Tilt Lever (Front) and Tilt Link (Front) - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-0960     | Molybdenum Grease     | 1     |
- Before installation, lubricate the pin bores with Tooling (A) .
- Lower the temperature of bearings (11), (12), and (13). Use insulated gloves to handle the bearings.
Show/hide table
Illustration 1 | g00281645 |
- Install bearing (11) to a depth of 8.5 ± 1.0 mm (0.33 ± 0.04 inch).
- Install bearing (12) to a depth of 11.0 ± 1.0 mm (0.43 ± 0.04 inch).
- Install bearing (13) to a depth of 8.5 ± 1.0 mm (0.33 ± 0.04 inch).
- Fasten a suitable lifting device to tilt lever (5) and to tilt link (4) .
Show/hide table
Illustration 2 | g00281644 |
- Install tilt lever (5) and tilt link (4) as a unit. The total weight of the tilt lever and of the tilt link is approximately 109 kg (240 lb). Install pin assembly (7) and bolt (10) .
- Install pin assembly (9) and bolt (8) .
- Use a suitable lifting device to support tilt cylinder (1), as shown. Raise the tilt cylinder into position.
Show/hide table
Illustration 3 | g00281643 |
- Install pin assembly (3) and bolt (2) .
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
938G Wheel Loader and IT38G Integrated Toolcarrier Machine Systems Tilt Lever (Front) and Tilt Link (Front) - Remove
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Check Valve (Parking Brake Release)
CB-214D, CB-224D and CB-225D Vibratory Compactors Compaction and Rolling Procedure
TH62, TH63, TH82 and TH83 Telehandlers Tire Shipping Pressure
776D, 777D and 777D HAA Off-Highway Truck/Tractors Hydraulic System Hydraulic System
24H Motor Grader Articulation Cylinder Bearings - Lubricate
JF Series Starting Motor Field Winding - Test
2000/07/17 New Crossover Relief Valves Are Used in the Hydrostatic Pump Group {3203}
TH103 Telehandler Fuel System Primary Filter - Replace
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Manifold (Tractor)
TH103 Telehandler Stopping the Machine
784B, 784C, 785B, 785C, 785C HAA, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors Variable Speed Fan Drive Fan Drive - Assemble
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Manifold (Trailer)
938G Wheel Loader and IT38G Integrated Toolcarrier Machine Systems Tilt Lever - Remove
JF Series Starting Motor Starting Motor Does Not Turn or Turns Slowly
Alternator - Delco 27SI Brush Length - Check
938G Wheel Loader and IT38G Integrated Toolcarrier Machine Systems Tilt Lever - Install
JF Series Starting Motor Starting Motor - Disassemble
IT28G Integrated Toolcarrier and 928G Wheel Loader Brake and Fan Drive System Rocker Switch (Transmission Neutralizer Override Control)
3054B Engine for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
550, 570 and 580 Wheel Harvesters Steering Cylinder Mounting Bolts - Tighten
776D Tractors and 777D and 777D HAA Off-Highway Truck Steering System Gear Pump (Steering)
Alternator - Delco 21SI Field Winding - Test
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Pressure Switch (Secondary Brake and Parking Brake)