Gear Pump (Hoist) - Install
安装步骤
- 检查并清洁所有零件。 如果任何零件磨损或损坏,则应使用 Caterpillar 新件进行更换。
- 更换齿轮泵 (13) 上的 O 形密封圈(图中未显示)。
Show/hide table
图 1 | g00809334 |
- 将适当的尼龙吊索连接到齿轮泵 (13) 和适当的举倾机构上。 升起齿轮泵进入机器上的位置。 齿轮泵的重量为 43.5 kg (96 lb)。
- 将齿轮泵轴 (13) 上的花键与泵驱动壳体上齿轮的花键对准。 将齿轮泵滑入位置,然后安装两只螺栓 (18) 和两只垫圈 (19) 以便将齿轮泵固定到机器上。
- 将软管 (8) 连接到齿轮泵。 安装四颗螺栓 (5) 、四只垫圈 (6) 和两个半环卡箍 (7) 以便将软管固定到齿轮泵上。 安装两颗螺栓 (1) 、两只硬垫圈 (2) 和隔套 (3) 以便将安装支架和电气接头 (4) 固定到机器上。
Show/hide table
图 2 | g00809225 |
- 将软管 (17) 连接到齿轮泵 (13) 上。 安装三颗螺栓 (14) 、三只垫圈 (15) 和两个半环卡箍 (16) 。 将软管绑带连接到泵上。 将软管卡箍 (12) 安装到半环卡箍上。 安装螺栓 (9) 、垫圈 (10) 和隔套 (11) 以便将软管卡箍和半环卡箍固定到机器上。
Show/hide table
图 3 | g00809235 |
End By:
- 安装驾驶室。 请参阅 拆解和组装, "驾驶室 - 安装"。
- 检查液压油油位。 请参阅 操作和保养手册, "举倾机构、转向和制动系统油 - 更换"。
Caterpillar Information System:
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Using Caterpillar Monitoring System to Determine Diagnostic Codes
446B Backhoe Loader Transmission (Autoshift) Transmission and Torque Converter - Test
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Using Vital Information Management System to Determine Diagnostic Codes
793B Off-Highway Truck Power Train Visual Inspection (Power Train)
2001/07/30 New Assembly Instructions for Rod Seals on Hydraulic Cylinders are Available {7562}
769D Off-Highway Truck/Tractor and 771D Quarry Truck Engine Oil and Filter - Change
TL2 Series In-Line Rippers Shear Bolt - Replace
793B Off-Highway Truck Power Train Specifications (Power Train)
TK1051 Track Feller Buncher Machine Systems Main Control Valve - Remove
37-MT, 41-MT, and 42-MT Series Starting Motors General Information
446B Backhoe Loader Transmission (Autoshift) Pressure Taps
2008/09/08 Procedure for the Repair of the Front Axle Assembly {3278}
CP-663E, CS-663E and CS-683E Vibratory Compactors Machine Systems Axle Guard - Remove and Install
740 and 740 EJECTOR Articulated Trucks Power Train Transmission Shift Points - Test
TH210 and TH215 Telehandlers Towing the Machine
784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 797 and 797B Off-Highway Trucks VIMS ™ Electrical Component and Connector Locations
M313C, M315C, M316C, M318C, M318C MH, M322C and M322C MH Excavators Electronic System Electronic Control Module (ECM) - Replace
M313C, M315C, M316C, M318C, M318C MH, M322C and M322C MH Excavators Electronic System Glossary of Terms
PM-465 Cold Planer Conveyor Controls
2001/08/06 The Enclosure for the Brake Linkage Has Been Improved {4250}
TH210 and TH215 Telehandlers Engine Starting
Product Link 151/201 Wiring Harness (Open Circuit) - Test
37-MT, 41-MT, and 42-MT Series Starting Motors Pinion Clearance - Adjust
2001/07/09 The Bolt that Attaches the Gear Shroud Assembly to the PTO case Has Been Lengthened {3107}