Axle Oil Cooler - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 将工具 (A) 和适当的起吊设备安装到车桥油冷却器 (18) 上后定位车桥油冷却器 (18) 。 车桥油冷却器 (18) 的重量约为 80 kg (175 lb)。
Show/hide table
图 1 | g00686880 |
Show/hide table
图 2 | g00686883 |
- 定位支架 (21) 并安装螺栓 (22) 。
- 安装螺栓 (20) 。
Show/hide table
图 3 | g00686881 |
- 安装螺栓 (19) 和夹子。
- 安装螺栓 (17) 和螺栓 (16) 。
Show/hide table
图 4 | g00686878 |
Show/hide table
图 5 | g00686822 |
- 连接软管组件 (13) 和 (14) 。
Show/hide table
图 6 | g00686821 |
- 安装螺栓 (15) 和夹子。
- 连接线束组件 (11) 和 (12) 。
Show/hide table
图 7 | g00686819 |
- 将适当的起吊设备固定到平台组件 (10) 上后定位平台组件 (10) 。 平台组件 (10) 的重量约为 64 kg (140 lb)。
Show/hide table
图 8 | g00686817 |
- 安装螺栓 (9) 。
Show/hide table
图 9 | g00686816 |
- 安装螺栓 (8) 。
Show/hide table
图 10 | g00686815 |
- 安装螺栓 (7) 。
Show/hide table
图 11 | g00686814 |
- 连接软管组件 (5) 后安装电缆带。
Show/hide table
图 12 | g00686812 |
- 定位格栅 (4) 后安装螺栓 (3) 。
Show/hide table
图 13 | g00686811 |
- 安置护罩 (1) 和螺栓 (2) 。
Show/hide table
图 14 | g00686810 |
End By: 分离转向机架锁。 请参阅 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
988G Wheel Loader Power Train Axle Oil Cooler - Remove
2000/03/27 Correction to Service Magazine, SEPD0432 , "Improved Transmission Downshift Switch Now Used" {5063, 7332}
CB-534C Vibratory Compactor Towing the Machine
2000/05/08 Stops Have Now Been Added To The Crankcase Guard. {7151}
988G Wheel Loader Power Train Service Brake - Assemble
988G Wheel Loader Power Train Service Brake - Disassemble
CB-535B Vibratory Compactor Propel System Piston Pump (Propel)
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Thickness Control Screw Adjustment
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Main Frame Extension Installation
988G Wheel Loader Power Train Final Drive, Brake and Wheel - Remove
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Monitoring System
CB-534C Vibratory Compactor Roading the Machine
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Hydrostatic Drive System Performance - Test
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Initial Troubleshooting Procedure
988G Wheel Loader Power Train Axle Oil Cooler - Disassemble
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Using Service Mode
2000/03/20 An Improved Ball Stud Is Now Used for the Gas Spring on the Armrest {7307, 7312}
TH103 Telehandler Hydraulic System Joystick Control
988G Wheel Loader Power Train Axle Oil Cooler - Assemble
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks E015 High Engine Coolant Temperature Derate
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks E025 High Inlet Air Temperature Derate
325D and 329D Excavators Fuel Tank Cap and Strainer - Clean
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders MID 036 - CID 0298 - FMI 02 Incorrect Service Brake Pedal Switch inputs
2000/03/20 Changes to Operation and Maintenance Manuals, SEBU7207 and SEBU7255 {3261, 7000}