Vibration Damper and Pulley - Remove
Removal Procedure
Start By:
- Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1) in order to remove vibration damper (2) .
Note: Do not use a puller tool to remove the crankshaft pulley from the crankshaft.
Show/hide table
Illustration 1 | g00891801 |
- Remove bolts (3) .
Show/hide table
Illustration 2 | g00891807 |
- Hold a wood block against the inner hub of the crankshaft pulley as shown. Strike the wood block with a hammer in order to loosen the split lock and the spacer.
Show/hide table
Illustration 3 | g00902007 |
- Carefully remove crankshaft pulley (8) . The weight of the crankshaft pulley is approximately 10 kg (22 lb).
- Remove thrust block (5) and O-ring seal (4) .
Show/hide table
Illustration 4 | g01513048 |
- Remove spacer (6) and split locks (7) from crankshaft pulley (8) .
Caterpillar Information System:
12H, 140H and 160H Motor Graders Machine Systems Accumulator (Blade Cushion) - Remove and Install
777D HAA Off-Highway Truck Engine Air Filter Service Indicator - Inspect
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder - Test
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
12H, 140H and 160H Motor Graders Machine Systems Front Axle - Install
C9 Engine For Caterpillar Built Machines Cylinder Head - Install
561M Pipelayer Control Valve (Boom Stop) - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Connectors and Functions
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Electrical Connector - Inspect
416C, 426C, 428C, 436C and 438C Backhoe Loaders Air Inlet Heater Starting Aid
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Cat Data Link
12H, 140H and 160H Motor Graders Machine Systems Front Axle - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 05 Engine Cooling Fan Solenoid open circuit
12H, 140H and 160H Motor Graders Machine Systems Blade Lift - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 06 Engine Cooling Fan Solenoid short to ground
3524B Engines for Off-Highway Trucks MID 036 - CID 0296 - FMI 09 Unable to communicate with Transmission ECM
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Directional Shift Management Function
527 Track-Type Skidder Machine Supplements Bulldozer Lift Cylinder - Assemble
CS-531D, CP-533D and CS-533D Vibratory Compactors Tire Inflation - Check
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Electronic Control Module (ECM) - Replace
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0526 - FMI 05 Turbo Wastegate Drive current low
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Neutral Start Function
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust