Field Installation of the 223-8416 Installation Arrangement (Air Conditioner Conversion) {7304, 7320} Caterpillar

Skid Steer Loader:

236 (S/N: 4YZ1-UP)

252 (S/N: FDG1-UP)

262 (S/N: CED1-UP)

Multi Terrain Loader:

277 (S/N: CNC1-UP)

287 (S/N: CNY1-UP)

Introduction

Reference: Operation and Maintenance Manual, SEBU7468, "216, 226, 228, 236, 246, 248, 252, and 262 Skid Steer Loaders"

Reference: Operation and Maintenance Manual, SEBU7494, "247, 257, 267 and 277 Multi Terrain Loaders"

Reference: Disassembly and Assembly Manual, REHR2877, "Machine Systems - 236 and 246 Skid Steer Loaders"

Reference: Disassembly and Assembly Manual, REHR4812, "Machine Systems - 236, 246, 252, and 262 Skid Steer Loaders"

Reference: Disassembly and Assembly Manual, REHR4815, "Machine Systems - 267 and 277 Multi Terrain Loaders"

Reference: Testing and Adjusting, SENR5664, "Air Conditioning and Heating R-134a for All Caterpillar Machines"

This Special Instruction provides the information that is necessary for the installation of the 222-5722 Installation Arrangement (Air Conditioner and Heater). This kit contains all of the parts that are needed for field installation of the air conditioner and heater.

Do not perform any procedure or do not order any parts until you have read the information that is contained in this instruction.

Parts Needed

Air Conditioner and Heater

The parts that are needed for installation of the 222-5722 Installation Arrangement (Air Conditioner and Heater) are identified in Table 1 and in Table 2.

Table 1

Air Conditioner and Heater
Item	Quantity	Part Number	Description
1	1	1P-6356	Plate
2	1	2P-6818	V-Belt
3	29	3S-2093	Cable Strap
4	1	4P-8134	Clip
5	3	4S-1962	Clip
6	6	5C-2890	Nut
7	2	5C-9553	Bolt
8	3	5P-4116	Hard Washer
9	1	216-4970	Circuit Breaker (120 Amp)
10	10	7K-1181	Cable Strap
11	2	7X-0579	Hard Washer
12	2	7X-7729	Washer
13	1	8T-0342	Bolt
14	21	8T-4121	Hard Washer
15	5	8T-4133	Nut
16	2	8T-4136	Bolt
17	3	8T-4189	Bolt
18	2	8T-4196	Bolt
19	4	8T-4200	Bolt
20	24	8T-4205	Hard Washer
21	7	8T-4224	Hard Washer
22	2	8T-5436	Bolt
23	1	8T-6466	Bolt
24	1	8T-7586	Bolt
25	1	9R-5383	Boss
26	11	9X-2045	Screw
27	1	9X-7378	O-Ring Seal
28	3	101-2867	Hard Washer
29	1	113-8492	Fuse (20 Amp)
30	1	114-5333	Pressure Switch (Refrigerant)
31	1	125-2796	Fitting As
32	1	142-9290	Filter Cover
33	1	142-9291	Filter
34	1	152-4876	Seal
35	4	199-6619	Clinch Stud
36	1	203-5492	Alternator Gp
37	1	216-6152	Bracket
38	5	218-0666	Louver As
39	1	218-4994	Refrigerant Compressor Gp
40	1	219-4359	Duct
41	1	219-4360	Duct
42	231 cm (91 inch)	219-4361	Tubing
43	1	219-4362	Cover (RH)
44	1	219-4363	Cover (LH)
45	1	219-4368	Bracket
46	1	219-4369	Bracket
47	1	219-4373	Bracket
48	1	227-5918	Belt Guard
49	1	219-4392	Bracket
50	1	219-7182	Air Conditioner Gp
51	1	220-5527	Harness
52	1	220-5528	Harness
53	1	220-8139	Bracket
54	2	090-9434	Spacer
55	1	220-8129	V-Belt
56	1	224-6208	Threaded Insert
57	1	225-0297	Fitting As
58	2	2W-1745	Spacer
59	5	5C-7261	Nut
60	70 cm (28 inch)	5N-8359	Flexible Conduit
61	30 cm (12 inch)	5P-0802	Seal
62	4	6D-1641	Clip
63	6	6V-7357	Bolt
64	1	8T-4178	Bolt
65	4	8T-4195	Bolt
66	2	8T-4198	Bolt
67	2	8T-4908	Bolt
68	1	8T-5005	Bolt
69	2	8V-3032	Spacer
70	1	9D-1829	Clip
71	1	9X-7380	O-Ring Seal
72	4	9X-7381	O-Ring Seal
73	2	9X-7382	O-Ring Seal
74	2	9X-7383	O-Ring Seal
75	2	101-8296	Clip
76	6	129-3178	Locknut
77	1	186-6190	Refrigerant Accumulator
78	1	219-4341	Hose As
79	1	219-4342	Hose As
80	1	219-4343	Hose As
81	1	219-4344	Hose As
82	1	219-4349	Bracket
83	1	220-0163	Suction Fan Gp
84	1	220-8119	Bracket
85	1	220-8131	Blower Fan Gp
86	1	220-8134	Orifice Tube As
87	1	220-8155	Condenser Coil As
88	1	225-9240	Plate
89	1	225-9241	Insulation
90	1	1L-2279	Elbow
91	1	5K-6875	Adapter
92	1	8F-8151	Shutoff Valve
93	4	8T-0154	Hose Clamp
94	10	9X-2092	Edge Strip
95	1	004-6810	Elbow
96	452 cm (178 inch)	136-1953	Hose
97	2	183-7120	Hose Guard
98	1	219-4328	Elbow
99	1	4W-7627	Spacer
100	1	162-5233	Film (Work Tool Control)
101	4	8T-4138	Bolt
102	1	223-9636	Instruction Plate
103	1	219-4326	Hose
104	1	219-4327	Bracket
105	2	4B-4274	Washer
106	2	5L-4507	Screw

Table 2

Miscellaneous
Quantity		Part Number	Description
-		5P-3413	Pipe Sealant
-		228-7840	Air Conditioner Lubricant
-		-	Refrigerant Gas R134a

Seat Belt

In order to accommodate the new air conditioner and heater unit, the current seat belt must be replaced. The new seat belts that are available are listed in Table 3.

Table 3

New Seat Belts
Quantity	Part Number	Description
1	220-8080	Seat Belt (2 inch) (1)
1	220-8082	Seat Belt (2 inch) (2)
1	220-8081	Seat Belt (3 inch) (1)
1	220-8084	Seat Belt (3 inch) (2)

( 1 )	Static Seat
( 2 )	Suspension Seat

Preparing the Machine

1. Park the machine on level ground.

2. Raise the lift arms fully and engage the loader lift arm brace.

3. Turn the engine start switch key to the OFF position.

Modifying the Support Assemblies for the Joysticks

Show/hide table



Illustration 1	g00941494
(A) Left Hand Support Assembly (B) Right Hand Support Assembly (C) Vertical Floorplate

1. Remove the vertical floorplate (C) that is between the left hand support assembly (A) and the right hand support assembly (B). See Illustration 1.

   Retain the vertical floorplate.

   Retain the two bolts and the two hard washers.

Show/hide table



Illustration 2	g00944235
The left hand support assembly (A) 90 ± 1.5 mm (3.5 ± 0.06 inch) (B) 191 ± 1.5 mm (7.5 ± 0.06 inch) (C) 36 ± 1.5 mm (1.4 ± 0.06 inch) Radius (D) 4 ± 1.5 mm (0.16 ± 0.06 inch) (E) 75 ± 1.5 mm (3.0 ± 0.06 inch) (F) 25 ± 1.5 mm (0.9 ± 0.06 inch) Radius (G) 38.8 ± 1.5 mm (1.5 ± 0.06 inch) Radius (H) 75 ± 1.5 mm (3.0 ± 0.06 inch)

2. Cut the left hand support assembly (A) in order to provide cutout (1), cutout (2), and cutout (3), as shown. See Illustration 2.

Show/hide table



Illustration 3	g00943043
The right hand support assembly (J) 151 ± 1.5 mm (5.9 ± 0.06 inch) (K) 228 ± 1.5 mm (8.9 ± 0.06 inch) (L) 154 ± 1.5 mm (6.1 ± 0.06 inch) (M) 4 ± 1.5 mm (0.16 ± 0.06 inch) (N) 12.9 ± 1.5 mm (0.51 ± 0.06 inch) Radius

3. Cut the right hand support assembly (B ) in order to provide cutout (4), as shown. See Illustration 3.

Show/hide table



Illustration 4	g00948840
Enlarge the existing hole in the top of the right support assembly (B) in order to accommodate the new duct. (P) 8 ± 1.5 mm (0.32 ± 0.06 inch) (Q) 6 ± 1.5 mm (0.24 ± 0.06 inch) (R) 16 ± 1.5 mm (0.63 ± 0.06 inch)

4. Also, enlarge the hole in the top of the right hand support assembly (B). See Illustration 4.

   Note: Cut and remove area (5), area (6), and area (7) .

5. Perform Step 5.a through Step 5.r in order to install the tubing, the ducts, and the louvers.
   Show/hide table
   
   

   Illustration 5	g00941546
   (A) Left Hand Support Assembly (B) Right Hand Support Assembly (10) 7K-1181 Cable Strap (26) 9X-2045 Screw (38) 218-0666 Louver As (40) 219-4359 Duct (41) 219-4360 Duct (42) 219-4361 Tubing (43) 219-4362 Cover (RH) (44) 219-4363 Cover (LH)

   1. Place the 231 cm (91 inch) length of 219-4361 Tubing (42) on a flat surface. Cut the tubing into the following lengths.
      • Three 31 cm (12 inch) lengths

      • Two 69 cm (27 inch) lengths

   2. Assemble two 31 cm (12 inch) lengths of tubing to the 219-4359 Duct (40). See Illustration 5.

      Secure the tubing to the duct with two 7K-1181 Cable Straps (10) .

   3. Insert the duct with the two lengths of tubing into the opening that is provided in the top of the right hand support assembly (B) .

   4. Install the 219-4362 Cover (RH) (43) on the front of the right hand support assembly (B) .

      Install the cover with four 9X-2045 Screws (26) .

      Tighten the screws to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

   5. Pull the ends of the tubing through the two openings in the cover.

   6. Install a 218-0666 Louver As (38) on the end of each length of tubing. Secure each louver assembly to the tubing with a 7K-1181 Cable Strap (10) .

      Note: Cut one coil of the tubing's helix in order to facilitate installation of the louver. Then install the cable strap beyond the cut in order to keep the cut from continuing.

   7. Seat the two louver assemblies in the openings on the 219-4362 Cover (RH) (43) .

      Note: The louver assemblies will snap into position in the openings that are provided on the cover.

   8. Assemble the three lengths of tubing that remain to the 219-4360 Duct (41) .

      Note: Install the 31 cm (12 inch) length of tubing in the front position of duct (41), as shown. See Illustration 5.

      Secure each length of tubing to the duct with a 7K-1181 Cable Strap (10) .

   9. Insert the three lengths of tubing that are assembled on the 219-4360 Duct (41) into cutout (1) in the left hand support assembly (A) .

   10. Also, push the end of the 219-4360 Duct (41) into cutout (1) in the left hand support assembly (A) .

   11. Then, fit the opposite end of the 219-4360 Duct (41) into opening (4) in the base of the right hand support assembly (B). See Illustration 5.

       Note: This end of the 219-4360 Duct (41) will fit over the end of the 219-4359 Duct (40) which is inside the right hand support assembly (B) .

   12. Install the 219-4363 Cover (LH) (44) on the front of the left hand support assembly (A) .

       Install the cover with four 9X-2045 Screws (26) .

       Tighten the screws to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

   13. Pull the end of two lengths of tubing through the openings in the cover.

       Note: For maximum air flow, route the tubing that is in the center position of duct (41) to the top opening in the cover, as shown. See Illustration 5.

   14. Install a 218-0666 Louver As (38) on the end of the two lengths of tubing. Secure each louver assembly to the tubing with a 7K-1181 Cable Strap (10) .

       Note: Cut one coil of the tubing's helix in order to facilitate installation of the louver. Then install the cable strap beyond the cut in order to keep the cut from continuing.

   15. Seat the two louver assemblies in the openings on the 219-4363 Cover (LH) (44) .

       Note: The louver assemblies will snap into position in the openings that are provided on the cover.

   16. Pull the end of the remaining length of tubing through cutout (3) in the left hand support assembly (A) .

   17. Install a 218-0666 Louver As (38) on the end of the tubing. Secure the louver assembly to the tubing with a 7K-1181 Cable Strap (10) .

       Note: Cut one coil of the tubing's helix in order to facilitate installation of the louver. Then install the cable strap beyond the cut in order to keep the cut from continuing.

   18. Seat the louver assembly in the cutout in the left hand support assembly (A) .

       Note: The louver assembly will snap into position in the cutout in the left hand support assembly.

6. Reinstall the 154-3965 Floorplate (Vertical) (D) between the left hand support assembly (A) and the right hand support assembly (B). See Illustration 1.

   Use the three 8T-4205 Hard Washers and the three 5C-9553 Bolts that were removed in Step 1.

   Tighten the bolts to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

Installing the Cab Air Filter

Show/hide table



Illustration 6	g00920073
Remove the plate.

1. If equipped, remove the plate that is indicated in Illustration 6. Remove the plate by removing the four nuts and the four washers that secure the plate to the cab. Also, remove the four studs.

Show/hide table



Illustration 7	g00925699
Assemble the cab air filter and install the cab air filter. (6) 5C-2890 Nut (20) 8T-4205 Hard Washer (32) 142-9290 Filter Cover (33) 142-9291 Filter (34) 152-4876 Seal

2. Assemble the 142-9290 Filter Cover (32), the 142-9291 Filter (33), and the 152-4876 Seal (34). See Illustration 7.

   Note: To install seal (34), remove the protective paper strip from the seal and press the seal firmly against the cover.

3. Install the four 199-6619 Clinch Studs (35).

   Note: Press fit the new studs from the inside of the cab.

