0014 inch)
D12		50.90 ± 0.04 mm (2.000 ± 0.002 inch)		76.00 ± 0.04 mm (2.990 ± 0.002 inch)

Dimensions for Lift Arms

Dimensions for the Lift Arms on the 902, 906, and 908

Illustration 11	g00590854
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 11

Dimensions of the Lift Arms
Location	Model
	902	906	908
L1	2032.6 ± 0.5 mm (80.0 ± 0.012 inch)	2133.2 ± 1.0 mm (83.98 ± 0.04 inch)	2313.4 ± 0.5 mm (91.08 ± 0.02 inch)
L2	1424.4 ± 0.5 mm (56.08 ± 0.02 inch)	1525 ± 0.5 mm (60.04 ± 0.02 inch)	1705.2 ± 0.5 mm (67.13 ± 0.02 inch)
L3	1117.6 ± 0.1 mm (44.00 ± 0.004 inch)	1149.4 ± 0.1 mm (45.3 ± 0.004 inch)	1271.5 ± 0.5 mm (50.06 ± 0.02 inch)
H1	73.3 ± 0.5 mm (2.89 ± 0.02 inch)	75.3 ± 0.5 mm (2.96 ± 0.02 inch)	83.3 ± 0.5 mm (3.28 ± 0.02 inch)
H2	30.0 ± 0.5 mm (1.18 ± 0.02 inch)		40.0 ± 0.5 mm (1.58 ± 0.02 inch)
D1	62.89 ± 0.04 mm (2.476 ± 0.002 inch)
D2	57.25 ± 0.06 mm (2.254 ± 0.002 inch)		64.99 ± 0.06 mm (2.559 ± 0.002 inch)
D3	67.98 ± 0.04 mm (2.676 ± 0.002 inch)
D4
W1	612 ± 1 mm (24.10 ± 0.04 inch)
W2	202.2 ± 0.1 mm (7.96 ± 0.004 inch)		219.2 ± 1.0 mm (8.63 ± 0.04 inch)
W3	314.2 ± 1.0 mm (12.4 ± 0.04 inch)		339.2 ± 1.0 mm (13.35 ± 0.04 inch)
W4	580 ± 1 mm (22.8 ± 0.04 inch)
W5	204.9 ± 0.1 mm (8.07 ± 0.004 inch)		196.4 ± 1.0 mm (7.73 ± 0.04 inch)
W6	88 ± 1 mm (3.46 ± 0.04 inch)

Dimensions for the Lift Arms on the 910

Illustration 12	g00590839
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 12

Dimensions for the Lift Arms on the 910
Model	L1	L2	L3	L4	L5	H1	H2	H3	H4
910	2197 ± 1 mm (86.50 ± 0.04 inch)	1775 ± 1 mm (69.88 ± 0.04 inch)	1328.8 ± 1.0 mm (52.30 ± 0.04 inch)	1173.5 ± 1 mm (46.20 ± 0.04 inch)	309 ± 1 mm (12.20 ± 0.04 inch)	24 ± 5 mm (0.94 ± 0.20 inch)	50.8 ± 5 mm (2.00 ± 0.20 inch)	82.5 ± 5 mm (3.25 ± 0.20 inch)	213 ± 5 mm (8.39 ± 0.20 inch)
	B1	B2	D1	D2	D3	D4	W1	W2
910	50 ± 5 mm (1.97 ± 0.20 inch)	100 ± 5 mm (3.94 ± 0.20 inch)	63.5 ± 5.0 mm (2.50 ± 0.20 inch)	50.8 ± 5.0 mm (2.00 ± 0.20 inch)	63.5 ± 5.0 mm (2.50 ± 0.20 inch)	63.5 ± 5.0 mm (2.50 ± 0.20 inch)	753 ± 5 mm (29.65 ± 0.20 inch)	702.3 ± 5.0 mm (27.65 ± 0.20 inch)

Dimensions for the Lift Arms on the 910E, 910F, and 914G

Illustration 13	g00590840
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 13

Dimensions for Lift Arms
Model	L1	L2	L3	B1	B2	B3
910E 910F	2345 ± 0.5 mm (92.32 ± 0.02 inch)	1535 ± 0.5 mm (60.40 ± 0.02 inch)	1293 ± 0.5 mm (50.90 ± 0.02 inch)	80 ± 5 mm (3.15 ± 0.20 inch)	68 ± 5 mm (2.68 ± 0.20 inch)	100 ± 5 mm (3.94 ± 0.20 inch)
914G	2365 ± 0.5 mm (93.10 ± 0.02 inch)	1546 ± 0.5 mm (60.87 ± 0.02 inch)	1305 ± 0.5 mm (51.38 ± 0.02 inch)	78 ± 5 mm (3.07 ± 0.20 inch)	68 ± 5 mm (2.68 ± 0.20 inch)	98 ± 5 mm (3.86 ± 0.20 inch)
Model	D1	D2	D3	D4	H1	H2
910E 910F	63.40 ± 0.04 mm (2.500 ± 0.002 inch)	76.30 ± 0.04 mm (3.000 ± 0.002 inch)	63.40 ± 0.04 mm (2.500 ± 0.002 inch)	76.10 ± 0.04 mm (2.99 ± 0.002 inch)	500.0 ± 0.5 N·m (368.80 ± 0.37 lb ft)	99.0 ± 0.5 mm (3.90 ± 0.02 inch)
914G					505.0 ± 0.5 mm (19.88 ± 0.02 inch)	100.0 ± 0.5 mm (3.94 ± 0.02 inch)
Model	W1	W2	W3	W4	W5
910E	720.0 ± 3.3 mm (28.35 ± 0.13 inch)	180.0 ± 0.5 mm (7.07 ± 0.02 inch)			700.0 ± 3.3 mm (27.56 ± 0.13 inch)
914G	722.0 ± 3.3 mm (28.43 ± 0.13 inch)				702.0 ± 3.3 mm (27.64 ± 0.13 inch)

Dimensions for the Lift Arms on the 920 and the 930

Illustration 14	g00590841
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 14

Dimensions for the Lift Arms
Model	L1	L2	L3	L4	H2	H3	H4
920	2280.00 ± 0.25 mm (89.760 ± 0.010 inch)	1814.00 ± 0.25 mm (71.420 ± 0.010 inch)	1179.00 ± 0.25 mm (46.420 ± 0.010 inch)	584.20 ± 0.25 mm (23.000 ± 0.010 inch)	53.85 ± 0.25 mm (2.120 ± 0.010 inch)	133.35 ± 0.25 mm (5.250 ± 0.010 inch)	12.70 ± 0.25 mm (0.500 ± 0.010 inch)
930	2451.10 ± 0.25 mm (96.500 ± 0.010 inch)	1889.12 ± 0.25 mm (74.370 ± 0.010 inch)	1155.70 ± 0.25 mm (45.500 ± 0.010 inch)	666.75 ± 0.25 mm (26.250 ± 0.010 inch)	73.15 ± 0.25 mm (2.880 ± 0.010 inch)	139.70 ± 0.25 mm (5.500 ± 0.010 inch)	35.56 ± 0.25 mm (1.400± 0.010 inch)

Table 15

Model	W1	W2	W3	W5	B1	B2	B4	B5
920	899.7 ± 0.8 mm (35.42 ± 0.03 inch)	970.0 ± 0.8 mm (38.19 ± 0.03 inch)	898.65 ± 0.25 mm (35.38 ± 0.01 inch)	616.00 ± 0.25 mm (24.25 ± 0.01 inch)	63.5 ± 0.8 mm (2.50 ± 0.03 inch)			69.85 ± .25 mm (2.75 ± 0.01 inch)
930	942.8 (37.12)	1007.9 (39.68)	911.35 (35.88)	615.95 (24.25)	69.8 ± 0.8 mm (2.75 ± 0.03 inch)

