Accelerator Control - Remove and Install
开始:
- 拆下驾驶室前盖。 请参阅拆解和组装盖, "(驾驶室前部)- 拆卸和安装"。
- 断开线束组件 (1)。
Show/hide table
图 2 g00576226 - 使用螺丝刀拆卸固定环 (2)(图中未显示)和销钉 (3)。 将踏板组件与板组件分离。
Show/hide table
图 3 g00531506 - 从踏板组件上卸下两个衬套 (4)。
- 拆下螺钉 (5)。 将旋转位置传感器 (6) 从踏板组件上拆下。
Show/hide table
图 4 g00531504 - 将护孔环 (7) 和旋转位置传感器 (6) 从板组件上拆下。
Show/hide table
图 5 g00531501 - 使用螺丝刀拆下固定环 (8) 和销钉 (9),将滚柱 (10) 从踏板组件上拆下。
- 将护盖 (11) 从踏板组件上拆下。
Show/hide table
图 1 | g00531511 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 4C-4030 | 螺纹锁固胶 | 1 |
- 将护盖 (11) 安装至踏板组件。
- 将滚柱 (10)、销钉 (9) 和挡圈 (8) 安装至踏板组件。
Show/hide table
图 7 g00531504 - 将线束组件穿过板组件定位在旋转传感器 (6) 和护孔环 (7) 上,如图所示。
Show/hide table
图 8 g00531506 - 将工具 (A) 涂覆到螺钉 (5) 的螺纹上。 使用螺钉 (5) 将旋转位置传感器 (6) 安装至踏板组件。
- 将两个衬套 (4) 安装至踏板组件。
Show/hide table
图 9 g00576226 - 使用螺丝刀,用销钉 (3) 和固定环 (2)(图中未显示)将踏板组件安装至板组件。
Show/hide table
图 10 g00531511 - 连接线束组件 (1)。
Show/hide table
图 6 | g00531501 |
结束:
- 安装驾驶室前盖。 请参阅拆解和组装, "盖(驾驶室前部)- 拆卸和安装"。
Caterpillar Information System:
2001/12/10 Correction to Hydraulic Schematic {5050}
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Metering Pump (Steering)
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Backlash and Bearings - Adjust
2000/05/01 Setting the Ramp Time {5645, 7220}
12H Motor Grader Engine Oil and Filter - Change
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Control Valve (Hoist) - Install
24H Motor Grader Fuses - Replace
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Control Valve (Hoist) - Assemble
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-9081</B> Generator through <B>5N-9432</B> Generator
140H and 160H Motor Graders Engine Oil and Filter - Change
24H Motor Grader Fuel Tank Water and Sediment - Drain
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0498 - FMI 06
24H Motor Grader Hydraulic System Oil - Change
2000/05/01 New Asphalt Deflector Kit {6630, 6631, 6640}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Regulator (Power Window) - Remove and Install
CS-431C, CP-433C and CS-433C Vibratory Compactors Auxiliary Hydraulic System Hydraulic Cylinder (Steering)
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Signal and Pressure Reducing Valve (Steering) - Check
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Machine Preparation for Troubleshooting
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Visual Inspection
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Metering Pump (Steering) - Test
2000/06/12 A New Nitrogen Charging Valve for Use in Accumulators Provides Improved Service Life {4263, 4331}
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Steering Cylinder - Test
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Secondary Steering Pump - Check
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Axle Shaft - Remove - Equipped with TCS