Show/hide table



Illustration 8	g00920087
The cab air filter

4. Place the assembled cab air filter in position on the four 199-6619 Clinch Studs (35). See Illustration 8.

   Secure the cab air filter with four 5C-2890 Nuts (6) and four 8T-4205 Hard Washers (20) .

   Tighten the nuts to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

5. Disengage the loader lift arm brace and lower the lift arms fully.

Installing the Air Conditioner and Heater

Show/hide table



Illustration 9	g00920095
Remove the plate.

1. Remove the plate that is identified in Illustration 9.

   Remove the plate by removing the four screws, the four hard washers, and the four nuts that secure the plate to the cab floor.

Show/hide table



Illustration 10	g00927520
View of the bottom of the cab (E) Cut and remove the insulating material. (F) Remove the cable strap and the cap.

2. Cut and remove the portion of insulating material (E) from the bottom of the cab. Also remove the cable strap and the cap (F) from the harness connector. See Illustration 10.

3. Place the 219-7182 Air Conditioner Gp (50) in position inside the cab.

Show/hide table



Illustration 11	g00938878
(20) 8T-4205 Hard Washer (101) 8T-4138 Bolt

4. Install four 8T-4138 Bolts (101) and four 8T-4205 Hard Washers (20) in order to mount the air conditioner and heater unit to the cab floor. See Illustration 11.

   Tighten the bolts to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

Show/hide table



Illustration 12	g00927475
(72) 9X-7381 O-Ring Seal (86) 220-8134 Orifice Tube As

5. Install the 220-8134 Orifice Tube As (86). Use a 9X-7381 O-Ring Seal (72) in the connection. See Illustration 12.

   Note: Lubricate the O-ring seal with a mineral based refrigerant oil that is compatible with the R134a refrigerant.

   Tighten the connector to a torque of 27 ± 4 N·m (20 ± 3 lb ft).

6. Connect the triangular shaped plug to the triangular shaped receptacle. Secure this connection with a 3S-2093 Cable Strap (3) .

   Note: The remaining connector, which is addressed later in this instruction, mates to a connector on the 220-5527 Harness (Cab ) (51).

Installing the Condenser

Show/hide table



Illustration 13	g00927445
(20) 8T-4205 Hard Washer (63) 6V-7357 Bolt (69) 8V-3032 Spacer (76) 129-3178 Locknut (83) 220-0163 Suction Fan Gp (85) 220-8131 Blower Fan Gp (87) 220-8155 Condenser Coil As

1. Install the 220-8131 Blower Fan Gp (85) to the 220-8155 Condenser Coil As (87). The blower fan is installed on the front side of the condenser. See Illustration 13.

   Note: The front side of the condenser contains the mounting flange with three weld studs for mounting the coil.

   Use two 6V-7357 Bolts (63), four 8T-4205 Hard Washers (20), two 8V-3032 Spacers (69), and two 129-3178 Locknuts (76) .

   Tighten the locknuts to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

2. Install the 220-0163 Suction Fan Gp (83) to the 220-8155 Coil (87). The suction fan is installed on the rear side of the condenser. See Illustration 13.

   Use four 6V-7357 Bolts (63), four 8T-4205 Hard Washers (20), and four 129-3178 Locknuts (76). See the inset in Illustration 13 for details.

   Tighten the locknuts to a torque of 12 ± 3 N·m (9 ± 2 lb ft).

Show/hide table



Illustration 14	g00927448
(21) 8T-4224 Hard Washer (59) 5C-7261 Nut (67) 8T-4908 Bolt (84) 220-8119 Bracket

3. Install the condenser in the engine compartment in the opening that is provided on the firewall. See Illustration 14.

   Note: The condenser is installed with the blower fan to the front of the machine.

   Show/hide table
   
   

   Illustration 15	g00940354
   Locating dimensions for mounting holes (R) 10.5 mm (0.4 inch) (S) 80.2 mm (3.2 inch) (T) 119.6 mm (4.7 inch)

   1. Position the condenser so that the two weld studs on the left mounting flange extend through the two holes that are provided on the left side of the opening in the firewall.

      Note: For machines without holes on the left side of the firewall, drill two 9.0 mm (0.4 inch) holes per Illustration 15.

      Install two 5C-7261 Nuts (59) and two 8T-4224 Hard Washers (21) on the two weld studs in order to hold the condenser in place.

   2. From the front of the firewall, place the 220-8119 Bracket (84) on the remaining weld stud. Install a 5C-7261 Nut (59) and a 8T-4224 Hard Washer (21) on the weld nut in order to hold the bracket in place.

   3. Place a 8T-4224 Hard Washer (21) on a 8T-4908 Bolt (67). Then insert the 8T-4908 Bolt (67) through the hole in the mounting flange and through the hole in the bracket. Install a 5C-7261 Nut (59) and a 8T-4224 Hard Washer (21) on the bolt.

   4. Complete the installation of the condenser by tightening all four of the nuts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).

Show/hide table



Illustration 16	g00927449
(6) 5C-2890 Nut (7) 5C-9553 Bolt (20) 8T-4205 Hard Washer (88) 225-9240 Plate (89) 225-9241 Insulation

4. Install the 225-9241 Insulation (89) on the 225-9240 Plate (88). See Illustration 16.

   Note: Remove the protective strip from the back of the insulation and press the insulation on the plate.

5. On the inside of the engine compartment, install the 225-9240 Plate (88) on the left side of the condenser coil.

   Use two 5C-9553 Bolts (7), four 8T-4205 Hard Washers (20), and two 5C-2890 Nuts (6) for mounting the plate.

   Tighten the nuts to a torque of 12 ± 3 N·m (9 ± 22 lb ft).

Modifying the Air Lines Group

Note: For machines without turbochargers, perform Step 1. For machines with turbochargers, perform Step 1 and Step 2.

1. Modify the mounting of the air cleaner on the left wall of the engine compartment.
   Show/hide table
   
   

   Illustration 17	g00932236
   The air cleaner (N)

   1. Temporarily remove the air cleaner (N) from the left wall of the engine compartment. See Illustration 17.

      Retain the two 8T-4908 Bolts and the two 5P-4116 Hard Washers .

   Show/hide table
   
   

   Illustration 18	g00941611
   (53) 220-8139 Bracket (54) 090-9434 Spacer (59) 5C-7261 Nut (67) 8T-4908 Bolt

   2. Install the 220-8139 Bracket (53) on the left wall of the engine compartment. See Illustration 18.

      Use the two 090-9434 Spacers (54) that are provided in this kit and use the 8T-4908 Bolts and the two 5P-4116 Hard Washers that were removed in Step 1.a.

      Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).

   3. Reinstall the air cleaner (N) on the 220-8139 Bracket (53). See Illustration 18.

      Use a 8T-4908 Bolt (67) to secure the air cleaner at the top of the bracket. Tighten the bolt to a torque of 28 ± 7 N·m (21 ± 5 lb ft).

      Use a 5C-7261 Nut (59) to secure the air cleaner at the bottom of the bracket. Tighten the nut to a torque of 28 ± 7 N·m (21 ± 5 lb ft).

