Accumulator (Blade Cushion) - Remove and Install
拆卸步骤
- 释放液压系统压力。 请参阅解体和组装, "解体和组装时的机器准备事项"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
高温机油或高温部件可能会导致人身伤害。 在工作温度下,机油温度高,压力高。 热油能造成烫伤。 只能在发动机停机且加注口盖充分冷却到可以徒手触及时再卸下加注口盖。 不让高温油或部件与皮肤接触。 |
Show/hide table
突然释放高压机油可能会导致人身伤害。 一定要关闭发动机至少五分钟,保证蓄能器压力为零。 蓄能器充满干氮气。不要松开蓄能器顶部的阀或卸下盖。 |
- 从平地刮铲缓冲蓄能器上卸下导线线束 (3) 。 从平地刮铲缓冲蓄能器上卸下导线线束 (5) 。
Show/hide table
图 1 | g00634818 |
注: 为便于安装,在所有软管组件、所有导线线束及所有管上做出识别标记。 塞好并盖住所有软管组件和管,以防液体损失、系统污染。
- 从平地刮铲缓冲蓄能器上断开软管组件 (4) 和软管组件 (6) 。
- 卸下将蓄能器阀固定在机架上的两个螺栓和垫圈 (2) 。
- 卸下将平地刮铲缓冲蓄能器固定在机架上的两个螺栓 (1) 、两个垫圈和两个卡箍。卸下两个平地刮铲缓冲蓄能器。
安装步骤
- 将两个平地刮铲缓冲蓄能器在机架上放置到位。安装固定平地刮铲缓冲蓄能器的两个螺栓 (1) 、两个垫圈和两个卡箍。
Show/hide table
图 2 | g00634818 |
注: 清洁度是一项重要的因素。 组装步骤开始之前,应彻底清洁部件外部。 这有助于防止系统污染。
- 安装将蓄能器阀固定在机架上的两个垫圈和两个螺栓 (2) 。
- 将软管组件 (4) 和软管组件 (6) 安装在平地刮铲缓冲蓄能器的原有位置。
- 将导线线束 (3) 和导线线束 (5) 连接在原有位置。
- 检查平地刮铲缓冲蓄能器的充压压力。 必要时,向平地刮铲缓冲蓄能器充压。 请参阅技术规范, "蓄能器(平地刮铲缓冲)",了解正确的充压压力。
Show/hide table
干燥氮气是唯一被认可用作蓄能器充气的气体。 用氧气对蓄能器充气会引起爆炸。 如果用的氮气罐配上符合 CGA ( 压缩气体协会(Compressed Gas Association)标准公司) 的 580号 接头,就不会产生危险。 购买氮气时,确保氮气罐上配有 CGA No. 580 接头 不要用颜色标记,或其它方法来 认定氮气和氧气罐之间的区别。 |
Caterpillar Information System:
777D HAA Off-Highway Truck Engine Air Filter Service Indicator - Inspect
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder - Test
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
12H, 140H and 160H Motor Graders Machine Systems Front Axle - Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
561M Pipelayer Control Valve (Boom Stop) - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Connectors and Functions
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
416C, 426C, 428C, 436C and 438C Backhoe Loaders Air Inlet Heater Starting Aid
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Cat Data Link
12H, 140H and 160H Motor Graders Machine Systems Front Axle - Remove
12H, 140H and 160H Motor Graders Machine Systems Wheel Lean Cylinder - Remove and Install
3056 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 05 Engine Cooling Fan Solenoid open circuit
12H, 140H and 160H Motor Graders Machine Systems Blade Lift - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 06 Engine Cooling Fan Solenoid short to ground
3524B Engines for Off-Highway Trucks MID 036 - CID 0296 - FMI 09 Unable to communicate with Transmission ECM
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Directional Shift Management Function
527 Track-Type Skidder Machine Supplements Bulldozer Lift Cylinder - Assemble
CS-531D, CP-533D and CS-533D Vibratory Compactors Tire Inflation - Check
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Electronic Control Module (ECM) - Replace
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0526 - FMI 05 Turbo Wastegate Drive current low
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Neutral Start Function