Table 16

Model	D1	D2	D3	D4	D5	S1	S2
920	50.80 ± 0.25 mm (2.00 ± 0.01 inch)		69.90 ± 0.25 mm (2.75 ± 0.01 inch)	50.88 ± 0.25 mm (2.00 ± 0.01 inch)	76.20 ± 0.25 mm (3.00 ± 0.01 inch)	217.0 ± 0.8 mm (8.54 ± 0.03 inch)	212.0 ± 0.8 mm (8.35 ± 0.03 inch)
930	57.05 ± 0.25 mm (2.25 ± 0.01 inch)		76.30 ± 0.25 mm (3.00 ± 0.01 inch)	57.23 ± 0.25 mm (2.25 ± 0.01 inch)	82.45 ± 0.25 mm (3.25 ± 0.01 inch)	282.4 ± 0.8 mm (11.12 ± 0.03 inch)	276.35 ± 0.80 mm (10.880 ± 0.030 inch)

Dimensions for the Lift Arms on the 914G, 916, 918F, 924F, 926, 926E, 928F, and 928G

Illustration 15	g00606582
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 17

Model	L1	L2	L3	H1	H2
914G	2365.00 ± 0.05 mm (93.1 ± 0.002 inch)	1546.00 ± 0.05 mm (60.87 ± 0.002 inch)	1305.00 ± 0.05 mm (51.38 ± 0.002 inch)	505.00 ± 0.05 mm (19.88 ± 0.002 inch)	100.00 ± 0.05 mm (3.94 ± 0.002 inch)
916	2420.00 ± 0.05 mm (95.28 ± 0.002 inch)	1575.00 ± 0.05 mm (62.01 ± 0.002 inch)	1310.00 ± 0.05 mm (51.57 ± 0.002 inch)	510.00 ± 0.05 mm (20.08 ± 0.002 inch)	110.00 ± 0.05 mm (4.33 ± 0.002 inch)
918F
924F
926 926E	2535.00 ± 0.05 mm (99.800 ± 0.002 inch)	1650.00 ± 0.05 mm (64.960 ± 0.002 inch)	1350.00 ± 0.05 mm (53.150 ± 0.002 inch)	560.00 ± 0.05 mm (22.050 ± 0.002 inch)	100.00 ± 0.05 mm (3.940 ± 0.002 inch)
928F
928G	2705.00 ± 0.05 mm (106.500 ± 0.002 inch)	1760.00 ± 0.05 mm (69.290 ± 0.002 inch)	1275.00 ± 0.05 mm (50.200± 0.002 inch)	595.00 ± 0.05 mm (23.430 ± 0.002 inch)	150.00 ± 0.05 mm (5.910 ± 0.002 inch)

Table 18

Model	D1	D2	D3	D4
914G	63.430 ± 0.025 mm (2.4972 ± 0.001 inch)	76.300 ± 0.025 mm (3.0039 ± 0.001 inch)	63.430 ± 0.025 mm (2.4972 ± 0.001 inch)	76.130 ± 0.025 mm (2.9972 ± 0.001 inch)
916
918F
924F
926 926E		89.00 ± 0.025 mm (3.5039 ± 0.001 inch)	69.800 ± 0.025 mm (2.7480 ± 0.001 inch)	82.500 ± 0.025 mm (3.2480 ± 0.001 inch)
928F
928G	76.130 ± 0.025 mm (2.9972 ± 0.001 inch)	101.700 ± 0.025 mm (4.0039 ± 0.001 inch)		88.800 ± 0.025 mm (3.4961 ± 0.001 inch)

Table 19

Model	W1	W2	W4	W5	B1	B2	B3
914G	724.0 ± 0.5 mm (28.50 ± 0.02 inch)	180.0 ± 0.5 mm (7.09 ± 0.02 inch)	732.0 ± 0.5 mm (28.82 ± 0.02 inch)	702.0 ± 0.5 mm (27.64 ± 0.02 inch)	76.0 ± 0.5 mm (2.99 ± 0.02 inch)	68.0 ± 0.5 mm (2.68 ± 0.02 inch)	95.0 ± 0.5 mm (3.74 ± 0.02 inch)
916				700.0 ± 0.5 mm (27.56 ± 0.02 inch)
918F		184.0 ± 0.5 mm (7.24 ± 0.02 inch)			78.2 ± 0.5 mm (3.08 ± 0.02 inch)	67.0 ± 0.5 mm (2.64 ± 0.02 inch)	99.0 ± 0.5 mm (3.90 ± 0.02 inch)
924F
926 926E	750.0 ± 0.5 mm (29.53 ± 0.02 inch)	173.0 ± 0.5 mm (6.81 ± 0.02 inch)	760.0 ± 0.5 mm (29.92 ± 0.02 inch)	728.0 ± 0.5 mm (28.66 ± 0.02 inch)	90.0 ± 0.5 mm (3.54 ± 0.02 inch)	80.0 ± 0.5 mm (3.15 ± 0.02 inch)	112.0 ± 0.5 mm (4.41 ± 0.02 inch)
928F	752.0 ± 0.5 mm (29.61 ± 0.02 inch)	178.0 ± 0.5 mm (7.01 ± 0.02 inch)		729.0 ± 0.5 mm (28.7 ± 0.02 inch)	89.0 ± 0.5 mm (3.50 ± 0.02 inch)	79.0 ± 0.5 mm (3.11 ± 0.02 inch)	111.0 ± 0.5 mm (4.37 ± 0.02 inch)
928G	919.0 ± 0.5 mm (36.18 ± 0.02 inch)	188.0 ± 0.5 mm (7.40 ± 0.02 inch)	929.0 ± 0.5 mm (36.57 ± 0.02 inch)	889.0 ± 0.5 mm (35.00 ± 0.02 inch)	86.0 ± 0.5 mm (3.39 ± 0.02 inch)	75.0 ± 0.5 mm (2.95 ± 0.02 inch)	114.5 ± 0.5 mm (4.51 ± 0.02 inch)

Dimensions for the Lift Arms on the 924G and 924GZ

Illustration 16	g02759738

Table 20

Model	L1	L2	L3	H1
924G 924GZ	2719.4 ± 0.05 mm (107.063 ± 0.002 inch)	2371.8 ± 0.05 mm (93.38 ± 0.002 inch)	450 ± 0.05 mm (17.72 ± 0.002 inch)	50 ± 0.05 mm (1.97 ± 0.002 inch)

Table 21

Model	D1	D2	D3	D4	D5
924G 924GZ	82.50 ± 0.04 mm (3.248 ± 0.001 inch)	76.35 ± 0.05 mm (3.006 ± 0.002 inch)	101.75 ± 0.05 mm (4.006 ± 0.002 inch)	104.70 ± 0.05 mm (4.122 ± 0.002 inch)	63.65 ± 0.04 mm (2.506 ± 0.0015 inch)

Table 22

Model	W1	W2	W3	B1	B2	B3
924G 924GZ	216.0 ± 0.05 mm (8.52 ± 0.002 inch)		210 ± 0.05 mm (8.27 ± 0.002 inch)	131.5 ± 0.05 mm (5.18 ± 0.002 inch)	203 ± 0.05 mm (7.99 ± 0.002 inch)

Dimensions for the Lift Arms on the 930G

Illustration 17	g01137413
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 23

Model	L1	L2	L3	H1	H2	H2
930G235-7302	2690.5 ± 0.5 mm (105.93 ± 0.02 inch)	2342.6 ± 0.5 mm (92.23 ± 0.02 inch)	455.5 ± 0.5 mm (17.93 ± 0.02 inch)	175.0 ± 0.5 mm (6.89 ± 0.02 inch)	136.8 ± 0.5 mm (5.39 ± 0.02 inch)	84.4 ± 0.5 mm (3.32 ± 0.02 inch)
930G235-7362	3004.3 ± 0.5 mm (118.28 ± 0.02 inch)	2696.8 ± 0.5 mm (106.17 ± 0.02 inch)		578.3 ± 0.5 mm (22.78 ± 0.02 inch)	486.7 ± 0.5 mm (19.16 ± 0.02 inch)

Table 24

Model	D1	D2	D3	D4	D5
930G	82.50 ± 0.04 mm (3.248 ± 0.001 inch)	76.35 ± 0.05 mm (3.006 ± 0.002 inch)	101.75 ± 0.05 mm (4.006 ± 0.002 inch)	104.70 ± 0.05 mm (4.122 ± 0.002 inch)	76.35 ± 0.05 mm (3.006 ± 0.002 inch)

Table 25

Model	W1	W2	W3	B1	B2	B3
930G	216.0 ± 0.5 mm (8.52 ± 0.02 inch)			131.5 ± 0.5 mm (5.18 ± 0.02 inch)	190.0 ± 0.5 mm (7.48 ± 0.02 inch)

Dimensions for the Lift Arms on the IT12, IT12B, IT12F, IT14B, IT14F, IT14G, IT18F, IT18B, IT18F, IT24F, IT28, IT28B, IT28F, and IT28G

Illustration 18	g00590844
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 26

Model	L1	L2	L3	L4	D1	D2	D3	D4	D5
IT12 IT12B IT12F	2450.00 ± 0.25 mm (96.46 ± 0.01 inch)	2070.00 ± 0.25 mm (81.5 ± 0.01 inch)	1400.00 ±0.25 mm (55.120 ± 0.010 inch)	453.00 ± 0.25 mm (17.83 ± 0.01 inch)	63.50 ± 0.05 mm (2.50 ± 0.002 inch)	50.70 ± 0.05 mm (2.00 ± 0.002 inch)	63.50 ± 0.05 mm (2.50 ± 0.002 inch)		76.20 ± 0.05 mm (3.00 ± 0.002 inch)
IT14B IT14F
IT14G		2038 ± 0.25 mm (80.24 ± 0.01 inch)	1485 ± 0.25 mm (58.46 ± 0.01 inch)		63.40 ± 0.05 mm (2.50 ± 0.002 inch)		63.4 ± .05 mm (2.50 ± 0.002 inch)
IT18	2535.00 ± 0.25 mm (99.8 ± 0.01 inch)	2085.00 ± 0.25 mm (82.09 ± 0.01 inch)	1350.00 ± 0.25 mm (53.15 ± 0.01 inch)	450 ± .25 mm (17.72 ± 0.01 inch)	63.4 ± 0.05 mm (2.500 ± 0.002 inch)			82.50 ± 0.05 mm (3.250 ± 0.002 inch)	76.13 ± 0.05 mm (2.997 ± 0.002 inch)
IT18B					63.43 ± 0.04 mm (2.5 ± 0.002 inch)		69.78 ± 0.05 mm (2.75 ± 0.002 inch)
IT18F								82.5 ± .05 mm (3.25 ± 0.002 inch)
IT24F
IT28	2570.00 ± 0.25 mm (101.2 ± 0.01 inch)	2120.00 ± 0.25 mm (83.500 ± 0.010 inch)	1400.00 ± 0.25 mm (55.12 ± 0.01 inch)
IT28B
IT28F
IT28G	2680.00 ± 0.25 mm (105.5 ± 0.01 inch)	2230.00 ± 0.25 mm (87.80 ± 0.01 inch)			76.13 ± 0.25 mm (2.997 ± 0.010 inch)	63.40 ±0.05 mm (2.500 ± 0.002 inch)	76.13 ± 0.25 mm (2.997 ± 0.010 inch)	88.80 ± 0.05 mm (3.500 ± 0.002 inch)

Table 27

Model	H1	H2	H3	B1	B2	B3	B4	B5
IT12 IT12B IT12F	30.0 ± 0.25 mm (1.18 ± 0.01 inch)	140.00 ± 0.25 mm (5.51 ± 0.01 inch)	15.00 ± 0.25 mm (0.59 ± 0.01 inch)	853 ± 2 mm (33.6 ± 0.08 inch)			877 ± 1.6 mm (34.53 ± 0.06 inch)	907 ± 1 mm (35.71 ± 0.04 inch)
IT14B IT14F
IT14G	20.00 ± 0.25 mm (0.79 ± 0.01 inch)	120 ± .25 mm (4.72 ± 0.01 inch)		885 ± 2 mm (34.84 ± 0.08 inch)			909.0 ± 1.6 mm (35.79 ± 0.06 inch)	939 ± 1 mm (36.97 ± 0.04 inch)
IT18		150.00 ± 0.25 mm (5.91 ± 0.01 inch)	50.00 ± 0.25 mm (1.97 ± 0.01 inch)	920 ± 2 mm (36.22 ± 0.08 inch)	900.0 ± 1.6 mm (35.43 ± 0.06 inch)	888.0 ± 1.6 mm (34.96 ± 0.06 inch)	916.0 ± 1.6 mm (36.06 ± 0.06 inch)	920 ± 2 mm (36.22 ± 0.08 inch)
IT18B
IT18F				1086.6 ± 2.0 mm (42.78 ± 0.08 inch)	1068.0 ± 1.6 mm (42.05 ± 0.06 inch)		1083.0 ± 1.6 mm (42.64 ± 0.06 inch)	1097.6 ± 1.0 mm (43.21 ± 0.04 inch)
IT24F
IT28				920 ± 2 mm (36.22 ± 0.08 inch)			936.0 ± 1.6 mm (36.85 ± 0.06 inch)	952 ± 1 mm (37.48 ± 0.04 inch)
IT28B
IT28F				1079.4 ± 2.0 mm (42.50 ± 0.08 inch)	964.0 ± 1.6 mm (37.95 ± 0.06 inch)		1079 ± 2 mm (42.50 ± 0.08 inch)	1086 ± 1 mm (42.76 ± 0.04 inch)
IT28G				1106 ± 2 mm (43.54 ± 0.08 inch)	1134.1 ± 1.6 mm (44.65 ± 0.06 inch)		1144 ± 2 mm (45.04 ± 0.08 inch)	1149 ± 1 mm (45.24 ± 0.04 inch)

Table 28

Model	W1	W2	W3	W4	W5	M1		M2
IT12	751.0 ± 5.2 mm (29.6 ± 0.2 inch)	751.0 ± 1.6 mm (29.7 ± 0.06 inch)		737.0 ± 1.6 mm (29.02 ± 0.06 inch)	697.0 ± 1.6 mm (27.44 ± 0.06 inch)
IT14B IT14F				727.0 ± 1.6 mm (28.6 ± 0.06 inch)
IT14G	783.0 ± 5.2 mm (30.8 ± 0.2 inch)	783.0 ± 1.6 mm (30.83 ± 0.06 inch)		759.0 ± 1.6 mm (29.88 ± 0.06 inch)	729.0 ± 1.6 mm (28.7 ± 0.06 inch)	8.0 ± 2.6 mm (0.3 ± 0.1 inch)		35.0 ± 1.6 mm (1.38 ± 0.06 inch)
IT18	720.0 ± 5.2 mm (28.35 ± 0.2 inch)	740.0 ± 1.6 mm (29.13 ± 0.06 inch)	752.0 ± 1.6 mm (29.61 ± 0.06 inch)	724.0 ± 1.6 mm (28.50 ± 0.06 inch)	720.0 ± 1.6 mm (28.35 ± 0.06 inch)	30.0 ± 2.6 mm (1.18 ± 0.1 inch)		30.0 ± 1.6 mm (1.18 ± 0.06 inch)
IT18B
IT18F	884.6 ± 5.2 mm (34.83 ± 0.20 inch)	904 ± 1.6 mm (35.59 ± 0.06 inch)		889 ± 1.6 mm (35.00 ± 0.06 inch)	873.6 ± 1.6 mm (34.39 ± 0.06 inch)
IT24F
IT28	720.0 ± 5.2 mm (28.35 ± 0.2 inch)	760.0 ± 1.6 mm (29.9 ± 0.06 inch)		744.0 ± 1.6 mm (29.29 ± 0.06 inch)	728.0 ± 1.6 mm (28.66 ± 0.06 inch)	35.0 (1.38)		31.0 (1.22)
IT28B
IT28F	884.6 ± 5.2 mm (34.83 ± 0.2 inch)	900.0 ± 1.6 mm (35.43 ± 0.06 inch)		885.0 ± 1.6 mm (34.84 ± 0.06 inch)	873.6 ± 1.6 mm (34.39 ± 0.06 inch)
IT28G	904.0 ± 5.2 mm (35.59 ± 0.20 inch)	922.0 ± 1.6 mm (36.3 ± 0.06 inch)		902.0 ± 1.6 mm (35.5 ± 0.06 inch)	893.0 ± 1.6 mm (35.16 ± 0.06 inch)	30.5 ± 2.6 mm (1.20 ± 0.1 inch)		35.5 ± 1.6 mm (1.40 ± 0.06 inch)

Dimensions for Front Levers

Dimensions for the Front Levers on the 902, 906, and 908

Illustration 19	g00690916

Table 29

Dimensions for the Front Levers
Location	Model
	902	906	908
L1	700.0 ± 0.5 mm (27.56 ± 0.02 inch)
L2	508.0 ± 0.5 mm (20.0 ± 0.02 inch)
D1	55.20 ± 0.05 mm (2.1732 ± 0.0020 inch)
D2	50.90 ± 0.05 mm (2.004 ± 0.002 inch)		64.99 ± .05 mm (2.559 ± 0.002 inch)
D3	61.94 ± 0.80 mm (2.439 ± 0.032 inch)
W1	318 ± 1 mm (12.52 ± 0.04 inch)		343 ± 1 mm (13.51 ± 0.04 inch)
W2	25.0 ± 0.5 mm (0.98 ± 0.02 inch)		30.0 ± 0.5 mm (1.18 ± 0.02 inch)
W3	62 ± 1.5 mm (2.44 ± 0.06 inch)		124.5 ± 0.5 mm (4.90 ± 0.02 inch)

Dimensions for the Front Levers on the 910

Illustration 20	g00590855
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 30

Model	L1	L2	G1	G2	D1	D2	D3	W5
910 5G-2421	738.00 ± 0.13 mm (29.06 ± 0.005 inch)	260.50 ± 0.13 mm (10.2559 ± 0.0051 inch)	5.0 ± 1.5 mm (0.20 ± 0.06 inch)		38.23 ± 0.08 mm (1.51 ± 0.003 inch)			10.0 ± 1.5 mm (0.40 ± 0.06 inch)
910 6S-3396	745.7 ± 0.13 mm (29.36 ± 0.005 inch)	268.22 ± 0.13 mm (10.56 ± 0.005 inch)

Dimensions for the Front Levers on the 910E, 910F, and 914G

Illustration 21	g00590857
The illustration is a graphic representation of the lift arms which are used on the machines. Some differences may exist.

Table 31

Model	W1	W2	W3	L1	L2	D1	D2	D3
910E (S/N: 1SF; 1-286) 5G-8586 910E (S/N: 1SF; 287-Up) 4E-3250 910F	80 ± 2 mm (3.15 ± 0.08 inch)	177.5 ± 1.5 mm (6.99 ± 0.06 inch)	120.0 ± 0.5 mm (4.72 ± 0.02 inch)	1180.0 ± 0.5 mm (46.46 ± 0.02 inch)	670.0 ± 0.5 mm (26.38 ± 0.02 inch)	57.24 ± 0.04 mm (2.25 ± 0.002 inch)	88.82 ± 0.05 mm (3.50 ± 0.002 inch)	57.24 ± 0.04 mm (2.25 ± 0.002 inch)
914G				1190.0 ± 0.5 mm (46.85 ± 0.02 inch)	675.0 ± 0.5 mm (26.57 ± 0.02 inch)	120 ± 0.04 mm (4.72 ± 0.002 inch)		120 ± 0.04 mm (4.72 ± 0.002 inch)

Dimensions for the Front Levers on the 920 and the 930

Illustration 22	g00590858
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 32

Model	Part Number	L1	L2	D1	D2	D3
920	7K-1275 7K-1276	558.80 ± 0.25 mm (22.00 ± 0.01 inch)	255.60 ± 0.25 mm (10.06 ± 0.01 inch)	38.20 ± 0.05 mm (1.500 ± 0.002 inch)	44.55 ± 0.05 mm (1.750 ± 0.002 inch)	38.20 ± 0.05 mm (1.50 ± 0.002 inch)
930	7K-3755 7K-3756	638.20 ± 0.25 mm (25.13 ± 0.01 inch)	295.30 ± 0.25 mm (11.63 ± 0.01 inch)	44.55 ± .05 mm (1.750 ± 0.002 inch)
Model	Part Number	W1	W2	W3	W4	W5	W6
920	7K-1275 7K-1276	139.7 ± 0.5 mm (5.50 ± 0.02 inch)	65.30 ± 0.25 mm (2.57 ± 0.02 inch)	21.60 ± 0.05 mm (0.85 ± 0.02 inch)	52.6 ± 0.05 mm (2.07 ± 0.02 inch)	2.8 ± 0.5 mm (0.11 ± 0.02 inch)	46.5 ± 0.5 mm (1.83 ± 0.02 inch)
930	7K-3755 7K-3756	162.1 ± 0.5 mm (6.38 ± 0.02 inch)	71.6 ± 0.5 mm (2.82 ± 0.02 inch)	16.8 ± 0.5 mm (0.66 ± 0.02 inch)			52.6 ± 0.05 mm (2.07 ± 0.02 inch)

Dimensions for the Front Levers on the 916, 918F, 924F, 926, 924G, 924GZ, 926E, 928F, 928G, and 930G

Illustration 23	g00590861
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 33

Model	Part Number	W1	W2	W3	W4	W5
916	5V-1877	79.0 ± 0.5 mm (3.11 ± 0.02 inch)	49.5 ± 0.5 mm (1.95 ± 0.02 inch)	178 ± 0.5 mm (7.01 ± 0.02 inch)	79 ± .5 mm (3.11 ± 0.02 inch)	115 ± 0.5 mm (4.53 ± 0.02 inch)
918F
924F
926 926E	7V-3519		45.5 ± 0.5 mm (1.79 ± 0.02 inch)	170 ± 0.5 mm (6.69 ± 0.02 inch)		120 ± 0.5 mm (4.72 ± 0.02 inch)
928F
928G	113-3734	86.0 ± 0.5 mm (3.39 ± 0.02 inch)	48.50 ± 0.5 mm (1.91 ± 0.02 inch)	183.0 ± 0.5 mm (7.20 ± 0.02 inch)	86.0 ± 0.5 mm (3.39 ± 0.02 inch)	125.0 ± 0.5 mm (4.92 ± 0.02 inch)
924G 924GZ 930G	148-7791	80 ± 2 mm (3.1496 ± 0.08 inch)		185.5 ± 0.5 mm (7.3031 ± 0.02 inch)	80 ± 2 mm (3.15 ± 0.08 inch)	120.0 ± 0.5 mm (4.72 ± 0.02 inch)
	235-7351	110 ± 2 mm (4.33 ± 0.08 inch)		210 ± 2 mm (8.27 ± 0.08 inch)	110 ± 2 mm (4.33 ± 0.08 inch)
930G	235-7359			180 ± 2 mm (7.09 ± 0.08 inch)		57.1 ± 0.5 mm (2.25 ± 0.02 inch)