2. Modify the mounting of the inlet elbow assembly.
   Show/hide table
   
   

   Illustration 19	g00932235
   (M) Turbocharger (N) Air Cleaner (O) Hose (P) Bracket

   1. Remove the existing hose (O) and remove the existing bracket (P). Retain all of the mounting hardware. Discard the hose and the bracket. See Illustration 19.
   Show/hide table
   
   

   Illustration 20	g00932240
   (M) Turbocharger (N) Air Cleaner (103) 219-4326 Hose (104) 219-4327 Bracket

   2. Install the 219-4327 Bracket (104). See Illustration 20.

      Use the two engine lift eye bolts in order to install the bracket. Tighten these bolts to a torque of 15 ± 3 N·m (11 ± 2 lb ft).

      Reuse the 6V-8210 Bolt and the 8T-4224 Hard Washer in order to reinstall the inlet elbow assembly. Tighten this bolt to a torque of 15 ± 3 N·m (11 ± 2 lb ft).

   3. Install the 219-4326 Hose (103) .

      Reuse the two 5P-0597 Hose Clamps that were removed in Step 2.a in order to secure the hose. Tighten the hose clamps to a torque of 7.5 ± 0.5 N·m (5.5 ± 0.4 lb ft).

Modifying the Muffler

Illustration 21	g00935866
Rear view of the muffler

1. For machines without turbochargers, grind the rear lip of the muffler in order to provide additional clearance for the alternator wiring. Remove material between the 5 o'clock position and the 8 o'clock position, as shown. See Illustration 21.

   Note: Remove material to the end cap of the muffler. Do not penetrate the end cap.

2. Paint the area that was modified in order to prevent rusting.

3. For 236 machines, rotate the muffler clamp for 45° so that the clamp bolt is to the rear of the machine.

Installing the Compressor and the Alternator

Show/hide table

Disconnect batteries before performance of any service work.

Show/hide table

NOTICE
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Show/hide table



Illustration 22	g00927450
(E) Belt Guard (F) V-Belt (G) Bracket (H) Bracket (J) Alternator

1. Remove belt guard (E), V-belt (F), and alternator (J) from the engine. See Illustration 22.

   See the "Alternator Removal Procedure" in the engine section of the Disassembly and Assembly Manual for your machine.

2. Also, remove bracket (G) and bracket (H) .

   Note: Discard these components with the mounting hardware that was removed.

Show/hide table



Illustration 23	g00927451
(2) 2P-6818 V-Belt (8) 5P-4116 Hard Washer (12) 7X-7729 Washer (13) 8T-0342 Bolt (14) 8T-4121 Hard Washer (15) 8T-4133 Nut (17) 8T-4189 Bolt (18) 8T-4196 Bolt (22) 8T-5436 Bolt (24) 8T-7586 Bolt (25) 9R-5383 Boss (37) 216-6152 Bracket (39) 218-4994 Refrigerant Compressor Gp (45) 219-4368 Bracket (46) 219-4369 Bracket

Show/hide table



Illustration 24	g00927452
(8) 5P-4116 Hard Washer (14) 8T-4121 Hard Washer (15) 8T-4133 Nut (17) 8T-4189 Bolt (36) 203-5492 Alternator Gp (47) 219-4373 Bracket (55) 220-8129 V-Belt (66) 8T-4198 Bolt

Show/hide table



Illustration 25	g00931628
(B) 19° ± 2° (1) 1P-6356 Plate (3) 3S-2093 Cable Strap (4) 4P-8134 Clip (23) 8T-6466 Bolt (27) 9X-7378 O-Ring Seal (30) 114-5333 Pressure Switch (31) 125-2796 Fitting As (57) 225-0297 Fitting As

3. Assemble the 218-4994 Refrigerant Compressor Gp .

   1. Remove the protective cap from the compressor in order to access the suction inlet port and the discharge pressure port.

   2. Place the 125-2796 Fitting As (31) in the suction inlet port and place the 225-0297 Fitting As (57) in the discharge pressure port. Then position the 1P-6356 Plate (1) over the two fittings. See Illustration 25.

   3. Assemble the 4P-8134 Clip (4) onto the 8T-6466 Bolt (23). Then install the bolt in the compressor in order to secure the two fittings and the clip.

      Tighten the bolt to a torque of 30 ± 7 N·m (22 ± 5 lb ft).

   4. Install the 114-5333 Pressure Switch (30) in the side port of the 225-0297 Fitting As (57). See Section A-A of Illustration 25.

      Use a 9X-7378 O-Ring Seal (27) in the installation of the pressure switch.

      Note: Lubricate the O-ring seal with a mineral based refrigerant oil that is compatible with the R134a refrigerant.

      Tighten the switch assembly to a torque of 8 ± 1.5 N·m (5.9 ± 1.1 lb ft).

4. Assemble the 218-4994 Refrigerant Compressor Gp (39) to the 216-6152 Bracket (Compressor Support) (37). See Illustration 23.

   1. Insert a 8T-5436 Bolt (22) through a 8T-4121 Hard Washer (14), through the rear mounting flange on the top of the compressor, and through the boss that is provided on the 216-6152 Bracket (Compressor Support) (37) .

   2. Continue to insert the bolt through the front mounting flange on the top of the compressor and into the weld nut on the 219-4373 Bracket (Alternator Adjustment) (47). See Illustration 23 and Illustration 24.

      Note: Do not tighten the bolt fully.

5. Secure the 219-4369 Bracket (Compressor Adjustment) (46) to the two front mounting flanges on the bottom of the compressor. See Illustration 23.

   1. Insert a 8T-4196 Bolt (18) through two 8T-4121 Hard Washers (14) and through the mounting flange.

      Note: The bolt must be inserted from the rear of the mounting flange.

   2. Continue to insert the bolt through two 8T-4121 Hard Washers (14) and into the weld nut on the 219-4369 Bracket (Compressor Adjustment) (46) .

   3. Repeat Step 5.a and Step 5.b in order to secure the bracket to the remaining front mounting flange on the bottom of the compressor.

   4. Tighten the two bolts to a torque of 30 ± 3 N·m (22 ± 2 lb ft).

6. Install the 219-4368 Bracket (Alternator Support) (45) on the compressor. See Illustration 23.

   1. Insert a 8T-5436 Bolt (22) through a 8T-4121 Hard Washer (14), through the rear flange on the top of the compressor, and through the 219-4368 Bracket (Alternator Support) (45) .

   2. Continue to insert the bolt through the front flange on the top of the compressor and into the weld nut on the 219-4369 Bracket (Compressor Adjustment) (46) .

      Note: Do not tighten the bolt at this point fully.

7. Mount the compressor assembly to the engine block. See Illustration 23.

   1. Hold the compressor assembly in place on the engine. At Location (A), install a 8T-0342 Bolt (13) and a 8T-4121 Hard Washer (14) in order to secure the front of the support bracket to the engine block.

   2. At Location (B), install a 8T-4189 Bolt (17) and a 5P-4116 Hard Washer (8) in order to secure the side of the support bracket to the engine block.

