AP-1050B and BG-245C Asphalt Pavers Caterpillar


Safety Messages

Usage:

BG-245C 4XN
There are several specific safety messages on your machine. The exact location of the hazard and description of the hazard are reviewed in this section. Take the time in order to become familiar with these safety messages.

You must be able to read all safety messages. Clean the safety messages in order to read the words. Clean the safety messages in order to see the pictures. Replace the safety messages in order to read the words. Replace the safety messages in order to see the pictures. In order to clean the safety messages, use a cloth, water and soap. Do not use solvent, gasoline, etc.

You must replace a safety message that is damaged or missing. You must replace a safety message that cannot be read. If a safety message is on a part that has been replaced, a new safety message must be installed on the replacement part. See your dealer for new safety messages.

Do Not Operate




Illustration 2g00738919

This safety message is located on the right access door for the engine on top of the machine.




Illustration 3g00738544

------ WARNING! ------

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Caterpillar dealer for replacement manuals. Proper care is your responsibility.

----------------------



Illustration 4g00739145

This safety message is located on the operator station.




Illustration 5g00738764

------ WARNING! ------

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Caterpillar dealer for replacement manuals. Proper care is your responsibility.

----------------------

Mounting the Machine




Illustration 6g00738588

This safety message is located on each side of the machine on the tow arm.




Illustration 7g00738596

------ WARNING! ------

Mounting the machine from the side could cause personal injury. Use the ladder provided on the screed at the rear of the machine to mount the machine.

----------------------

No Open Fire




Illustration 8g00738716

This safety message is located on the rear of the machine.




Illustration 9g00738728

------ WARNING! ------

No open fire within15 m (50 ft) of the screed area while lighting the screed burners. Personal injury could result from the open fire.

----------------------

Secure Hopper Wings




Illustration 10g00742574

This safety message is located on each side of the machine at the rear of the hopper wings.




Illustration 11g00738752

------ WARNING! ------

Working underneath unsecured, raised hoppers could cause personal injury. Use eyes in the hoppers to secure the hoppers together in the fully raised position while working underneath the hoppers.

----------------------

Improper Connections for Jump Start Cables




Illustration 12g00742587

This safety message is located under the access panel on the right side of the machine next to the battery disconnect switch.




Illustration 13g00739254

------ WARNING! ------

IMPROPER JUMPER CABLE CONNECTIONS CAN CAUSE EXPLOSION RESULTING IN PERSONAL INJURY.

BATTERIES MAY BE LOCATED IN SEPARATE COMPARTMENTS. WHEN USING JUMPER CABLES, ALWAYS CONNECT POSITIVE (+) CABLE TO POSITIVE (+) TERMINAL OF BATTERY CONNECTED TO STARTER SOLENOID AND NEGATIVE (-) CABLE FROM EXTERNAL SOURCE TO STARTER NEGATIVE (-) TERMINAL (IF MACHINE NOT EQUIPPED WITH STARTER NEGATIVE TERMINAL, CONNECT TO ENGINE BLOCK.) FOLLOW PROCEDURE IN THE OPERATION MANUAL.

----------------------

Flammable Materials




Illustration 14g00739358

This safety message is located on the air cleaner housing.




Illustration 15g00739212

------ WARNING! ------

Do not use flammable materials in or around the air cleaner. Flammable materials used in or around the air cleaner can explode and cause personal injury.

----------------------

Caterpillar Information System:

C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0253 FMI 02 Personality Module mismatch
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0254 FMI 12 Electronic Control Module Error
2000/06/12 New Parts for the Controls of the Individual Clutch Modulation (ICM) are Available {3083}
3408E and 3412E Engines for Caterpillar Built Machines Engine Sensor Open/Short Circuit - Test
2000/05/22 New Sender Assembly for the Fuel Level has Improved Service Life {1273}
TH62, TH63, TH82 and TH83 Telehandlers Radiator Screen - Clean
TH62, TH63, TH82 and TH83 Telehandlers Radiator Core - Clean
CS-531D, CP-533D and CS-533D Vibratory Compactors Vibratory System General Information
2000/06/19 New Brackets are Needed When a New EMS Panel is Installed {7490}
IT28G Integrated Toolcarrier and 928G Wheel Loader Brake and Fan Drive System Brake Accumulator
TH62, TH63, TH82 and TH83 Telehandlers Quick Coupler - Lubricate
D400E Series II Ejector Truck Ejector Blade Cutting Edge - Check/Adjust
CS-531D, CP-533D and CS-533D Vibratory Compactors Vibratory System Piston Pump
IT28G Integrated Toolcarrier and 928G Wheel Loader Steering System Pressure and Flow Compensator Valve (Steering)
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Dryer (Refrigerant) - Remove and Install
3508B and 3512B Engine Supplement for 776D, 777D, and 777D HAA Tractor/Off-Highway Trucks Oil Pan - Install
Topcon® System Five Operation
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Axle Housing - Disassemble
143H and 163H Motor Graders Before Operation
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System Solenoid Valve (Blade Lift, Lower, Tip, and Tilt) - Calibrate
AP-1050B and BG-245C Asphalt Pavers Parking
2000/06/05 New Lock Valves for the Stabilizers Keep the Cylinder Head Tight {5057, 5067, 5468}
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Differential - Disassemble
143H and 163H Motor Graders Operation
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.