Front Axle - Install
安装步骤
- 冷却轴承 (13) 。使用工具 (C) ,将轴承 (13) 安装在车轴后部中。
注: 安装之前先核实前轴的所有部件清洁无异物。
注: 检查所有部件和所有 O 形密封圈是否磨损或损坏。 必要时,更换部件。 在密封的地方,用润滑油将 O 形密封圈稍加润滑。
Show/hide table
图 1 | g00634805 |
- 安装轴承 (13) ,直到轴承 (13) 处于车轴正面以下 7.2 ± 0.4 mm (0.28 ± 0.02 in) 的位置。
- 使用工具 (C) ,安装唇形密封 (12) 。安装唇形密封 (12) ,密封唇朝外。
- 使唇形密封 (12) 靠在轴承 (13) 上落座。
- 冷却轴承 (9) 。 使用工具 (C) ,将轴承 (9) 安装在车轴前部中。安装轴承 (9) ,直到轴承 (9) 处于车轴正面以下 7.2 ± 0.4 mm (0.28 ± 0.02 in) 的位置。
Show/hide table
图 2 | g00634809 |
- 使用工具 (C) ,安装唇形密封 (10) 。安装唇形密封 (10) ,密封唇朝外。
- 使唇形密封 (10) 靠在轴承 (9) 上落座。将薄薄一层 5P-0960 含钼润滑油 涂覆在轴承 (9) 和唇形密封 (10) 上。
- 将车轴安置在机器底下。 将起吊设备连接在车轴上。车轴的重量为 976 kg (2152 lb)。将车轴缓慢升高至机架的原有位置。将销定位孔相互对正。
- 将垫圈 (11) 安装在车轴后部与机架之间。
Show/hide table
图 3 | g00634784 |
- 将厚垫圈安装在车轴前部与机架之间。
- 将薄薄一层 5P-0960 含钼润滑油 涂覆在销 (8) 上。安装销 (8) 。
Show/hide table
图 4 | g00634783 |
- 向后滑动车轴。检查车轴前部与机架的间隙。必要时使用 2G-5673 垫圈 ,使车轴前部与机架的最大间隙保持在 1.5 mm (0.06 in)。
- 对正将销 (8) 固定在机架上的定位螺栓 (7) 、螺母及垫圈的定位孔。安装定位螺栓 (7) 、螺母和垫圈,将销 (8) 固定在机架上。
注: 旧机型有一个轴销,销端有一个定位板。 一个螺栓将此定位板固定在机架上。
Show/hide table
图 5 | g00634777 |
- 连接软管组件 (1) 、 (2) 、 (3) 、 (4) 、 (5) 和 (6) 。
Show/hide table
图 6 | g00634775 |
Show/hide table
图 7 | g00634776 |
- 安装前轮胎和轮缘。 请参阅解体和组装, "前轮胎和轮缘 - 拆卸和安装",了解正确的步骤。
- 使用工具 (A) (图上未显示),将车轮降至地面。 从机器旁撤走工具 (A) 。
End By:
- 加注液压油箱至正确油位。 请参阅 操作和保养手册, "液压油 - 加注",了解正确的步骤。
- 起动机器,移动机具、转向并倾斜车轮,除去液压系统的空气。
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
561M Pipelayer Control Valve (Boom Stop) - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Connectors and Functions
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
416C, 426C, 428C, 436C and 438C Backhoe Loaders Air Inlet Heater Starting Aid
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Cat Data Link
12H, 140H and 160H Motor Graders Machine Systems Front Axle - Remove
12H, 140H and 160H Motor Graders Machine Systems Wheel Lean Cylinder - Remove and Install
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Service Brake Control Valve - Check
C9 Engine For Caterpillar Built Machines Cylinder Head - Remove
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Pressure Reducing Valve (Hoist Pilot Pressure) - Test and Adjust
561M Pipelayer Control Valve (Boom Stop) - Assemble
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder - Test
777D HAA Off-Highway Truck Engine Air Filter Service Indicator - Inspect
12H, 140H and 160H Motor Graders Machine Systems Accumulator (Blade Cushion) - Remove and Install
3056 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 05 Engine Cooling Fan Solenoid open circuit
12H, 140H and 160H Motor Graders Machine Systems Blade Lift - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 06 Engine Cooling Fan Solenoid short to ground
3524B Engines for Off-Highway Trucks MID 036 - CID 0296 - FMI 09 Unable to communicate with Transmission ECM
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Directional Shift Management Function
527 Track-Type Skidder Machine Supplements Bulldozer Lift Cylinder - Assemble