Air/Hydraulic Cylinder (Front Caliper) - Install
Installation Procedure
Note: Check all of the O-ring seals and the components for wear or for damage. Replace the components, if necessary. Lubricate all of the O-ring seals lightly with the lubricant that is being sealed. Clean all of the components with a cloth that is free of loose material (lint).
- Position air/hydraulic cylinder (2) on the machine. The weight of the air/hydraulic cylinder is 14 kg (30 lb). Install three bolts (5) and the hard washers.
Show/hide table
 | |
| Illustration 1 | g00698657 |
- Connect hose assembly (3) and hose assembly (4) to air/hydraulic cylinder (2) .
Show/hide table
 | |
| Illustration 2 | g00698644 |
- Connect hose assembly (1) to air/hydraulic cylinder (2) .
Show/hide table
 | |
| Illustration 3 | g00698643 |
End By: Remove the body retaining pins. Refer to Disassembly and Assembly, "Pin (Body Retaining) - Remove and Install".
Caterpillar Information System:
988G Wheel Loader Electrohydraulic System Connector Locations
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Ejector Control Valve
228 and 248 Skid Steer Loaders Machine Systems Hydrostatic System - Test and Adjust
777D HAA Off-Highway Truck Retarding
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Tilt Cylinder
2000/04/17 Pull the Injector Sleeve with a 139-0692 Sleeve Jaw {0706, 1713}
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Relief Valve (Steering Cylinder Crossover) - Test and Adjust
24H Motor Grader Cooling System Coolant (ELC) - Change
988G Wheel Loader Electrohydraulic System Machine Preparation for Troubleshooting
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System Electrical Connector - Inspect
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Selection Guide for Voltage Regulator (All Except SR4B for 3500 Engines)
10B Pavemaster Screed Maintenance Interval Schedule
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System General Information
Procedure for Salvaging Off-Highway Truck Wheel Bolt Holes or Stud Holes{4201} Procedure for Salvaging Off-Highway Truck Wheel Bolt Holes or Stud Holes{4201}
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Using Caterpillar Monitoring System to Determine Diagnostic Codes
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Rear Brake) - Remove
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Relief Valve (Ejector)
826G Landfill Compactor, 825G Soil Compactor, 824G Wheel Dozer and 980G Wheel Loader Power Train Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System Diagnostic Code List
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System Hydraulic System Troubleshooting
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Rear Brake) - Install
CS-531D, CP-533D and CS-533D Vibratory Compactors Lubricant Viscosities
2000/11/20 New Software Files for the "IQAN" Control System are Available on SIS {5705}
24H Motor Grader Cooling System Pressure Cap - Clean/Replace