Table 34

Model	Part Number	L1	L2	D1	D2	D3
916	5V-1877	1130 ± 1 mm (44.49 ± 0.04 inch)	480 ± 1 mm (18.90 ± 0.04 inch)	57.24 ± 0.05 mm (2.25 ± 0.002 inch)	88.82 ± 0.05 mm (3.50 ± 0.002 inch)	57.24 ± 0.05 mm (2.25 ± 0.002 inch)
918F
924F
926 926E	7V-3519	1185 ± 1 mm (46.65 ± 0.04 inch)	500 ± 1 mm (19.69 ± 0.04 inch)	63.60 ± 0.05 mm (2.50 ± 0.002 inch)	104.70 ± 0.05 mm (4.12 ± 0.002 inch)	63.60 ± 0.05 mm (2.500 ± 0.002 inch)
928G
928F
924G 924GZ 930G	148-7791	1185.0 ± 0.5 mm (46.65 ± 0.02 inch)	500.0 ± 0.5 mm (19.69 ± 0.02 inch)	63.68 ± 0.05 mm (2.51 ± 0.002 inch)	104.70 ± 0.05 mm (4.122 ± 0.002 inch)	63.68 ± 0.05 mm (2.507 ± 0.002 inch)
	235-7351	665.0 ± 0.5 mm (26.18 ± 0.02 inch)	225.0 ± 0.5 mm (8.86 ± 0.02 inch)	88.82 ± 0.05 mm (3.50 ± 0.002 inch)	76.35 ± 0.05 mm (3.006 ± 0.002 inch)
930G	235-7359	1092.5 ± 0.5 mm (43.01 ± 0.02 inch)

Dimensions for the Front Levers on the IT12, IT12B, IT12F, IT14B, IT14F, IT14G, IT18, IT18B, IT18F, IT24F, IT28, IT28F and IT28G

Illustration 24	g00590864
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 35

Model	Part Number	W1	W2	W3	W4
IT12	5G-4972	49 ± 1 mm (1.93 ± 0.04 inch)			100 ± 5 mm (3.94 ± 0.2 inch)
IT12B IT12F	9C-7764	53 ± 1 mm (2.09 ± 0.04 inch)		49 ± 1 mm (1.93 ± 0.04 inch)
IT14B IT14F
IT14G	110-9229	49 ± 1 mm (1.93 ± 0.04 inch)			108 ± 5 mm (4.25 ± 0.2 inch)
IT18 IT18B IT18F	6W-0524	100 ± 1 mm (3.94 ± 0.04 inch)	80 ± 1 mm (3.15 ± 0.04 inch)	68 ± 1 mm (2.68 ± 0.04 inch)
IT24F
IT28	9V-4971
IT28F	9C-8859		82 ± 1 mm (3.23 ± 0.04 inch)
IT28G	142-0552	66 ± 1 mm (2.60 ± 0.04 inch)	80 ± 1 mm (3.15 ± 0.04 inch)	100 ± 1 mm (3.94 ± 0.04 inch)

Table 36

Model	Part Number	L1	L2	D1	D2	D3
IT12	5G-4972	732 ± 5 mm (28.82 ± 0.20 inch)	282 ± 5 mm (11.1 ± 0.2 inch)	50.770 ± 0.025 mm (2.00 ± 0.001 inch)
IT12B IT12F	9C-7764			63.480 ± 0.025 mm (2.500 ± 0.001 inch)	50.770 ± 0.025 mm (2.00 ± 0.001 inch)
IT14B IT14F
IT14G	110-9229	793.0 (31.22)	305.0 (12.01)
IT18 IT18B IT18F	6W-0524	765.0 (30.1)	225.0 (8.8)	63.430 ± 0.025 mm (2.500 ± 0.001 inch)
IT24F
IT28 IT28B	9V-4971
IT28F	9C-8859
IT28G	142-0552	880 ± 5 mm (34.65 ± 0.20 inch)	515 ± 5 mm (20.30 ± 0.20 inch)	63.430 ± 0.025 mm (2.500 ± 0.001 inch)		76.130 ± 0.025 mm (2.997 ± 0.001 inch)

Dimensions for the Rear Levers

Dimensions for the Rear Levers on the 920, 930, 924G, and 930G

Illustration 25	g00590869
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 37

Model	Part Number	W1	W2	W3	W4	W5	W6
920	3K-2115 3K-2116	52.3 ± 0.5 mm (2.06 ± 0.02 inch)	70.6 ± 0.5 mm (2.78 ± 0.02 inch)	19.8 ± 0.5 mm (0.78 ± 0.02 inch)	52.3 ± 0.5 mm (2.06 ± 0.02 inch)	107.9 ± 0.5 mm (4.25 ± 0.02 inch)	143.5 ± 0.5 mm (5.65 ± 0.02 inch)
	7K-9607 7K-9608	52.6 ± 0.5 mm (2.07 ± 0.02 inch)	70.4 ± 0.5 mm (2.77 ± 0.02 inch)	26.2 ± 0.5 mm (1.03 ± 0.02 inch)	52.6 ± 0.5 mm (2.07 ± 0.02 inch)
924G	143-4969	170 ± 2 mm (6.70 ± 0.08 inch)			170 ± 2 mm (6.70 ± 0.08 inch)		235 ± 2 mm (9.25 ± 0.08 inch)
930G	235-7341	135.5 ± 1.5 mm (5.34 ± 0.06 inch)			111 ± 2 mm (4.4 ± 0.1 inch)	49.1 ± 0.5 mm (1.93 ± 0.02 inch)	157 ± 2 mm (6.18 ± 0.08 inch)
930	8V-9003 6K-6157 8V-8997 6K-6158	65.3 ± 0.5 mm (2.57 ± 0.02 inch)	57.7 ± 0.5 mm (2.27 ± 0.02 inch)	18.8 ± 0.5 mm (0.74 ± 0.02 inch)	52.6 ± 0.5 mm (2.07 ± 0.02 inch)	76.2 ± 0.5 mm (3.00 ± 0.02 inch)	114.3 ± 0.5 mm (4.50 ± 0.02 inch)
Model	Part Number	L1	L2	D1	D2	D3
920	3K-2115 3K-2116 7K-9607 7K-9608	760.60 ± 0.25 mm (29.94 ± 0.01 inch)	431.8 ± 0.25 mm (17.0 ± 0.01 inch)	50.9 ± 0.05 mm (2.00 ± 0.002 inch)	82.55 ± 0.03 mm (3.25 ± 0.0012 inch)	44.55 ± 0.05 mm (1.750 ± 0.002 inch)
930	8V-9003 6K-6157 8V-8997 6K-6158	854.2 ± 0.5 mm (33.63 ± 0.02 inch)	498.6 ± 0.5 mm (19.63 ± 0.02 inch)		88.89 ± 0.5 mm (3.50 ± 0.02 inch)
924G	143-4969	926.0 ± 0.5 mm (36.46 ± 0.02 inch)	516.0 ± 0.5 mm (20.31 ± 0.02 inch)	89.05 ± 0.05 mm (3.506 ± 0.002 inch)	117.40 ± 0.05 mm (4.622 ± 0.002 inch)	89.05 ± 0.05 mm (3.506 ± 0.002 inch)
930G	235-7341	1037.7 ± 0.5 mm (40.85 ± 0.02 inch)	517.7 ± 0.5 mm (20.38 ± 0.02 inch)

Dimensions for the Rear Levers on the IT12, IT14G, IT18, IT28 and IT28G

Illustration 26	g00590866
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist. The lever which is drawn at the top of the illustration is used on IT12 and IT14G. The lever which is drawn at the bottom of the illustration is used on IT18, IT28, and IT28G.

