Transmission Oil Filter Base - Remove and Install
拆卸步骤
开始:
- 卸下变速箱机油滤清器。 请参阅解体和组装, "变速箱机油滤清器 - 拆卸和安装"，了解正确的步骤。
- 从变速箱机油滤清器座 (2) 上断开软管组件上的管接头 (1) 。
Show/hide table
 | |
| 图 1 | g00638958 |
Show/hide table
 | |
| 图 2 | g00638956 |
- 卸下八个螺栓 (5) 、垫圈和四个半法兰 (4) ，断开两个软管组件 (3) 。 堵住软管管接头，以免机油损耗，保证机油系统无污垢。
- 从变速箱机油滤清器座 (2) 上卸下四个螺栓 (6) 。从安装支架上卸下变速箱机油滤清器座 (2) 。
- 从变速箱机油滤清器座 (2) 上卸下塞 (10) 。
Show/hide table
 | |
| 图 3 | g00621160 |
注: 当前机型的变速箱机油滤清器座 (2) 顶部只有一个管接头。
- 从塞 (10) 上卸下 O 形密封圈 (9) 。
- 从变速箱机油滤清器座 (2) 上卸下滑阀 (8) 和弹簧 (7) 。
安装步骤
注: 安装之前先核实差速器及伞齿轮的所有部件清洁无异物。
注: 检查所有部件和所有 O 形密封圈是否磨损或损坏。 必要时，更换部件。 在密封的地方，用润滑油将 O 形密封圈稍加润滑。
- 将 O 形密封圈 (9) 安装在塞 (10) 上。
Show/hide table
| | |
| 图 4 | g00621160 |
注: 当前机型的变速箱机油滤清器座 (2) 顶部只有一个管接头。
- 将弹簧 (7) 、滑阀 (8) 和塞 (10) 安装在变速箱机油滤清器座 (2) 。
- 将变速箱机油滤清器座 (2) 安置在安装支架上。 安装四个螺栓 (6) 和垫圈，将变速箱机油滤清器座 (2) 固定在安装支架上。
Show/hide table
| | |
| 图 5 | g00638958 |
Show/hide table
| | |
| 图 6 | g00638956 |
- 将两个软管 (3) 安置在变速箱机油滤清器座 (2) 上。 安装四个半法兰 (4) 、八个螺栓 (5) 和垫圈。
- 将软管组件的管接头 (1) 连接在变速箱机油滤清器座 (2) 上。
End By: 安装变速箱机油滤清器。 请参阅 解体和组装, "变速箱机油滤清器 - 拆卸和安装"，了解正确的步骤。
Caterpillar Information System:
Retrofitting Telescopic Material Handlers (RT Series) for the use of pilot control valves that are currently used in TH62 through TH103 machines{5059, 6400} Retrofitting Telescopic Material Handlers (RT Series) for the use of pilot control valves that are currently used in TH62 through TH103 machines{5059, 6400}
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Engine Speed/Timing Sensor - Calibrate
572R Pipelayer Engine Supplement Hydraulic Oil Cooler - Remove and Install
D350E Series II and D400E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Accumulator (Suspension)
D350E Series II and D400E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Control Valve
980G Wheel Loader Power Train Oil Filter (Power Train)
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Lower Roller - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Mode 12 - Machine Features Configuration
572R Pipelayer Engine Supplement Engine Oil Filter and Base - Install
572R Pipelayer Engine Supplement Engine Oil Filter and Base - Remove
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Feed Roller Arm - Install
980G Wheel Loader Power Train Transmission Oil Pump
C-10 and C-12 Industrial Engines Electrical Ground Stud
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electronic Display Module
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Engine Oil Level Switch
CB-214D, CB-224D and CB-225D Vibratory Compactors Stopping the Machine
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Upper Roller - Remove and Install
572R Pipelayer Engine Supplement Fan Guard - Remove and Install
980G Wheel Loader Power Train Output Transfer Gears
CB-214D, CB-224D and CB-225D Vibratory Compactors Lifting and Tying Down the Machine
HH45, HH55, HH65 and HH75 Harvester Heads Tree Harvester Head Preparation for Disassembly
539 Knuckleboom Loader Hydraulic System Swing Motor Case Drain Oil - Measure
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Throttle Position Sensor
980G Wheel Loader Power Train Differential