Transmission Neutralizer Pressure Switch - Adjust
Show/hide table
| |
| Illustration 1 | g00712247 |
Transmission neutralizer pressure switch (1) is located behind the floormat in the area that is fastened to the side trim. The transmission neutralizer pressure switch is used in conjunction with the transmission neutralizer control (switch) on the instrument panel to disengage the transmission when pressure is applied to the brake pedal.
The brake pedal pressure that is needed to disengage the transmission can be adjusted in order to suit the operating conditions. Use the following procedure in order to adjust the transmission neutralizer pressure switch:
- Remove fasteners (2) that secure the floormat to the side trim. Pull back the floormat in order to access the transmission neutralizer pressure switch.
Show/hide table
Illustration 2 g00714181 - Remove rubber boot (3) from transmission neutralizer pressure switch (1) in order to expose screw (4).
- Turn the screw in a counterclockwise direction if you wish to apply a lighter pressure to the brake pedal in order to disengage the transmission. Turn the screw in a clockwise direction if you wish to apply a firmer pressure to the brake pedal in order to disengage the transmission.
For more information on the transmission neutralizer, refer to Operation and Maintenance Manual, "Transmission Neutralizer Control" and Operation and Maintenance Manual, "Service Brake Control".
Caterpillar Information System:
2000/06/19 Precleaner Assemblies Are Now Serviceable {1051, 1055}
2000/05/29 The Required Torque has been Increased for the Piston Retaining Nut in the Tilt Cylinder {5104}
2000/05/29 The Required Torque has been Increased for the Piston Retaining Nut in the Lift Cylinder {5102}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Service Brakes - Remove and Install
2000/06/19 Correction to Service Magazine, 9EP3441, 31 October 1999 , "New Thrust Washer Improves Service Life of Differential Group" {3258}
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Accumulator (Refrigerant) Remove and Install
TH62, TH63, TH82 and TH83 Telehandlers Transmission Breather - Clean
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive - Remove
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors CID 0274 FMI 13 Atmospheric Pressure calibration required
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 04 Turbo Outlet Pressure short to ground
797 Off-Highway Truck Fan Drive Hydraulic System Suction Fan
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Oil Cooler (Brake) - Install
IT28G Integrated Toolcarrier and 928G Wheel Loader Steering System Pressure Switch (Primary Steering Oil and Secondary Steering Oil)
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Refrigerant Condenser - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Backup Alarm - Test
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Pump Drive - Remove
D350E Series II and D400E Series II Articulated Trucks Brakes, Indicators and Gauges - Test
TH62, TH63, TH82, TH83 and TH103 Telehandlers Engine Supplement Transmission Oil Cooler - Remove
3408E and 3412E Engines for Caterpillar Built Machines Throttle Switch Circuit - Test
CS-531D, CP-533D and CS-533D Vibratory Compactors Vibratory System Vibratory Frequency - Test and Adjust
2000/06/19 Special Instructions, REHS0611-01 (SI1128-01), "Installation of Axle Cooling" is Available {1365}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Pump Drive - Install