Table 38

Model	Part Number	W1	W2	W3	W4
IT12	5G-4981 5G-4976	42 ± 1 mm (1.65 ± 0.04 inch)		55 ± 1 mm (2.17 ± 0.04 inch)	25 ± 5 mm (0.98 ± 0.20 inch)
IT14G	111-4025 110-9231	45 ± 1 mm (1.77 ± 0.04 inch)	32 ± 1 mm (1.26 ± 0.04 inch)		28 ± 5 mm (1.10 ± 0.20 inch)
IT18	9V-5081 9V-5083	35 ± 1 mm (1.38 ± 0.04 inch)	40 ± 1 mm (1.57 ± 0.04 inch)	48.5 ± 1.0 mm (1.91 ± 0.04 inch)	60 ± 5 mm (2.36 ± 0.20 inch)
IT28	9V-5081 9V-5083
IT28G	122-6368 122-6369	46 ± 1 mm (1.81 ± 0.04 inch)	45 ± 1 mm (1.77 ± 0.04 inch)	30 ± 1 mm (1.18 ± 0.04 inch)
Model	Part Number	L1	L2	D1	D2	D3
		±5.0 (±.20)	±5.0 (±.20)	±1.0 (±.04)	±1.0 (±.04)	±1.0 (±.04)
IT12	5G-4981 5G-4976	635 ± 5 mm (25.0 ± 0.2 inch)	220 ± 5 mm (8.66 ± 0.20 inch)	50.95 ± 1.00 mm (2.01 ± 0.04 inch)		38.2 ± 1 mm (1.50 ± 0.04 inch)
IT14G	111-4025 110-9231	668.6 ± 5.0 mm (26.30 ± 0.20 inch)		38.2 ± 1.0 mm (1.50 ± 0.04 inch)	50.95 ± 1.00 mm (2.010 ± 0.040 inch)
IT18	9V-5081 9V-5083	750 ± 5 mm (29.53 ± 0.20 inch)	250 ± 5 mm (9.84 ± 0.2 inch)	50.89 ± 1.00 mm (2.00 ± 0.04 inch)	69.94 ± 1.00 mm (2.75 ± 0.04 inch)	50.89 ± 1.00 mm (2.00 ± 0.04 inch)
IT28	9V-5081 9V-5083
IT28G	122-6368 122-6369				76.3 ± 1.0 mm (3.00 ± 0.04 inch)	63.59 ± 1.0 mm (2.50 ± 0.04 inch)

Dimensions for Oscillating Rear Axle Components and Supports

Dimensions for the 910

Illustration 27	g00590872
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 39

Dimensions for the Rear Axle Assembly
Item	Part Number	Description	Diameter	Width
1	6S-4378	Front Support	127.00 ± 0.05 mm (5.000 ± 0.002 inch)
2	6S-3939	Bearing Support Housing	115.00 ± 0.08 mm (4.530 ± 0.003 inch)
3			119.00 ± 0.025 mm (4.690 ± 0.001 inch)
4	6S-3024	Differential Carrier	119.180 ± 0.025 mm (4.690 ± 0.001 inch)
5			342.9 ± 0.08 mm (13.500 ± 0.003 inch)
6	6S-4060	Axle Housing	343.13 ± 0.08 mm (13.510 ± 0.003 inch)
7			115.32 ± 0.13 mm (4.540 ± 0.005 inch)
8			93.00 ± 0.25 mm (3.660 ± 0.010 inch)
9	6S-4072	Rear Trunnion	115.00 ± 0.08 mm (4.530 ± 0.003 inch)
10			95.25 ± 0.25 mm (3.750 ± 0.010 inch)
11	6S-4426	Rear Support	127.00 ± 0.05 mm (5.000 ± 0.002 inch)
12	6S-3939	Bearing Support Housing	113.80 ± 0.13 mm (4.480 ± 0.005 inch)	4.62 ± 0.10 mm (0.180 ± 0.004 inch)

Dimensions for the Rear Axles on the 910E, 910F, IT12B, IT12F, IT14B, and IT14F

Illustration 28	g00590875
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 40

Dimensions for the Rear Axle Assembly
Item	Part Number	Description	Diameter	Width
1	9C-8003	Front Support Assembly	137.00 ± 0.05 mm (5.390 ± 0.002 inch)
2	9C-4804	Pinion Housing	125.00 ± 0.08 mm (4.920 ± 0.003 inch)
3			132.00 ± 0.04 mm (5.200 ± 0.002 inch)
4	4E-2492	Housing Assembly	132.11 ± 0.04 mm (5.200 ± 0.002 inch)
5			346.50 ± 0.04 mm (13.600 ± 0.002 inch)
6	8R-4090	Axle Housing	301.85 ± 0.04 mm (11.800 ± 0.001 inch)
7			136.500 ± 0.035 mm (5.3700 ± 0.0010 inch)
8			120.000 ± 0.035 mm (4.7200 ± 0.0010 inch)
9	4E-3159	Rear Trunnion	88.80 ± 0.08 mm (3.500 ± 0.003 inch)
10	9C-8009	Rear Support	101.60 ± 0.05 mm (4.000 ± 0.002 inch)
11	9C-8003	Front Support	137.10 ± 0.13 mm (5.40 ± 0.005 inch)	9.27 ± 0.13 mm (0.37 ± 0.005 inch)
12	9C-4804	Pinion Housing	125.90 ± 0.13 mm (4.960 ± 0.005 inch)	4.95 ± 0.10 mm (0.190 ± 0.004 inch)

Dimensions for the Rear Axle Assemblies on the 914G and IT14G

Illustration 29	g00590878
The illustration is a graphic representation of the levers which are used on the machines. Some differences may exist.

Table 41

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	140-0453	Front Support	200.80 ± 0.25 mm (7.910± 0.010 inch)
2	109-0616	Pinion Housing	197.60 ± 0.08 mm (7.780 ± 0.003 inch)
3			132.00 ± 0.04 mm (5.198 ± 0.002 inch)
4	117-3299	Housing	132.11 ± 0.04 mm (5.200 ± 0.002 inch)
5			347.00 ± 0.04 mm (13.700 ± 0.002 inch)
6	117-3292, 117-3293	Axle Housing	259.00 ± 0.04 mm (10.200 ± 0.002 inch)
7			114.90 ± 0.35 mm (4.520 ± 0.010 inch)
8			100.000 ± 0.035 mm (3.940 ± 0.001 inch)
9	4E-3159	Rear Trunnion	88.80 ± 0.08 mm (3.500 ± 0.003 inch)
10	109-3720	Frame Assembly	101.60 ± 0.04 mm (4.000 ± 0.002 inch)
11	140-0453	Front Support	209.60 ± 0.13 mm (8.250 ± 0.005 inch)	9.27 ± 0.13 mm (0.360 ± 0.005 inch)
12	109-0616	Pinion Housing	125.90 ± 0.13 mm (4.960 ± 0.005 inch)	4.95 ± 0.10 mm (0.195 ± 0.004 inch)

Dimensions for the Rear Axle Assemblies on the 916 and IT18B

Illustration 30	g00590880
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 42

