Feed Roller - Disassemble
Disassembly Procedure
Show/hide table
 |
The harvester head frame may tip over when it is in the vertical position. Personal injury or death may result if this occurs. Secure the frame to the yoke with a chain or similar restraint prior to working on the harvester head. |
 |
Note: Chains should be replaced one at a time in order to maintain the proper orientation of the chains to the feed rollers.
- Ensure that the harvester head frame is in the VERTICAL position. Fully open the feed roller arms. Secure the frame of the harvester head to the yoke with a suitable chain. Refer to Disassembly and Assembly, "Preparation for Disassembly" for detailed instructions.
- Remove five screws (2). Remove ring (3) .
Show/hide table
 | |
| Illustration 1 | g00450632 |
(1) Chain. (2) Screw. (3) Ring. (4) Feed roller. | |
- If the chain is not broken, cut the chain. Remove the pieces of the chain from feed roller (4). The chain is held onto feed roller (4) by having a link of the chain placed into a slot on the front and back of feed roller (4) .
Show/hide table
 | |
| Illustration 2 | g00450663 |
(1) Chain. (4) Feed roller. (5) Slot. | |
Caterpillar Information System:
RM-250C Reclaimer Mixer Machine Systems Rotor Clutch Pressure (Power Take-Off Clutch) - Test and Adjust
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Feed Roller - Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Feed Roller - Remove
RM-250C Reclaimer Mixer Machine Systems Wheel Alignment - Check and Adjust
RM-250C Reclaimer Mixer Machine Systems Machine System Troubleshooting
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm Cylinder - Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm Cylinder - Remove
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System System Schematic
725, 730 and 730 EJECTOR Articulated Trucks Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
725 and 730 Articulated Trucks Power Train Interaxle Differential - Test
2001/11/05 A New Optional Two-Piece Service Replacement Piston Is Available {1214}
725, 730 and 730 EJECTOR Articulated Trucks Power Train Relief Valve (Torque Converter Outlet) - Remove and Install
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Feed Roller - Assemble
RM-250C Reclaimer Mixer Machine Systems Rotor Drive Chain Tension - Check and Adjust
RM-250C Reclaimer Mixer Machine Systems Air Compressor Governor - Test and Adjust
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm - Remove
2001/01/08 Improved Transmission Direction Switch Now Used {7332}
2001/01/29 Correction to the Special Instruction for the Procedure to Retrofit the Scarifier {6162, 6165}
725, 730 and 730 EJECTOR Articulated Trucks Power Train Relief Valve (Transmission Hydraulic Control) - Remove and Install
2001/04/02 New Recommendations for Selecting the Oil Viscosity for the Differentials and Final Drives {3258, 4011, 4051, 7581}
C-15 and C-16 Industrial Engines Alternator and Regulator
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System General Information (Hydraulic System)
AP-1000B and BG-260C Asphalt Pavers Indicators
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Measuring Arm - Disassemble