Measuring Arm - Disassemble
Disassembly Procedure
Start By:
- Remove the measuring arm from the harvester head. Refer to Disassembly and Assembly, "Measuring Arm - Remove".
- Cover (6) and cover screws (5) were removed when the measuring arm was removed from the harvester head.
Show/hide table
Illustration 1 | g00765708 |
(1) Grease fitting. (2) Locknut. (3) Washer. (4) Pin. (5) Screw. (6) Cap. (7) Retaining ring. (8) Measuring roller assembly. (9) Bearing. (10) Cap. (11) Screw. (12) Socket head bolt. |
- Remove locknut (2) and washer (3) from bolt (4) .
- Remove bolt (4) .
- Remove three screws (11) in the center of cap (10) .
- Remove six bolts (12) that attach cap (10) to measuring roller (8). Remove cap (10) .
- Remove snap ring (7) from the stub shaft of the measuring arm.
- Remove bearing (9) and measuring roller (8) .
- Remove three screws (15) that attach encoder (16) to the measuring arm. Remove encoder (16) .
Show/hide table
Illustration 2 | g00765757 |
- Remove carrier (18) and washer (17) from encoder (16) .
- Remove grease fitting (1) from the measuring arm.
Note: Clean all parts. Check the condition of all seals and of all components. Replace all parts that are worn or damaged.
Caterpillar Information System:
AP-1000B and BG-260C Asphalt Pavers Indicators
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System General Information (Hydraulic System)
C-15 and C-16 Industrial Engines Alternator and Regulator
2001/04/02 New Recommendations for Selecting the Oil Viscosity for the Differentials and Final Drives {3258, 4011, 4051, 7581}
725, 730 and 730 EJECTOR Articulated Trucks Power Train Relief Valve (Transmission Hydraulic Control) - Remove and Install
2001/01/29 Correction to the Special Instruction for the Procedure to Retrofit the Scarifier {6162, 6165}
2001/01/08 Improved Transmission Direction Switch Now Used {7332}
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm - Remove
RM-250C Reclaimer Mixer Machine Systems Air Compressor Governor - Test and Adjust
RM-250C Reclaimer Mixer Machine Systems Rotor Drive Chain Tension - Check and Adjust
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Feed Roller - Assemble
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Feed Roller - Disassemble
RM-250C Reclaimer Mixer Machine Systems Shifter (Rotor Axle) - Test
725, 730 and 730 EJECTOR Articulated Trucks Power Train Bypass Valve - Remove and Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm - Assemble
725 and 730 Articulated Trucks Power Train Differential - Test
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm - Install
725, 730 and 730 EJECTOR Articulated Trucks Power Train Pump Drive - Assemble
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension Height (Front) - Check and Adjust
236, 246, 248, 252 and 262 Skid Steer Loaders Engine Supplement Air Cleaner - Remove and Install
725, 730 and 730 EJECTOR Articulated Trucks Power Train Solenoid Valve (Transmission Clutch Latching) - Remove and Install
2001/01/15 A Special Instruction, REHS0973-01 , "Installation of New Dual Signal Network to Separate Hydraulic Signal of Loader and Backhoe" is Available {5057}
730 EJECTOR and 740 EJECTOR Articulated Trucks Front Suspension Cylinder - Remove
TH103 Telehandler Hydraulic System Pilot Hydraulic System