   3. Raise the compressor in order to access the lower mounting hole. At Location (C), install a 8T-4189 Bolt (17) and a 5P-4116 Hard Washer (8) in order to secure the side of the support bracket to the engine block.

   4. First, tighten the front mounting bolt to a torque of 30 ± 3 N·m (22 ± 2 lb ft). Then, tighten the two side mounting bolts to a torque of 30 ± 3 N·m (22 ± 2 lb ft).

8. Install the V-belt. See Illustration 23.

   1. Position the 2P-6818 V-Belt (2) around the three pulleys.

   2. Insert a 8T-7586 Bolt (24) through a 7X-7729 Washer (12) and through the compressor adjustment bracket (46) .

   3. Then insert the bolt through the 9R-5383 Boss (25) and the hole in the timing case at Location (D) .

   4. Secure the bolt with a 5P-4116 Hard Washer (12) and a 8T-4133 Nut (15) .

      Note: Tighten the bolt so that the compressor is secure, but the compressor can be moved in order to tension the V-belt.

9. Tension the V-belt.

   Refer to the procedure for adjusting the tension of the V-Belt in the Operation and Maintenance Manual for your machine.

   The tension that is recommended for the V-belt is provided in Table 4.

   Show/hide table

   Table 4

   Belt	Belt Tension
   	Initial (1)	Used (2)
   5L-3834 V-Belt	534 ± 22 N (120 ± 5 lb)	400 ± 44 N (90 ± 10 lb)

   Show/hide table

   ( 1 )	A new belt
   ( 2 )	A belt is considered to be used after 30 minutes of operation.

   Note: Tension the V-belt again after 30 minutes of operation at the rated speed.

   Show/hide table

   Table 5

   Recommended Tooling
   Part Number	Description
   144-0235	Belt Tension Gauge

   Note: When you tension the V-belt, keep the tension bar parallel to the adjustment bracket plate in order to prevent bending of the bracket.

   1. Tension the V-belt.

   2. Maintain V-belt tension and tighten the 8T-7586 Bolt (24) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

10. At Location (E), loosen the 124-6264 Hose Clamp for the radiator hose. See Illustration 24.

    Rotate the hose clamp for 90° in order to prevent interference with the new alternator. Tighten the hose clamp to a torque of 12 ± 1 N·m (9 ± 1 lb ft).

11. Install the new alternator. See Illustration 24.

    1. Place the 203-5492 Alternator Gp (36) in position. Install a 8T-4198 Bolt (66), two 8T-4121 Hard Washers (14), and a 8T-4133 Nut (15) in order to secure the alternator in position. Hand tighten the nut.

    2. Place the 220-8129 V-Belt (55) around the two pulleys.

    3. Install the 8T-4189 Bolt (17) and the 5P-4116 Hard Washer (8) in the top flange of the alternator in order to loosely secure the alternator.

    4. Adjust the tension of the alternator belt. Use a long screwdriver with a thick shaft in order to tension the V-belt. For leverage, position the screwdriver between the top of the compressor and the alternator on the engine side of the alternator adjustment bracket. See Table 4 for the recommended belt tension.

    5. Maintain belt tension. Secure the alternator by tightening the 8T-4189 Bolt (17) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).

    6. Tighten the 8T-4198 Bolt (66) that secures the alternator to the alternator support bracket (45). This bolt was hand tightened in Step 11.

       Tighten the bolt to a torque of 30 ± 7 N·m (22 ± 5 lb ft).

    7. Tighten the 8T-5436 Bolt (22) into the weld nut on the alternator adjustment bracket (47). This bolt was hand tightened in Step 4.

       Tighten this bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

    8. Tighten the 8T-5436 Bolt (22) into the weld nut on the compressor adjustment bracket (46). Bolt (22) was hand tightened in Step 6.

       Tighten the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

Installing the Air Conditioner Lines

Show/hide table



Illustration 26	g00938867
(71) 9X-7380 O-Ring Seal (72) 9X-7381 O-Ring Seal (73) 9X-7382 O-Ring Seal (74) 9X-7383 O-Ring Seal (77) 186-6190 Refrigerant Accumulator (78) 219-4341 Hose As (79) 219-4342 Hose As (80) 219-4343 Hose As (81) 219-4344 Hose As

Show/hide table



Illustration 27	g00927866
Assembling and mounting the accumulator (14) 8T-4121 Hard Washer (58) 2W-1745 Spacer (61) 5P-0802 Seal (65) 8T-4195 Bolt (66) 8T-4198 Bolt (75) 101-8296 Clip (77) 186-6190 Refrigerant Accumulator (82) 219-4349 Bracket

1. Assemble the 186-6190 Refrigerant Accumulator (77) to the 219-4349 Bracket (82). See Illustration 26 and Illustration 27.

   1. Install a 150 mm (6 inch) length of the 5P-0802 Seal (61) on the concave surface of both 101-8296 Clips (75) .

      Note: Remove the protective strip from the back of the seal and press the seal to the clips.

   2. Place the clips around the 186-6190 Refrigerant Accumulator (77) so that the two clips encircle the body of the accumulator.

      Note: Position the accumulator in the clips per Illustration 31 or Illustration 32.

   3. Align the mounting holes in the two clips with the mounting holes in the bosses that are provided on the 219-4349 Bracket (82) .

      Secure the accumulator to the bracket with two 8T-4195 Bolts (65) and two 8T-4121 Hard Washers (14). Hand tighten the two bolts at this time.

2. Install the accumulator in the engine compartment by mounting the 219-4349 Bracket (82) to the firewall. See Illustration 27.

   Use a 8T-4198 Bolt (66) and a 8T-4121 Hard Washer (14) with a 2W-1745 Spacer (58) for mounting the bracket.

   Note: Use the left mounting tab that is provided in the opening in the firewall. Place the washer on the bolt. From outside of the engine compartment, insert the bolt through the hole in the mounting tab and then insert the bolt through the spacer. Install the bolt in the threaded boss that is provided on the top of the bracket.

3. Install the 219-4343 Hose As (80) between the air conditioner and the condenser. See Illustration 26.

   Note: Lubricate all O-ring seals that are used in this procedure with a mineral based refrigerant oil that is compatible with the R134a refrigerant.

   Show/hide table
   
   

   Illustration 28	g00928045
   Bottom view of air conditioner and heater (62) 6D-1641 Clip (72) 9X-7381 O-Ring Seal (73) 9X-7382 O-Ring Seal (79) 219-4342 Hose As (80) 219-4343 Hose As

   1. Connect the end of hose assembly (80) with the 90° stem to the 220-8134 Orifice Tube As (86) that is installed on the inlet of the air conditioner. See Illustration 28.

      Use a 9X-7381 O-Ring Seal (72) for this connection.

      Tighten the coupling to a torque of 27 ± 4 N·m (20 ± 3 lb ft).

   2. Route hose assembly (80) per Illustration 26.

   3. Connect the end of hose assembly (80) with the 45° stem to the outlet of the condenser. The outlet is the bottom connector on the right side of the condenser. Use a 9X-7380 O-Ring Seal (71) for this connection.

      Tighten the coupling to a torque of 14 ± 4 N·m (10 ± 3 lb ft).

