Electrical Connector - Inspect
间歇性电气故障经常是由不良线路连接造成的。 检查接头时，参考下列检查项目。
- 检查接头连接情况。
- 确保 锁圈 正确锁紧。
- 确保在密封良好的接头上使用锁紧夹。
- 确保接头中心紧固。
- 确保接头触针和插孔正确对准。
- 确保 锁圈 正确锁紧。
- 检查接头上的导线。
- 确保导线笔直地连入接头后部。
- 确保所有导线正确压接在相应的接头触针上。
- 确保各接头触针正确锁定在相应接头内。 当接头触针正确锁定时，触针（导线）不能轻易地从接头体中拔出。
- 确保导线笔直地连入接头后部。
- 检查各导线的绝缘层有无缺口或磨损的痕迹。
- 检查接头上有无水气。
- 检查接头密封是否损坏或丢失。
- 检查导线孔插头是否丢失或松动。
- 检查未正确接入接头的导线。
- 如果导线以一定角接入接头，则接头和导线绝缘层之间可能无法良好的密封。
- 湿气可以通过导线绝缘层进入接头。
- 检查接头密封是否损坏或丢失。
- 检查触点是否脏污或腐蚀。
- 只能使用棉签或软刷和工业酒精清洁触针。
- 只能使用棉签或软刷和工业酒精清洁触针。
- 检查各插销和插孔。
- 使用新的触针和插孔检查各接头触针是否保持滑动配合。 如果接头在触针朝下情况下保持不动，那么新的触针应保持连接。
- 使用新的触针和插孔检查各接头触针是否保持滑动配合。 如果接头在触针朝下情况下保持不动，那么新的触针应保持连接。
Caterpillar Information System:
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Selection Guide for Voltage Regulator (All Except SR4B for 3500 Engines)
10B Pavemaster Screed Maintenance Interval Schedule
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options VR3 Voltage Regulator Connections (All Except SR4B for 3500 Engines)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options VR4 Voltage Regulator Connections (All Except SR4B for 3500 Engines)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Oil Field Generator Connections (SR4)
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Remove
322C Excavator Hydraulic System Oil Makeup (Swing System)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Main Stator and Voltage Sensing Lead Connections (SR4B for 3500 Engines)
745 and 740 GC & 740 EJECTOR Articulated Truck Systems Tailgate Cylinder
10B Pavemaster Screed Walk-Around Inspection
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0486 - FMI 05
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Eccentric Weight Housing Oil - Change
988G Wheel Loader Electrohydraulic System Machine Preparation for Troubleshooting
24H Motor Grader Cooling System Coolant (ELC) - Change
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Relief Valve (Steering Cylinder Crossover) - Test and Adjust
2000/04/17 Pull the Injector Sleeve with a 139-0692 Sleeve Jaw {0706, 1713}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Tilt Cylinder
777D HAA Off-Highway Truck Retarding
228 and 248 Skid Steer Loaders Machine Systems Hydrostatic System - Test and Adjust
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Ejector Control Valve
988G Wheel Loader Electrohydraulic System Connector Locations
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air/Hydraulic Cylinder (Front Caliper) - Install
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System General Information
Procedure for Salvaging Off-Highway Truck Wheel Bolt Holes or Stud Holes{4201} Procedure for Salvaging Off-Highway Truck Wheel Bolt Holes or Stud Holes{4201}