Regulator (Power Window) - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 1U-7575 | 六角扳手 | 1 |
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 使用螺钉起子从拉手组件 (1) 上拆下两个盖 (2)。
Show/hide table
图 3 g00704204 - 拆下两个螺栓 (3),以拆下拉手组件 (1)。
Show/hide table
图 4 g00704202 - 松开调整螺钉 (5)(未显示)以便从门把手上拆下旋钮 (4)。
Show/hide table
图 5 g00704201 - 使用螺钉起子将摇臂开关组件 (6) 从面板组件 (7) 上撬下。
Show/hide table
图 6 g00704199 - 从摇臂开关组件 (6) 的电气接头断开导线线束 (8)。
Show/hide table
图 7 g00704197 注: 标记所有的螺栓、螺钉和垫圈,以便于安装。
- 拆下两个螺栓 (11) 和硬垫圈,以从面板组件 (7) 上拆下车门挡块 (10)。
- 将两个圆头螺钉 (12) 从面板组件 (7) 上拆下。 拆下十个大圆头螺钉 (9) 和垫圈,以拆下面板组件 (7)。
Show/hide table
图 8 g00704207 - 拆下两个螺钉 (14)。 拆下四个螺栓 (13) 和硬垫圈,以将板组件 (15) 从驾驶室门上拆下。
Show/hide table
图 9 g00704208 Show/hide table图 10 g00704209 - 支撑玻璃组件。 从玻璃组件上拆下两个螺母 (16) 和垫圈。
- 将工具 (A) 安装到车门上。 将玻璃组件降下到工具 (A) 上。
Show/hide table
图 11 g00704210 - 拆下六个螺钉 (17),以将调节器组件 (18) 从驾驶室门上拆下。
Show/hide table
图 12 g00704211 - 从调节器组件 (18) 的电气接头断开导线线束 (19)。
Show/hide table
图 1 | g00704195 |
Show/hide table
图 2 | g00704206 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 1U-7575 | 六角扳手 | 1 |
注: 检查所有部件是否磨损或损坏。 如有必要,请更换部件。 利用不起毛的抹布擦拭所有部件。
- 从调节器组件 (18) 的电气接头连接导线线束 (19)。
Show/hide table
图 14 g00704210 - 使用六个螺钉 (17),以将调节器组件 (18) 安装到驾驶室门中。
Show/hide table
图 15 g00704208 - 将玻璃组件从工具 (A) 上升起。 在玻璃组件上安装两个螺母 (16) 和垫圈。 从驾驶室门上拆下工具 (A)。
Show/hide table
图 16 g00704207 - 使用四个螺栓 (13) 和硬垫圈,以将板组件 (15) 安装到驾驶室门上。 安装两个螺钉 (14)。
Show/hide table
图 17 g00704197 注: 安装之前,先将 4C-9613 硅密封胶涂抹在面板组件 (7) 的背后。
- 使用十个大圆头螺钉 (9) 和垫圈,安装面板组件 (7),如图所示。 将两个圆头螺钉 (12) 安装到面板组件 (7) 上。
- 使用两个螺栓 (11) 和硬垫圈,以在面板组件 (7) 上安装车门挡块 (10)。
Show/hide table
图 18 g00704199 - 从摇臂开关组件 (6) 的电气接头连接导线线束 (8)。
Show/hide table
图 19 g00704201 - 将摇臂开关组件 (6) 压入面板组件 (7)。
Show/hide table
图 20 g00704202 - 将旋钮 (4) 放置在门把手上,如图所示。 拧紧调整螺钉 (5)(未显示)。
Show/hide table
图 21 g00704204 - 使用两个螺栓 (3),将拉手组件 (1) 安装到车门上。
Show/hide table
图 22 g00704206 - 将两个盖 (2) 安装在拉手组件 (1) 上。
Show/hide table
图 13 | g00704211 |
Caterpillar Information System:
2000/05/01 New Asphalt Deflector Kit {6630, 6631, 6640}
24H Motor Grader Hydraulic System Oil - Change
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Accelerator Control - Remove and Install
2001/12/10 Correction to Hydraulic Schematic {5050}
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Metering Pump (Steering)
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Backlash and Bearings - Adjust
2000/05/01 Setting the Ramp Time {5645, 7220}
12H Motor Grader Engine Oil and Filter - Change
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Control Valve (Hoist) - Install
24H Motor Grader Fuses - Replace
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Control Valve (Hoist) - Assemble
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-9081</B> Generator through <B>5N-9432</B> Generator
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Hydraulic Cylinder (Steering)
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Signal and Pressure Reducing Valve (Steering) - Check
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Machine Preparation for Troubleshooting
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Visual Inspection
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Metering Pump (Steering) - Test
2000/06/12 A New Nitrogen Charging Valve for Use in Accumulators Provides Improved Service Life {4263, 4331}
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Steering Cylinder - Test
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Secondary Steering Pump - Check
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Axle Shaft - Remove - Equipped with TCS
12H Motor Grader Ether Starting Aid Cylinder - Replace
24H Motor Grader Hydraulic System Oil Filter - Replace
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0358 - FMI 03