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	9V-7754	Front Support	165.20 ± 0.05 mm (6.500 ± 0.002 inch)
2	9V-7747	Bearing Support Housing	152.44 ± 0.08 mm (6.000 ± 0.003 inch)
3			165.00 ± 0.04 mm (6.498 ± 0.002 inch)
4	9V-7608	Differential Carrier	165.11 ± 0.04 mm (6.500 ± 0.002 inch)
5			358.74 ± 0.08 mm (14.120 ± 0.003 inch)
6	8V-9341	Axle Housing	358.93 ± 0.15 mm (14.130 ± 0.006 inch)
7			206.40 ± 0.15 mm (8.130 ± 0.006 inch)
8	9V-1260	Rear Trunnion	206.18 ± 0.1 mm (8.120 ± 0.004 inch)
9			88.80 ± 0.08 mm (3.497 ± 0.003 inch)
10	5V-0473	Rear Support	101.60 ± 0.05 mm (4.000 ± 0.002 inch)
11	9V-7754	Front Support	169.47 ± 0.20 mm (6.670 ± 0.008 inch)	2.48 ± 0.07 mm (0.098 ± 0.003 inch)
12	9V-7747	Bearing Support Housing	159.70 ± 0.13 mm (6.290 ± 0.005 inch)	4.95 ± 0.10 mm (0.190 ± 0.004 inch)
13	5V-0473	Rear Support	99.59 ± 0.13 mm (3.920 ± 0.005 inch)	6.74 ± 0.15 mm (0.270 ± 0.006 inch)

Dimensions for the Rear Axle Assemblies on the 918F and the IT18F

Illustration 31	g00590882
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 43

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	8R-8470	Front Support	165.20 ± 0.05 mm (6.500 ± 0.002 inch)
2	8R-2525	Housing	152.44 ± 0.08 mm (6.000 ± 0.003 inch)
3			165.00 ± 0.04 mm (6.496 ± 0.002 inch)
4	8R-3087	Housing Assembly	165.11 ± 0.04 mm (6.50 ± 0.002 inch)
5			348.00 ± 0.13 mm (13.700 ± 0.005 inch)
6	116-4585	Axle Housing	321.90 ± 0.04 mm (12.670 ± 0.002 inch)
7			125.370 ± 0.035 mm (4.940 ± 0.001 inch)
8			100.00 ± 0.04 mm (3.940 ± 0.002 inch)
9	108-4152	Rear Trunnion	88.80 ± 0.08 mm (3.496 ± 0.003 inch)
10	8R-8469	Rear Support	101.60 ± 0.05 mm (4.00 ± 0.002 inch)
11	8R-8470	Front Support	169.5 ± 0.2 mm (6.67 ± 0.01 inch)	2.46 ± 0.07 mm (0.097 ± 0.003 inch)
12	8R-2525	Housing	159.70 ± 0.13 mm (6.290 ± 0.005 inch)	4.95 ± 0.10 mm (0.195 ± 0.004 inch)
13	8R-8469	Rear Support	100.32 ± 0.13 mm (3.950 ± 0.005 inch)	9.27 ± 013 mm (0.365 ± 0.005 inch)

Dimensions for the Rear Axle Assemblies on the 920

Illustration 32	g00590886
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 44

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	6K-9293	Front Support	165.10± 0.05 mm (6.500± 0.002 inch)
2	9K-2545	Bearing Support Housing	162.32 ± 0.08 mm (6.390 ± 0.003 inch)
3			165.01 ± 0.04 mm (6.496 ± 0.002 inch)
4	6K-5611	Differential Carrier	165.11 ± 0.04 mm (6.500± 0.002 inch)
5			361.91 ± 0.08 mm (14.230 ± 0.003 inch)
6	4V-4709	Axle Housing	362.15 ± 0.15 mm (14.260 ± 0.006 inch)
7			209.70 ± 0.15 mm (8.260 ± 0.006 inch)
8	6K-9073	Rear Trunnion	209.45 ± 0.08 mm (8.25 ± 0.003 inch)
9			88.80 ± 0.08 mm (3.500 ± 0.003 inch)
10	6K-9294	Rear Support	101.60 ± 0.05 mm (4.000 ± 0.002 inch)
11	6K-9293	Front Support	169.47 ± 0.20 mm (6.670 ± 0.008 inch)	2.44 ± 0.08 mm (0.096 ± 0.003 inch)
12	9K-2545	Bearing Support	159.74 ± 0.13 mm (6.29 ± 0.005 inch)	4.62 ± 0.10 mm (0.18 ± 0.004 inch)
13	6K-9294	Rear Support	99.60 ± 0.13 mm (3.920 ± 0.005 inch)	8.71 ± 0.13 mm (0.340± 0.005 inch)

Dimensions for the Rear Axle Assemblies on the 924F and the IT24F

Illustration 33	g00590888
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 45

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	117-5110	Front Support	165.20 ± 0.05 mm (6.500 ± 0.002 inch)
2	8R-2525	Housing	152.44 ± 0.08 mm (6.00 ± 0.003 inch)
3			165.00 ± 0.04 mm (6.496 ± 0.002 inch)
4	8R-3087	Housing Assembly	165.11 ± 0.04 mm (6.500 ± 0.002 inch)
5			348.00 ± 0.13 mm (13.700 ± 0.005 inch)
6	116-4585	Axle Housing	321.90 ± 0.04 mm (12.670 ± 0.002 inch)
7			125.370 ± 0.035 mm (4.9400 ± 0.0010 inch)
8	108-4152	Trunnion	165.00 ± 0.04 mm (6.500 ± 0.002 inch)
9			88.80 ± 0.08 mm (3.500 ± 0.003 inch)
10	8R-8469	Rear Support	101.60 ± 0.05 mm (4.000 ± 0.002 inch)
11	117-5110	Front Support	169.5 ± 0.2 mm (6.67 ± 0.01 inch)	2.46 ± 0.07 mm (0.097 ± 0.003 inch)
12	8R-2525	Housing	159.70 ± 0.13 mm (6.290 ± 0.005 inch)	4.95 ± 0.10 mm (0.190 ± 0.004 inch)
13	8R-8469	Rear Support	100.32 ± 0.13 mm (3.950 ± 0.005 inch)	9.27 ± 0.13 mm (0.360 ± 0.005 inch)

Dimensions for the Rear Axle Assemblies on the 924G and the 924GZ

Illustration 34	g00590888
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 46

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	128-0219	Front Support	173.46 ± 0.05 mm (6.829 ± 0.002 inch)
2	140-6140	Housing	157.57 ± 0.08 mm (6.204 ± 0.003 inch)
3			165.00 ± 0.04 mm (6.496 ± 0.002 inch)
4	203-2775	Housing Assembly	165.11 ± 0.04 mm (6.50 ± 0.002 inch)
5			318.0 ± 0.5 mm (12.52 ± 0.02 inch)
6	203-2777	Axle Housing	326.87 ± 0.04 mm (12.869 ± 0.002 inch)
7			146.925 ± 0.035 mm (5.7844 ± 0.0014 inch)
8	8R-2584	Trunnion	150.0 ± 0.01 mm (5.906 ± 0.0004 inch)
9			101.45 ± 0.08 mm (3.994 ± 0.0031 inch)
10	141-4892	Rear Support	114.30 ± 0.05 mm (4.500 ± 0.002 inch)
11	128-0219	Front Support	182.42 ± 0.20 mm (7.182 ± 0.008 inch)	2.46 ± .07 mm (0.097 ± 0.003 inch)
12	140-6140	Housing	159.7 ± 0.13 mm (6.290 ± 0.005 inch)	4.95 ± .1 mm (0.190 ± 0.004 inch)
13	141-4892	Rear Support	112.22 ± 0.13 mm (4.418 ± 0.005 inch)	9.27 ± 0.13 mm (0.360 ± 0.005 inch)

