Axle Oil Cooler - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
开始:
- 连接转向机架锁。 请参阅拆解和组装, "转向机架锁 - 分离和连接"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
注: 在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记,以便安装。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏,并有助于防止污染物进入系统。
- 卸下螺栓 (2) 和防护罩 (1) 。
Show/hide table
图 1 | g00686810 |
- 拆下螺栓 (3) 和格栅 (4) 。
Show/hide table
图 2 | g00686811 |
- 断开软管组件 (5) 。 拆下电缆带后将软管组件 (5) 定位到侧面上。
Show/hide table
图 3 | g00686812 |
- 将适当的起吊设备固定到扶手 (6) 上。
Show/hide table
图 4 | g00686813 |
- 拆下螺栓 (7) 。
Show/hide table
图 5 | g00686814 |
- 拆下螺栓 (8) 。
Show/hide table
图 6 | g00686815 |
- 拆下螺栓 (9) 。
Show/hide table
图 7 | g00686816 |
- 拆下平台组件 (10) 。 平台组件 (10) 的重量约为 64 kg (140 lb)。
Show/hide table
图 8 | g00686817 |
- 断开软管组件 (11) 和 (12) 。
Show/hide table
图 9 | g00686819 |
- 断开软管组件 (13) 和 (14) 。
Show/hide table
图 10 | g00686821 |
- 拆下螺栓 (15) 和夹子。
- 拆下螺栓 (16) 。
Show/hide table
图 11 | g00686822 |
- 拆下螺栓 (17) 。
Show/hide table
图 12 | g00686878 |
- 将工具 (A) 和适当的起吊设备固定到车桥油冷却器 (18) 上。
Show/hide table
图 13 | g00686880 |
- 拆下螺栓 (19) 和夹子。
Show/hide table
图 14 | g00686881 |
- 拆下螺栓 (20) 。
- 拆下螺栓 (22) 和托架 (21) 。
Show/hide table
图 15 | g00686883 |
- 拆下车桥油冷却器 (18) 。 车桥油冷却器 (18) 的重量约为 80 kg (175 lb)。
Show/hide table
图 16 | g00686905 |
Caterpillar Information System:
2000/03/27 Correction to Service Magazine, SEPD0432 , "Improved Transmission Downshift Switch Now Used" {5063, 7332}
CB-534C Vibratory Compactor Towing the Machine
2000/05/08 Stops Have Now Been Added To The Crankcase Guard. {7151}
988G Wheel Loader Power Train Service Brake - Assemble
988G Wheel Loader Power Train Service Brake - Disassemble
CB-535B Vibratory Compactor Propel System Piston Pump (Propel)
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Thickness Control Screw Adjustment
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Main Frame Extension Installation
988G Wheel Loader Power Train Final Drive, Brake and Wheel - Remove
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Monitoring System
CB-534C Vibratory Compactor Roading the Machine
797 Off-Highway Truck Power Train Rear Wheel and Differential Fastener
988G Wheel Loader Power Train Axle Oil Cooler - Install
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Hydrostatic Drive System Performance - Test
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Initial Troubleshooting Procedure
988G Wheel Loader Power Train Axle Oil Cooler - Disassemble
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Using Service Mode
2000/03/20 An Improved Ball Stud Is Now Used for the Gas Spring on the Armrest {7307, 7312}
TH103 Telehandler Hydraulic System Joystick Control
988G Wheel Loader Power Train Axle Oil Cooler - Assemble
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks E015 High Engine Coolant Temperature Derate
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks E025 High Inlet Air Temperature Derate
325D and 329D Excavators Fuel Tank Cap and Strainer - Clean
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders MID 036 - CID 0298 - FMI 02 Incorrect Service Brake Pedal Switch inputs