4. Install the 219-4342 Hose As (79) between the air conditioner and the accumulator. See Illustration 26.

   1. Connect the end of hose assembly (79) with the long 90° stem to the outlet for the air conditioner. Use a 9X-7382 O-Ring Seal (73) for this connection.

      Tighten the coupling to a torque of 40 ± 4 N·m (30 ± 3 lb ft).

   2. Route hose assembly (79) per Illustration 26.

   3. Connect the end of hose assembly (79) with the short 90° stem to the inlet for the accumulator. The inlet is the connection on the body of the accumulator. Use a 9X-7383 O-Ring Seal (74) for this connection.

      Note: Orient the hose coupling per Illustration 31 or Illustration 32.

      Tighten the coupling to a torque of 45 ± 5 N·m (33 ± 4 lb ft).

Show/hide table



Illustration 29	g00931413
Securing the hose assemblies (14) 8T-4121 Hard Washer (15) 8T-4133 Nut (62) 6D-1641 Clip (65) 8T-4195 Bolt (70) 9D-1829 Clip

5. Secure hose assembly (80) and hose assembly (79). See Illustration 29.

   1. At Location (G), secure the two hose assemblies to the mounting stud on the back wall of the cab.

      Use a 6D-1641 Clip (62), a 8T-4121 Hard Washer (14), and a 8T-4133 Nut (15) .

      Note: Do not tighten the bolt fully at this point.

   2. At Location (H), secure the two hose assemblies to the threaded boss.

      Note: For machines without a threaded boss at Location (H), go to Step 5.c.

      Use a 9F-1829 Clip (70), a 8T-4121 Hard Washer (14), and a 8T-4195 Bolt (65) to secure the hose assemblies.

      Note: Secure the end of the hose guard that is provided on the hose assembly inside the 9D-1829 Clip (70). Install the flat side of the 9D-1829 Clip (70) to the engine firewall.

      Tighten the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

   Show/hide table
   
   

   Illustration 30	g00926350
   Installing the threaded insert (A) 95 mm (3.74 inch) (B) 57.2 mm (2.25 inch)

   3. Drill a 13.5 mm (0.5 inch) hole in the back of the engine firewall and install the 224-6208 Threaded Insert (56). See Illustration 30 for locating dimensions.

      Use a 9F-1829 Clip (70), a 8T-4121 Hard Washer (14), and a 8T-4195 Bolt (65) to secure the hose assemblies.

      Note: Secure the end of the hose guard that is provided on the hose assembly inside the 9D-1829 Clip (70). Install the flat side of the 9D-1829 Clip (70) to the engine firewall.

   Show/hide table
   
   

   Illustration 31	g00927871
   Installation details for 252, 262, 277, and 287 machines (A) 50° ± 3° (B) 75 mm (3 inch) (14) 8T-4121 Hard Washer (65) 8T-4195 Bolt (70) 9D-1829 Clip (77) 186-6190 Refrigerant Accumulator (82) 219-4349 Bracket

   Show/hide table
   
   

   Illustration 32	g00931539
   Installation details for 236 machines (A) 34° ± 3° (B) 95 mm (3.7 inch) (14) 8T-4121 Hard Washer (65) 8T-4195 Bolt (70) 9D-1829 Clip (77) 186-6190 Refrigerant Accumulator (82) 219-4349 Bracket

   Show/hide table
   
   

   Illustration 33	g00927872
   Installation details of hose connection to the accumulator for all machines (C) 22° ± 3° (D) 3° ± 3° (77) 186-6190 Refrigerant Accumulator (78) 219-4341 Hose As (79) 219-4342 Hose As

   Show/hide table
   
   

   Illustration 34	g00931627
   Routing the air conditioner hoses on the right side of the hydraulic tank (L) Hydraulic Tank (77) 186-6190 Refrigerant Accumulator (79) 219-4342 Hose As (80) 219-4343 Hose As (87) 220-8155 Condenser Coil As

   4. For additional mounting details, see Illustration 31, Illustration 32, Illustration 33, and Illustration 34.

6. Install the 219-4344 Hose As (81) between the compressor and the condenser. See Illustration 26.

   1. Connect the end of hose assembly (81) with the straight stem to the outlet for the compressor. The outlet is the smaller port on the left side of the compressor. Use a 9X-7381 O-Ring Seal (72) for this connection.

      Tighten the coupling to a torque of 27 ± 4 N·m (20 ± 3 lb ft).

   2. Route the hose assembly per Illustration 26.

   3. Connect the end of hose assembly (81) with the 90° stem to the inlet for the condenser. The inlet is the top connection on the right side of the condenser. Use a 9X-7381 O-Ring Seal (72) for this connection.

      Tighten the coupling to a torque of 27 ± 4 N·m (20 ± 3 lb ft).

7. Install the 219-4341 Hose As (78) between the compressor and the accumulator. See Illustration 26.

   1. Connect the end of hose assembly (78) with the 45° stem to the inlet for the compressor. The inlet is the larger port on the right side of the compressor. Use a 9X-7382 O-Ring Seal (73) for this connection.

      Tighten the coupling to a torque of 40 ± 4 N·m (30 ± 3 lb ft).

   2. Route the hose assembly per Illustration 26.

   3. Connect the end of hose assembly (78) with the 180° stem to the connector on the bottom of the accumulator. Use a 9X-7383 O-Ring Seal (74) for this connection.

      Tighten the coupling to a torque of 45 ± 5 N·m (33 ± 4 lb ft).

Show/hide table



Illustration 35	g00931535
Installation details of the hose connections to the condenser for 252, 262, 277, and 287 machines (E) 20° ± 3° (F) 10° ± 3° (80) 219-4343 Hose As (81) 219-4344 Hose As (87) 220-8155 Coil

Show/hide table



Illustration 36	g00931540
Installation details of the hose connections to the condenser for 236 machines (E) 46° ± 3° (F) 6° ± 3° (80) 219-4343 Hose As (81) 219-4344 Hose As (87) 220-8155 Coil

Show/hide table



Illustration 37	g00931538
Installation details of hose connections to the compressor for all machines (G) 66° ± 3° (78) 219-4341 Hose As (81) 219-4344 Hose As

8. For additional details for installing the hoses, see Illustration 35, Illustration 36, and Illustration 37.

Show/hide table



Illustration 38	g00928046
Installation details for securing the hose for 252, 262, 277, and 287 machines (3) 3S-2093 Cable Strap (5) 4S-1962 Clip (14) 8T-4121 Hard Washer (58) 2W-1745 Spacer (60) 5N-8359 Flexible Conduit (64) 8T-4178 Bolt (65) 8T-4195 Bolt

Show/hide table



Illustration 39	g00931412
Installation details for securing the hoses for 236 machines (3) 3S-2093 Cable Strap (5) 4S-1962 Clip (14) 8T-4121 Hard Washer (58) 2W-1745 Spacer (60) 5N-8359 Flexible Conduit (64) 8T-4178 Bolt (65) 8T-4195 Bolt

9. Secure hose assembly (78) at Location (J) and at Location (K). See Illustration 38 and Illustration 39.

   1. At Location (K), use a 4S-1962 Clip (5) to secure the hose. Use the existing 8T-4195 Bolt , and the existing 8T-4121 Hard Washer to secure the hose.

