Installation of 4P1976 Base Group (3406) and/or 4P1980 Base Group (3306) for Marine Auxiliary Generator Sets{7060} Caterpillar


Installation of 4P1976 Base Group (3406) and/or 4P1980 Base Group (3306) for Marine Auxiliary Generator Sets{7060}

Usage:

3306 (1DG, 5JC, 1RD, 85Z);
3406 (2WB, 3SF)

Introduction

Use the information in this instruction for installation of the marine auxiliary generator set base groups given above. These base groups require only a minimum amount of space and are, therefore, ideal for use on board ship.


NOTICE

These base groups must not be used with spring type isolators.


Reference: Service Manual, Parts Book.

Installation

Use shims or grout to make sure the foundation (floor or other type mounting surface) has a smooth flat surface for installation of the generator set base.

The area where the generator set base is to be installed must be flat to within a maximum deviation of no more than 6.35 mm (0.25").

Refer to the general dimension drawings for installation dimensions.

Caterpillar Information System:

Using The ECAP NEXG4516 Marine/Industrial Engine Functions Service Program Module{0701, 0782} Using The ECAP NEXG4516 Marine/Industrial Engine Functions Service Program Module{0701, 0782}
Installation of 7E5253 Governor Control Assembly{1265} Installation of 7E5253 Governor Control Assembly{1265}
Heavy Duty Jackstand Arrangement{0630} Heavy Duty Jackstand Arrangement{0630}
Procedure for Handling, Cleaning, Assembly, Installation and Protection of Service Replacement Crankshafts for 3600 Family Engines{1202} Procedure for Handling, Cleaning, Assembly, Installation and Protection of Service Replacement Crankshafts for 3600 Family Engines{1202}
Adjustment Procedure for Cab Door Latch Assemblies and Strikers{7301, 7308} Adjustment Procedure for Cab Door Latch Assemblies and Strikers{7301, 7308}
Reconditioning of 2W8903 and/or 7W8003 Junction Box Groups{7426} Reconditioning of 2W8903 and/or 7W8003 Junction Box Groups{7426}
Installation of Electric Starting Motors{1453} Installation of Electric Starting Motors{1453}
Installation and Use of 4C5818 Collar and Retainer Group{1000} Installation and Use of 4C5818 Collar and Retainer Group{1000}
Marine Par Curve Development{1000} Marine Par Curve Development{1000}
Replacement of 7C2662, 7C2664 or 7C3507 VR3 Voltage Regulators{4467} Replacement of 7C2662, 7C2664 or 7C3507 VR3 Voltage Regulators{4467}
Installation of 4P0705 Exhaust Restricter Retrofit Kit{1050} Installation of 4P0705 Exhaust Restricter Retrofit Kit{1050}
Using the 7X1400 Digital Diagnostic Tool (DDT) Group{0781, 0782} Using the 7X1400 Digital Diagnostic Tool (DDT) Group{0781, 0782}
Rework of New Primary Fuel Filter and Supply Lines{1260, 1274} Rework of New Primary Fuel Filter and Supply Lines{1260, 1274}
3406B PEEC Personality Module Update{0781, 0782} 3406B PEEC Personality Module Update{0781, 0782}
Assembly And Use Of 4C6601 Hose Press Stand{0684} Assembly And Use Of 4C6601 Hose Press Stand{0684}
Using the 4C6710 Governor Test Unit Group{0782, 1264} Using the 4C6710 Governor Test Unit Group{0782, 1264}
Installation of Fuel Injection Pump and Governor Service Group{1286} Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation of Switches/Sensors With Sure-Seal Connectors{7332} Installation of Switches/Sensors With Sure-Seal Connectors{7332}
Installation Of Auxiliary Oil Filter Groups{1306} Installation Of Auxiliary Oil Filter Groups{1306}
Installation and Adjustment of 3161 Governor on 3500 Family of Engines{1264} Installation and Adjustment of 3161 Governor on 3500 Family of Engines{1264}
Operator Instruction Card For The Automatic Ether Injection System (AEIS){1456} Operator Instruction Card For The Automatic Ether Injection System (AEIS){1456}
Procedures for Using Portable Filter Carts{0680, 5068} Procedures for Using Portable Filter Carts{0680, 5068}
Installation of 9Y9345 Rear Gear Group With 4W0014 or 1W0024 Rear Housing{1204, 1206, 1212} Installation of 9Y9345 Rear Gear Group With 4W0014 or 1W0024 Rear Housing{1204, 1206, 1212}
Using 9U-6860 Tool Group To Replace Unit Injector Sleeves{1290} Using 9U-6860 Tool Group To Replace Unit Injector Sleeves{1290}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.