Dimensions for the Rear Axle Assemblies on the 926E and the IT28B

Illustration 35	g00590894
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 47

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	6K-6078	Front Support	180.98 ± 0.05 mm (7.130 ± 0.002 inch)
2	6K-9963	Bearing Support Housing	165.07 ± 0.08 mm (6.500 ± 0.003 inch)
3			165.01 ± 0.04 mm (6.500 ± 0.002 inch)
4	9V-1259	Differential Carrier	165.11 ± 0.04 mm (6.500 ± 0.002 inch)
5			358.70 ± 0.08 mm (14.120 ± 0.003 inch)
6	8V-4850	Axle Housing	358.93 ± 0.08 mm (14.130 ± 0.003 inch)
7			206.40 ± 0.15 mm (8.130 ± 0.006 inch)
8	9V-1258	Rear Trunnion	206.18 ± 0.10 mm (8.120 ± 0.004 inch)
9			101.45 ± 0.08 mm (3.990 ± 0.003 inch)
10	6K-6077	Rear Support	114.30 ± 0.05 mm (4.500 ± 0.002 inch)
11	6K-6078	Front Support	185.95 ± 0.05 mm (7.320 ± 0.002 inch)	2.41 ± 0.08 mm (0.095 ± 0.003 inch)
12	6K-9963	Bearing Support Housing	159.74 ± 0.13 mm (6.290 ± 0.005 inch)	4.62 ± 0.10 mm (0.180 ± 0.004 inch)
13	6K-6077	Rear Support	115.65 ± 0.13 mm (4.550 ± 0.005 inch)	11.76 ± 0.15 mm (0.460 ± 0.006 inch)

Dimensions for the Rear Axle Assemblies on the 928F, 928G, IT28F, and IT28G

Illustration 36	g00590898
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 48

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	126-7502	Front Support	173.46 ± 0.05 mm (6.830 ± 0.002 inch)
2	8R-2189	Housing	157.57 ± 0.08 mm (6.200 ± 0.003 inch)
3			149.90 ± 0.04 mm (5.901± 0.002 inch)
4	8R-1498	Housing Assemblies	150.00 ± 0.04 mm (5.910 ± 0.002 inch)
5			366.0 ± 0.1 mm (14.410 ± 0.004 inch)
6	115-5823	Axle Housing	349.88 ± 0.04 mm (13.770 ± 0.002 inch)
7			136.470 ± 0.035 mm (5.370 ± 0.001 inch)
8	8R-2584	Rear Trunnion	150.0 ± 0.1 mm (5.910 ± 0.004 inch)
9			101.45 ± 0.08 mm (3.990 ± 0.003 inch)
10	125-4973	Rear Support	114.30 ± 0.05 mm (4.500 ± 0.002 inch)
11	126-7502	Front Support	182.42 ± 0.20 mm (7.180 ± 0.008 inch)	2.46 ± 0.07 mm (0.097 ± 0.003 inch)
12	8R-2189	Housing	144.60 ± 0.13 mm (5.690 ± 0.005 inch)	4.95 ± 0.10 mm (0.195 ± 0.004 inch)
13	125-4973	Rear Support	112.21 ± 0.13 mm (4.420 ± 0.005 inch)	9.27 ± 0.13 mm (0.365 ± 0.005 inch)

Dimensions for the Rear Axle Assemblies on the 930G

Illustration 37	g00590888
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 49

Dimensions for the Rear Axle Assemblies
Item	Part Number	Description	Diameter	Width
1	128-0219	Front Support	173.46 ± 0.05 mm (6.829 ± 0.002 inch)
2	8R-2189	Housing	157.57 ± 0.08 mm (6.204 ± 0.003 inch)
3			149.90 ± 0.04 mm (5.9016 ± 0.0016 inch)
4	205-3210	Housing Assembly	149.90 ± 0.04 mm (5.902 ± 0.002 inch)
5			346.0 ± 0.5 mm (13.62 ± 0.02 inch)
6	234-4244	Axle Housing	354.88 ± 0.04 mm (13.972 ± 0.002 inch)
7			146.925 ± 0.035 mm (5.7844 ± 0.0014 inch)
8	8R-2584	Trunnion	150.0 ± 0.01 mm (5.906 ± 0.0004 inch)
9			101.45 ± 0.08 mm (3.994 ± 0.0031 inch)
10	141-4892	Rear Support	114.30 ± 0.05 mm (4.500 ± 0.002 inch)
11	128-0219	Front Support	182.42 ± 0.20 mm (7.182 ± 0.008 inch)	2.46 ± .07 mm (0.097 ± 0.003 inch)
12	8R-2189	Housing	142.0 ± 0.04 mm (5.591 ± 0.002 inch)	4.95 ± .1 mm (0.190 ± 0.004 inch)
13	141-4892	Rear Support	112.22 ± 0.13 mm (4.418 ± 0.005 inch)	9.27 ± 0.13 mm (0.360 ± 0.005 inch)

Dimensions for the Rear Axle Assembly on the 930

Illustration 38	g00590900
The illustration is a graphic representation of the axles which are used on the machines. Some differences may exist.

Table 50

Dimensions for the Rear Axle Assembly
Item	Part Number	Description	Diameter	Width
1	6K-6078	Front Support	180.98 ± 0.05 mm (7.130 ± 0.002 inch)
2	6K-9963	Bearing Support Housing	165.07 ± 0.08 mm (6.500 ± 0.003 inch)
3			165.01 ± 0.04 mm (6.500 ± 0.002 inch)
4	6K-9974	Differential Carrier	165.11 ± 0.04 mm (6.500 ± 0.002 inch)
5			361.90 ± 0.08 mm (14.250 ± 0.003 inch)
6	4V-4711	Axle Housing	362.10 ± 0.15 mm (14.260 ± 0.006 inch)
7			209.70 ± 0.15 mm (8.260 ± 0.006 inch)
8	7K-7430	Rear Trunnion	209.45 ± 0.08 mm (8.250 ± 0.003 inch)
9			101.45 ± 0.08 mm (3.990 ± 0.003 inch)
10	6K-6077	Rear Support	114.30 ± 0.05 mm (4.500 ± 0.002 inch)
11	6K-6078	Front Support	185.95 ± 0.05 mm (7.320 ± 0.002 inch)	2.46 ± 0.07 mm (0.097 ± 0.003 inch)
12	6K-9963	Bearing Support Housing	159.74 ± 0.13 mm (6.290 ± 0.005 inch)	4.62 ± 0.1 mm (0.180 ± 0.004 inch)
13	6K-6077	Rear Support	115.65 ± 0.13 mm (4.55 ± 0.005 inch)	11.76 ± 0.15 mm (0.46 ± 0.006 inch)

Dimensions for the Buckets and Forks

Illustration 39	g00760229
The illustration is a representation of the hook on buckets which are used on the machines. This is adaptable to the other buckets and forks which are used on the machines. Dimensions for the Buckets and Forks are listed in Table 51.

Table 51

The Dimensions for the Buckets and Forks
Item	Dimension
S1	463 mm (18.2 inch)
S2	205 mm (8.1 inch)
Inner Radius of Hook (R1)	31.5 mm (1.24 inch)
Inner Diameter of Bearing After Assembly (D1)	50.89 ± 0.06 mm (2.004 ± 0.002 inch)
Inner Diameter of Bearing Bore (D2)	73.60 ± 0.04 mm (2.898 ± 0.002 inch)
Length of Bearing (L1)	40.00 ± 0.25 mm (1.575 ± 0.010 inch)
Fillet Weld (T1)	5 mm (0.2 inch)