      Note: Tighten both of the 8T-4195 Bolts that are used to secure the accumulator inside the clips. Tighten the bolts to a torque of 55 ± 10 N·m (401 ± 7 lb ft).

   2. At Location (J), use a 4S-1962 Clip (5), a 2W-1745 Spacer (58), a 8T-4195 Bolt (65), and a 8T-4121 Hard Washer (14) to secure the hose.

      Tighten the bolt to a torque of 55 ± 10 N·m (401 ± 7 lb ft).

      Note: For 236 machines, use the 4W-7627 Spacer (99) and the 8T-5005 Bolt (68) instead of spacer (58) and bolt (65) .

10. At Location (L), install the 2W-1745 Spacer (58) in order to move the two hydraulic oil cooler lines away from the firewall. See Illustration 38, and Illustration 39.

    Use a 8T-4178 Bolt (64) and a 8T-4121 Hard Washer (14) to install the spacer.

    Tighten the bolt to a torque of 55 ± 10 N·m (401 ± 7 lb ft).

11. Also, install a 35 cm (14 inch) length of 5N-8359 Flexible Conduit (60) on each hydraulic oil cooler line. Secure the two lengths of flexible conduit to the hydraulic oil cooler lines with 3S-2093 Cable Straps (3) .

Installing the Heater Lines

Illustration 40	g00920181
(E) Heater Inlet (F) Heater Outlet (G) Radiator Inlet (H) Engine Block Outlet

The heater lines are installed between the following components. See Illustration 40.

• The engine block outlet (H) and the heater inlet (E) .

• The heater outlet (F) and the radiator inlet (G)

1. Cut two lengths of the 136-1953 Hose (96) per Table 6.
   Show/hide table

   Table 6

   Machine	Heater Outlet Hose	Heater Inlet Hose
   236	2260 mm (89 inch)	2160 mm (85 inch)
   252	2260 mm (89 inch)	2260 mm (89 inch)
   262	2260 mm (89 inch)	2260 mm (89 inch)
   277	2260 mm (89 inch)	2260 mm (89 inch)
   287	2260 mm (89 inch)	2260 mm (89 inch)

Show/hide table



Illustration 41	g00926148
(5) 4S-1962 Clip (14) 8T-4121 Hard Washer (15) 8T-4133 Nut (16) 8T-4136 Bolt (62) 6D-1641 Clip (90) 1L-2279 Elbow (91) 5K-6875 Adapter (92) 8F-8151 Shutoff Valve (93) 8T-0154 Hose Clamp (95) 004-6810 Elbow (96) 136-1953 Hose (97) 183-7120 Hose Guard (98) 219-4328 Elbow

Show/hide table



Illustration 42	g00932249
View of heater inlet hose (E) and heater outlet hose (F) Orientation of hose mountings at Location (G) and at Location (J) (A) 20° ± 5° (B) 30° ± 5°

2. Install the specified lengths of hose on the heater inlet (E) and the heater outlet (F). See Illustration 41.

   Use two 8T-0154 Hose Clamps (93) to install the hoses.

   Orient the hose clamps per Illustration 42. Tighten the hose clamps to a torque of 6 ± 1.0 N·m (4.4 ± 0.7 lb ft).

   Note: Pull the hoses tightly between the heater connections and Location (J) .

3. Install one 183-7120 Hose Guard (97) on each length of hose. Position each hose guard on the section of the hose between the rear cab wall and the engine firewall.

4. Route both hoses up the rear wall of the cab and then route both hoses into the engine compartment.

   Secure the hoses to the mounting stud at Location (G) and at Location (J) on the back wall of the cab. See Illustration 41.

   Use a 6D-1641 Clip (62), a 8T-4121 Hard Washer (14), and a 8T-4133 Nut (15) at each location.

   Tighten each nut to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

Show/hide table



Illustration 43	g00921563
Orientation of mounting clip at Location (K) (F) 75° ± 5°

5. At Location (K), secure the hoses to the threaded boss that is provided on the back of the engine firewall. See Illustration 43.

   Use a 6D-1641 Clip (62), a 8T-4121 Hard Washer (14), and a 8T-4136 Bolt (16) at this location.

   Tighten the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

Note: Pull the hoses tightly between Location (J) and Location (K) with the cab in the raised position. See Illustration 44.

Show/hide table



Illustration 44	g00926152
Pull hoses tightly between Location (J) and Location (K) with the cab in the raised position. (97) 183-7120 Hose Guard

6. Remove the plug in the radiator housing for installation of the heater outlet hose.

7. Assemble the 1L-2279 Elbow (90) and the 004-6810 Elbow (95) for the hose connection for the radiator inlet. See Illustration 41.

   Install this assembly in the radiator inlet.

   Tighten this assembly to a torque of 25 ± 6 N·m (18 ± 4 lb ft).

   Note: Use thread sealant in the assembly of the components and in the installation of this assembly.

Show/hide table



Illustration 45	g00921566
Orientation of hose connection at radiator inlet (G) (D) 45° ± 5° (E) 90° ± 5°

8. Route the heater outlet hose to the radiator inlet.

   Note: Route the heater outlet hose between the firewall and the hydraulic oil cooler lines.

9. Install the heater outlet hose to the 004-6810 Elbow (95) at the radiator inlet. See Illustration 45.

   Use a 8T-0154 Hose Clamp (93) to secure the hose.

   Orient the hose clamp, as shown. Tighten the hose clamp to a torque of 6 ± 1.0 N·m (4.4 ± 0.7 lb ft).

10. Remove the plug in the engine block for installation of the heater inlet hose.

11. Assemble the 8F-8151 Shutoff Valve (92), the 5K-6875 Adapter (91), and the 219-4328 Elbow (98) for the hose connection to the engine block. See Illustration 41.

    Install this assembly in the engine block.

    Tighten this assembly to a torque of 25 ± 6 N·m (18 ± 4 lb ft).

    Note: Use thread sealant in the assembly of these components and in the installation of this assembly.

Show/hide table



Illustration 46	g00921565
Orientation of hose connection at engine block outlet (H) (C) 150° ± 5°

12. Route the heater inlet hose to the engine block outlet. Install the hose to the 8F-8151 Shutoff Valve (92) with a 8T-0154 Hose Clamp (93). See Illustration 46.

    Orient the hose clamp, as shown. Tighten the hose clamp to a torque of 6 ± 1.0 N·m (4.4 ± 0.7 lb ft).

    Note: Make sure that the shutoff valve, the hose clamp, and the elbows do not contact the coolant hose. Also, make sure that these components are at least 10 mm (0.4 inch) from the radiator fan guard when the radiator is lowered.

13. For 262, 277, and 287 machines, install a 4S-1962 Clip (5) at Location (L). See Illustration 41.

    Note: The clip is installed to the existing 142-9102 Bracket , which is a part of the Radiator and Oil Cooler Mounting Gp.

    Use two 8T-4121 Hard Washers (14), a 8T-4133 Nut (15), and a 8T-4136 Bolt (16) at this location.

    Tighten the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).

Show/hide table



Illustration 47	g00926155
Install the edging around the opening in the firewall. (94) 9X-2092 Edge Strip

14. Install the 9X-2092 Edge Strip (94) in order to protect the hoses from wear. See Illustration 47.

Installing the Belt Guard

Show/hide table



Illustration 48	g00937947
(11) 7X-0579 Hard Washer (19) 8T-4200 Bolt (21) 8T-4224 Hard Washer (26) 9X-2045 Screw (28) 101-2867 Hard Washer (48) 227-5918 Belt Guard (49) 219-4392 Bracket

1. Install the 219-4392 Bracket (49) on top of the engine block. See Illustration 48.

   Use two 8T-4200 Bolts (19) and two 8T-4224 Hard Washers (21) to install the bracket.

   Tighten the bolts to a torque of 15 ± 3 N·m (11 ± 2 lb ft).

2. Install the 227-5918 Belt Guard (48) .

   1. Place the 227-5918 Belt Guard (48) in position.

   2. Install a 9X-2045 Screw (26) with a 101-2867 Hard Washer (28) in the mounting hole in the top of the belt guard. Then, install two 9X-2045 Screws (26) with 101-2867 Hard Washers (28) in the mounting holes in the front of the belt guard.

   3. Install two 8T-4200 Bolts (19) with 7X-0579 Hard Washers (11) in the mounting holes in the bottom of the belt guard.

   4. Tighten the two bolts to a torque of 15 ± 3 N·m (11 ± 2 lb ft).

   5. Then, tighten the three screws to a torque of 6 ± 1 N·m (4 ± 0.7 lb ft).

Installing the Electrical Harnesses

Show/hide table



Illustration 49	g00932246
The electrical harnesses (51) 220-5527 Harness (HVAC Cab) (52) 220-5528 Harness (HVAC Platform)

1. Install the 220-5528 Harness (HVAC Platform) (52) and the 220-5527 Harness (HVAC Cab) (51). See Table 7 and Table 8.
   Show/hide table

   Table 7

   220-5528 Harness (HVAC Platform) (52)
   Harness Connector	Circuit	Connection
   (AC-B7)	-	Connect to Connector AA-C1 on Harness (51).
   (AC-C1)	AC Condenser Fan	Connect to the fan connector on the condenser.
   (AC-C2)	AC Condenser Fan	Connect to the fan connector on the condenser.
   (AC-T6)	AC Compressor	Connect to the bullet connector on the compressor. Secure the wiring to the clip that is provided on the rear of the compressor in order to prevent accidental grounding.
   (AC-C5)	Pressure Switch	Connect to the pressure switch on the compressor. Secure this harness connection to the clip that is provided on the rear of the compressor.
   (AC-T1)	AC Power (Battery +)	Connect to the circuit breaker terminal on the inside of the left tower. See View A of Illustration 50. (1)

   Show/hide table

   ( 1 )

   Replace the existing 60 Amp circuit breaker with the 216-4970 Circuit Breaker (120 Amp) (9). Use the two 5L-4507 Screws (106) and the two 4B-4274 Washers (105) to install the circuit breaker.

   Show/hide table

   Table 8

   220-5527 Harness (HVAC Cab) (51)
   Harness Connector	Circuit	Connection
   (AA-C1)	-	Connect to Connector AC-B7 on Harness (52).
   (AA-T1)	AC Ground	Connect to the Grounding Stud on the back of the cab. See Illustration 51.
   (AA-C2)	AC Fan Motor	Connect to the connector for the fan motor under the cab.

Show/hide table



Illustration 50	g00942986
The circuit breaker panel on the inside of the left tower (9) 216-4970 Circuit Breaker (120 Amp) (105) 4B-4274 Washer (106) 5L-4507 Screw

Show/hide table



Illustration 51	g00933471
The grounding stud on the back of cab

2. Route the harnesses with existing harness wiring. Use 3S-2093 Cable Straps (3) to secure the new harnesses to existing harnesses.

   Note: Do not route the 220-5527 Harness (HVAC Cab) (51) through the opening in the firewall. Route the harness under the torque tube.

Charging the Air Conditioner System

Use the procedure "Complete Charge of the System from a Refrigerant Tank with a Scale" to charge the air conditioner system. This procedure is part of the Testing and Adjusting, SENR5664, "Air Conditioning and Heating R-134a for All Caterpillar Machines"". This procedure can be obtained through the normal literature distribution system. This procedure can also be found on the Caterpillar Service Information System (SIS).

Note: Charge the system with 0.68 kg (1.5 lb) of R-134a refrigerant.

Show/hide table



Illustration 52	g00940523
(3) 3S-2093 Cable Strap (102) 223-9636 Instruction Plate

1. Install the 223-9636 Instruction Plate (102) on the suction inlet port of the compressor. Use a 3S-2093 Cable Strap (3) to tie the instruction plate on the compressor. See Illustration 52.

Checking the Air Conditioner and Heater Installation

Show/hide table



Illustration 53	g00927471
(100) 162-5233 Film (Work Tool Control)

1. Install the 162-5233 Film (Work Tool Control) (100) on the left side of the air conditioner and heater. See Illustration 53.

Show/hide table



Illustration 54	g00926157
Position for installing fuse (29) for the air conditioner and heater

2. Install the 113-8492 Fuse (20 Amp) (29) in the indicated position in the fuse box. See Illustration 54.

3. Refill the cooling system.

   Refer to "Coolant Recommendations" and refer to "Cooling System Specifications" in the Operation and Maintenance Manual for your machine.

4. Start the engine. Run the engine without the radiator cap until the thermostat opens and the coolant level stabilizes. Maintain the coolant level in the sight gauge. The sight gauge is located on the right side of the radiator.

5. Stop the engine. Install the radiator cap.

6. Check the hoses and the fittings for leaks.

7. Start the engine.

8. Check the air conditioner and heater unit for proper operation.
   Show/hide table
   
   

   Illustration 55	g00926159
   Temperature control knob

   1. The temperature control knob adjusts the output temperature. See Illustration 55.
      • Turn the temperature control knob clockwise in order to increase the temperature.

      • Turn the temperature control knob counterclockwise in order to decrease the temperature.

   Show/hide table
   
   

   Illustration 56	g00927465

   2. A/C switch
      • Press the front portion of the rocker switch in order to turn on the air conditioner.

      • Press the rear portion of the rocker switch in order to turn off the air conditioner.

   Show/hide table
   
   

   Illustration 57	g00926161
   Fan speed switch

   3. The fan speed switch controls the two-speed blower fan motor. See Illustration 57.
      • Press the rear portion of the rocker switch for low fan speed.

      • Press the front portion of the rocker switch for high fan speed.

      • Return the switch to the neutral position in order to turn off the fan.

   Show/hide table
   
   

   Illustration 58	g00926163
   Adjustable louver

   4. The louver directs the flow of air, as needed. See Illustration 58.
      • The louver can be rotated for 360°.

      • The louver can be adjusted from a closed position to an open position.

   Show/hide table
   
   

   Illustration 59	g00926164
   Recirculating filter

   5. To gain access to the air filter, loosen the two thumb screws and remove the grill panel. See Illustration 59.